fuel MERCEDES-BENZ SPRINTER 2006 User Guide

TEST ACTION APPLICABILITY
4 Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Disconnect the Instrument Cluster C1 harness connector.
Measure the resistance of the Fuel Level Sensor Signal (+) circuit between the Fuel
Pump Module harness connector and the Instrument Cluster harness connector.
Is the resistance above 10 ohms?All
Ye s!Repair the Fuel Level Sensor Signal (+) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
No!Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
183
INSTRUMENT CLUSTER
FUEL LEVEL SENSOR OPEN/SHORT TO BATTERY ÐContinued

Symptom:
FUEL LEVEL SENSOR SHORT TO GROUND
POSSIBLE CAUSES
FUEL LEVEL SENSOR
FUEL LEVEL SENSOR CIRCUITS SHORTED TOGETHER
INSTRUMENT CLUSTER
FUEL LEVEL SENSOR SIGNAL (+) SHORT TO GROUND
TEST ACTION APPLICABILITY
1 Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Turn the ignition on, with the DRBIIIt, read DTCs.
Does the DRBIIItdisplay: Fuel Level Sensor Shorted to Ground?All
Ye s!Go To 2
No!Replace the Fuel Level Sensor in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
2 Turn the ignition off.
Disconnect the Instrument Cluster C1 harness connector.
Disconnect the Fuel Pump Module harness connector.
Measure the resistance between ground and the Fuel Level Sensor Signal (+) circuit.
Is the resistance below 1000 ohms?All
Ye s!Repair the Fuel Level Sensor Signal (+) circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No!Go To 3
3 Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Disconnect the Instrument Cluster C1 harness connector.
Measure the resistance between the Fuel Level Sensor Signal (+) circuit and Fuel
Level Sensor Signal Return circuit.
Is the resistance below 1000 ohms?All
Ye s!Repair the Fuel Level Sensor Signal (+) circuit for a short to the
Sensor Return circuit.
Perform BODY VERIFICATION TEST - VER 1.
No!Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
184
INSTRUMENT CLUSTER

HEATER VERIFICATION TEST - VER 1 APPLICABILITY
1. WARNING: NEVER OPERATE THE HEATER IN AN ENCLOSED AREA THAT DOES
NOT HAVE EXHAUST VENTILATION FACILITIES. ALWAYS VENT THE HEATER's
EXHAUST WHEN OPERATING THE HEATER. FAILURE TO FOLLOW THESE IN-
STRUCTIONS CAN RESULT IN PERSONAL INJURY OR DEATH.
2. WARNING: ALLOW THE HEATER ASSEMBLY TO COOL BEFORE PERFORMING A
COMPONENT INSPECTION/REPAIR/REPLACEMENT. FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY OR DEATH.
3. NOTE: The heater's control unit will store up to five DTCs in its memory.
4. NOTE: If the heater's control unit detects a new fault in the system, one that is not
already stored in its memory, it will clear the oldest of the five stored DTCs, and it
will store the new fault's DTC.
5. NOTE: If the heater's control unit detects a reoccurrence of a stored fault, it will
overwrite that fault's DTC with the most recent occurrence.
6. Verify that the vehicle's battery is fully charged.
7. Verify that there is more than 1/8 of a tank of fuel in the vehicle's fuel tank. Add fuel, if
necessary.
8. Verify that all heater's coolant hoses and fuel lines are securely fastened to their respective
components.
9. Disconnect all jumper wires and reconnect all previously disconnected components and
connectors.
10. If a heater installation/cooling system service was performed, purge the coolant circuit of air
in accordance with the Service Information.
11. Turn the ignition on.
12. Verify that the Cabin Heater or Heater Booster is switched off.
13. Ensure that all accessories are turned off.
14. Set the blend control to the max heat position and the mode control to the floor position.
15. If a fuel system service requiring fuel to drain out of the heater's fuel line was performed,
prime the heater's Dosing Pump in accordance with the Service Information.
16. With the DRBIIIt, record and erase all DTCs from the Cabin Heater Module or Heater
Booster Module. Turn the ignition off, wait 5 seconds, then turn start the engine.
17. Allow the engine to idle.
18. NOTE: Do not disconnect the vehicle's battery or the heater's main power supply
while the heater is in operation or in run-down mode. Failure to follow these
instructions can result in excess emissions from the heater during heater operation.
19. Switch the Cabin Heater or Heater Booster on. Allow the heater to run through at least one
cycle of operation (approximately 10 minutes), and then turn the heater off.
20. With the DRBIIIt, read the Cabin Heater or Heater Booster Module's DTC.
21. Turn the engine off.
Are any DTC's present or is the original condition still present?All
Ye s!Repair is not complete, refer to the appropriate symptom.
No!Repair is complete.
246
VERIFICATION TESTS
Verification Tests ÐContinued

ENGINE CONTROL MODULE C2 (OBD)CAV CIRCUIT FUNCTION
1 16BK/RD FUSED ENGINE CONTROL RELAY OUTPUT
2 14BR GROUND
3 14BK/BL FUSED ENGINE CONTROL RELAY OUTPUT
4 14BR GROUND
5 14BK/BL FUSED ENGINE CONTROL RELAY OUTPUT
6 14BR GROUND
7 18RD S/C SWITCH 12 VOLT SUPPLY
8 18BR/WT HIGH IDLE ON SIGNAL
10 18WT/RD BOOST PRESSURE SENSOR 5 VOLT SUPPLY
11 18WT/DG BOOST PRESSURE SENSOR SIGNAL
12 18BR/WT SENSOR GROUND
13 18GY/DG ACCEL PEDAL POSITION SENSOR SIGNAL NO. 2
14 18BR/GY ACCEL PEDAL POSITION SENSOR GROUND NO. 2
17 18BR/DG KICKDOWN SWITCH SIGNAL
18 20DG/YL ENGINE RPM
19 18BK FUSED IGNITION SWITCH OUTPUT (RUN-START)
24 18BL/RD ACCEL PEDAL POSITION SENSOR 5 VOLT SUPPLY
25 18BL/DG ACCEL PEDAL POSITION SENSOR SIGNAL NO. 1
26 18BR/BL ACCEL PEDAL POSITION SENSOR GROUND NO. 1
28 18BR/DG INTAKE AIR TEMPERATURE SENSOR GROUND
31 20BL/YL K-ECM
32 20DG ENHANCED ACCIDENT REPORT DRIVER
36 18VT IGNITION SWITCH OUTPUT (START)
37 18DG ACCEL/SET SIGNAL
38 18BK VERIFICATION SIGNAL
42 18DG/WT INTAKE AIR TEMPERATURE SENSOR SIGNAL
43 18BK/RD GLOW PLUG MODULE CONTROL
44 18YL/BL ENGINE CONTROL RELAY CONTROL
50 18YL DECEL/SET SIGNAL
51 18GY OFF SIGNAL
52 18BL RESUME SIGNAL
53 20DG/WT CAN C BUS (+)
54 20DG CAN C BUS (-)
55 18BR/RD FUEL PUMP RELAY CONTROL
58 18VT/DG STARTER MOTOR RELAY CONTROL
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
267
CONNECTOR PINOUTS

EVAPORATOR TEMPERATURE SENSORCAV CIRCUIT FUNCTION
1 18BR/DG EVAPORATOR TEMPERATURE SENSOR SIGNAL
2 18BR/BL SENSOR GROUND
FUEL LEVEL SENSORCAV CIRCUIT FUNCTION
2 20BL/BK FUEL LEVEL SENSOR SIGNAL (+)
3 20BR FUEL LEVEL SENSOR SIGNAL RETURN
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
269
CONNECTOR PINOUTS

INSTRUMENT CLUSTER C1CAV CIRCUIT FUNCTION
1 20BR FUEL LEVEL SENSOR SIGNAL RETURN
2 20BR/DG AMBIENT TEMPERATURE SENSOR SIGNAL RETURN
4 20WT/GY K-IC/ATC/HBM/CHM
5 20BR/BK PARK BRAKE INDICATOR SIGNAL
7 20BK/DG RIGHT TURN SIGNAL
10 20BL/BK FUEL LEVEL SENSOR SIGNAL (+)
11 20BL/DG AMBIENT TEMPERATURE SENSOR SIGNAL (+)
14 20DG/WT/BL ENGINE COOLANT LEVEL SWITCH SIGNAL
15 20BR/WT FRONT COURTESY LAMPS CONTROL
16 20YL/RD SEAT BELT SWITCH SIGNAL
17 20DG CAN C BUS (-)
18 20DG/WT CAN C BUS (+)
INSTRUMENT CLUSTER C2 - WHITECAV CIRCUIT FUNCTION
1- -
2- -
3 20RD/YL FUSED B(+)
4 20BR/WT BRAKE WEAR SENSOR SIGNAL
5- -
6 18BR GROUND
7 20GY/DG/RD LAMP DRIVER
8 20BL/WT FUSED HIGH BEAM SWITCH OUTPUT
9 20BL/RD/WT VEHICLE SPEED SENSOR OUTPUT
10 20BK FUSED IGNITION SWITCH OUTPUT (RUN-START)
11 20BL/BK KEY-IN IGNITION SWITCH SIGNAL
12 - -
13 20BK/WT LEFT TURN SIGNAL
14 20BR/YL BRAKE FLUID LEVEL INDICATOR SIGNAL
15 20BL GENERATOR FIELD DRIVER
16 20YL AIRBAG WARNING INDICATOR DRIVER
17 - -
18 20BL/VT D(+) RELAY NO. 1 CONTROL
18 20BL/VT D(+) RELAY NO. 1 CONTROL
INTRUSION SENSOR NO. 1 - BLACKCAV CIRCUIT FUNCTION
1 20BR GROUND
2 20DG/BK INTRUSION SENSOR 1 SIGNAL
3 20DG/YL INTRUSION SENSOR INTERFACE
4 20RD/DG FUSED B(+)
INTRUSION SENSOR NO. 2 - BLACKCAV CIRCUIT FUNCTION
1 20BR GROUND
2 20GY/BK INTRUSION SENSOR 2 SIGNAL
3 20DG/YL INTRUSION SENSOR INTERFACE
4 20RD/DG FUSED B(+)
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
279
CONNECTOR PINOUTS

TABLE OF CONTENTS - Continued
P1617- ECM WRITE ERROR..............................................16
P1617-ECM INCORRECT VALUE..........................................16
P1617-ECM READ ERROR...............................................16
P2122-INTERNAL ERROR COUNTER FAULT................................16
P2122-INTERNAL ERROR ENGINE SHUT OFF..............................16
P2122-INTERNAL ERROR ENGINE VOLTAGE MONITORING...................16
P2122-INTERNAL ERROR ENGINE VOLTAGE MONITORING...................16
P2123-INJECTOR BANK ERROR..........................................16
P2124-INJECTOR BANK ERROR..........................................16
P2139-ECM INJECTOR OUTPUT STAGE #1.................................16
P2139-ECM INJECTOR OUTPUT STAGE #1 SHORT CIRCUIT..................16
P2140-ECM INJECTOR OUTPUT STAGE #2.................................16
P2140-ECM INJECTOR OUTPUT STAGE #2 SHORT CIRCUIT..................16
P2149-ECM A/D CONVERTER HIGH.......................................16
P2149-ECM A/D CONVERTER LOW........................................16
P2149-ECM A/D CONVERTER PLAUSIBILITY................................16
P2153-STARTER RELAY CIRCUIT ECM THERMAL OVERLOAD................16
P2197-FUEL QUANTITY SOLENOID ECM THERMAL OVERLOAD...............16
P2214-CAN MESSAGE ERROR...........................................16
P2319-ECM INTERNAL ERROR 1..........................................16
P2319-ECM INTERNAL ERROR 2..........................................16
P2319-ECM INTERNAL ERROR 3..........................................16
P2319-ECM INTERNAL ERROR 4..........................................16
P2321-ECM INTERNAL ERROR 5..........................................16
P2323-ECM INTERNAL ERROR...........................................16
P2324-ECM INJECTOR MONITORING 1....................................16
P2324-ECM INJECTOR MONITORING 2....................................16
P2324-ECM INJECTOR MONITORING 3....................................16
P2324-ECM INJECTOR MONITORING 4....................................16
P2324-ECM INJECTOR UNDERVOLTAGE...................................16
P2325-ECM INTERNAL ERROR 1..........................................16
P2325-ECM INTERNAL ERROR 2..........................................16
P2325-ECM INTERNAL ERROR 3..........................................16
P2325-ECM INTERNAL ERROR 4..........................................16
P2329-ECM INTERNAL ERROR 1..........................................16
P2330-ECM INTERNAL ERROR 1..........................................16
P2340-ECM INJECTION QUANTITY ERROR.................................16
P2342-ECM INTERNAL ERROR 1..........................................16
P2342-ECM INTERNAL ERROR 2..........................................17
P2350-INTERNAL VOLTAGE ERROR.......................................17
P2352-INJECTION FAULT - EXCESSIVE TEMPERATURE......................17
P2352-INJECTION FAULT - QUANTITY ERROR..............................17
P2352-INJECTION FAULT - TORQUE LIMIT.................................17
P2352-INJECTION FAULT EXCESSIVE ENGINE SPEED.......................17
P2354-ECM INTERNAL FAULT............................................17
P2356-ECM INTERNAL ERROR...........................................17
P2357-ECM INTERNAL ERROR...........................................17
P2358-ECM INTERNAL ERROR...........................................17
P2500-FUEL PRESSURE SOLENOID CIRCUIT EXCESSIVE CURRENT..........17
P2514-CRANKCASE VENT HEATER EXCESSIVE CURRENT...................17
P2526-BOOST PRESSURE SERVO MOTOR EXCESSIVE CURRENT............17
P2527-EGR VALVE EXCESSIVE CURRENT.................................17
P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW...............19
ii

TABLE OF CONTENTS - Continued
P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW...............19
P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH.........19
P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW..........19
P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH...............19
P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW...............19
P2065-MASS AIR FLOW SENSOR SUPPLY VOLTAGE TOO HIGH...............19
P2065-MASS AIR FLOW SENSOR SUPPLY VOLTAGE TOO LOW...............19
P2067-MASS AIR FLOW SENSOR SIGNAL CIRCUIT OPEN OR SHORTED.......19
P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH...............19
P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW...............19
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO ERROR........19
P2633-MAF SENSOR SIGNAL PLAUSIBILITY................................19
P0105-INTAKE PRESSURE SENSOR CAN MESSAGE ERROR.................25
P0105-INTAKE PRESSURE SENSOR PLAUSIBILITY..........................25
P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH.............28
P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW.............31
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH..............34
P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH......34
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW...............37
P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW......37
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY.............40
P2012-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY.............40
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY WITH ENGINE
OIL SENSOR...........................................................42
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO
HIGH.................................................................44
P2054-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO
HIGH.................................................................44
P2054-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO
LOW..................................................................44
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO
LOW..................................................................47
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO HIGH. .49
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO LOW . .51
P2625-FUEL TEMPERATURE SENSOR PLAUSIBILITY........................51
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO HIGH.....53
P2008-FUEL PRESSURE SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH......53
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO LOW.....57
P2008-FUEL PRESSURE SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW.......57
P0201-CYLINDER 1-INJECTOR CIRCUIT EXCESSIVE CURRENT...............60
P0201-CYLINDER 1-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND.....60
P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO GROUND..............60
P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO VOLTAGE..............60
P0202-CYLINDER 2-INJECTOR CIRCUIT EXCESSIVE CURRENT...............60
P0202-CYLINDER 2-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND.....60
P0202-CYLINDER 2-INJECTOR CIRCUIT SHORTED TO GROUND..............60
P0202-CYLINDER 2-INJECTOR CIRCUIT SHORTED TO VOLTAGE..............60
P0203-CYLINDER 3-INJECTOR CIRCUIT EXCESSIVE CURRENT...............60
P0203-CYLINDER 3-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND.....60
P0203-CYLINDER 3-INJECTOR CIRCUIT SHORTED TO GROUND..............60
P0203-CYLINDER 3-INJECTOR CIRCUIT SHORTED TO VOLTAGE..............60
P0204-CYLINDER 4-INJECTOR CIRCUIT EXCESSIVE CURRENT...............60
P0204-CYLINDER 4-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND.....60
iii

TABLE OF CONTENTS - Continued
P1480-GLOW PLUG INDICATOR ERROR...................................79
P1482-GLOW PLUG MODULE - COMMUNICATION ERROR....................80
P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW FAULT...................80
P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW SHORT TO GROUND.......80
P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW SHORT TO VOLTAGE......80
P1482-GLOW PLUG MODULE - EXCESS CURRENT..........................82
P2133-GLOW PLUG #1 CIRCUIT EXCESSIVE CURRENT......................82
P2133-GLOW PLUG #1 CIRCUIT OPEN CIRCUIT............................82
P2133-GLOW PLUG #1 CIRCUIT SHORT TO GROUND.......................82
P2133-GLOW PLUG #1 CIRCUIT SHORT TO VOLTAGE.......................82
P2134-GLOW PLUG #2 CIRCUIT EXCESSIVE CURRENT......................82
P2134-GLOW PLUG #2 CIRCUIT OPEN CIRCUIT............................82
P2134-GLOW PLUG #2 CIRCUIT SHORT TO GROUND.......................82
P2134-GLOW PLUG #2 CIRCUIT SHORT TO VOLTAGE.......................82
P2135-GLOW PLUG #3 CIRCUIT EXCESSIVE CURRENT......................82
P2135-GLOW PLUG #3 CIRCUIT OPEN CIRCUIT............................82
P2135-GLOW PLUG #3 CIRCUIT SHORT TO GROUND.......................82
P2135-GLOW PLUG #3 CIRCUIT SHORT TO VOLTAGE.......................82
P2136-GLOW PLUG #4 CIRCUIT EXCESSIVE CURRENT......................82
P2136-GLOW PLUG #4 CIRCUIT OPEN CIRCUIT............................82
P2136-GLOW PLUG #4 CIRCUIT SHORT TO GROUND.......................82
P2136-GLOW PLUG #4 CIRCUIT SHORT TO VOLTAGE.......................82
P2137-GLOW PLUG #5 CIRCUIT EXCESSIVE CURRENT......................82
P2137-GLOW PLUG #5 CIRCUIT OPEN CIRCUIT............................82
P2137-GLOW PLUG #5 CIRCUIT SHORT TO GROUND.......................82
P2137-GLOW PLUG #5 CIRCUIT SHORT TO VOLTAGE.......................82
P1482-GLOW PLUG MODULE - INCORRECT TIMER.........................85
P1482-GLOW PLUG MODULE - INTERNAL FAULT...........................85
P2538-GLOW PLUG MODULE COMMUNICATION ERROR.....................85
P2538-GLOW PLUG MODULE EXCESSIVE CURRENT ERROR.................85
P2538-GLOW PLUG MODULE TIMER ERROR...............................85
P1610-ENGINE CONTROL RELAY PLAUSIBILITY............................87
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO EARLY...................89
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE....................91
P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO HIGH..........................94
P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO LOW..........................96
P1612-IGNITION VOLTAGE - VOLTAGE ERROR.............................99
P1615-ECM VOLTAGE SUPPLY IS TOO HIGH..............................100
P1615-ECM VOLTAGE SUPPLY IS TOO LOW...............................100
P1630-IMMOBILIZER...................................................102
P1630-IMMOBILIZER...................................................102
P1630-IMMOBILIZER...................................................102
P1630-IMMOBILIZER...................................................102
P2201-IMMOBILIZER CAN MESSAGE ERROR..............................102
P2243-NO MESSAGE RECEIVED FROM SKREEM..........................102
P1681-ACM CIRCUIT FAULT.............................................104
P1681-ACM CIRCUIT SHORT TO VOLTAGE................................104
P2009-WATER IN FUEL SENSOR - WATER IN FUEL.........................106
P2009-WATER IN FUEL SENSOR SIGNAL ERROR..........................106
P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION....................110
P2010-MASS AIR FLOW SENSOR POSITIVE DEVIATION.....................110
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO LARGE . . .110
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO SMALL . . .110
v

TABLE OF CONTENTS - Continued
P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO HIGH...........112
P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO LOW............112
P2014-ENGINE OIL SENSOR OIL TEMPERATURE PLAUSIBILITY..............113
P2014-ENGINE OIL SENSOR SIGNAL PLAUSIBILITY........................113
P2014-ENGINE OIL SENSOR SIGNAL VOLTAGE IS TOO HIGH................113
P2014-ENGINE OIL SENSOR SIGNAL VOLTAGE IS TOO LOW................113
P2040-ENGINE OIL SENSOR CIRCUIT INVALID LEVEL......................113
P2040-ENGINE OIL SENSOR CIRCUIT LEVEL OUT OF RANGE...............113
P2040-ENGINE OIL SENSOR CIRCUIT LEVEL OUT OF RANGE...............113
P2041-ENGINE OIL SENSOR POOR OIL QUALITY..........................113
P2041-ENGINE OIL SENSOR QUALITY MEASUREMENT ERROR..............113
P2041-ENGINE OIL SENSOR QUALITY PLAUSIBILITY.......................113
P2042-ENGINE OIL SENSOR WATER CONTAMINATION......................113
P2061-ENGINE OIL SENSOR OPEN CIRCUIT..............................113
P2062-ENGINE OIL SENSOR SIGNAL ERROR..............................113
P2062-ENGINE OIL SENSOR SYNCHRONIZATION ERROR...................113
P2015-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL FLOW
EXCEEDED...........................................................117
P2016-FUEL RAIL PRESSURE MALFUNCTION DECELERATION ERROR.......117
P2016-FUEL RAIL PRESSURE MALFUNCTION FUEL FLOW BELOW MINIMUM
QUANTITY............................................................117
P2017-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO LOW . .117
P2018-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO HIGH . .117
P2019-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL PRESSURE
EXCEEDED...........................................................117
P2019-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO LOW . .117
P2020-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO LOW . .117
P2020-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO HIGH....117
P2021-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO LOW.....117
P2023-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO HIGH....117
P2047-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL PRESSURE
EXCEEDED...........................................................117
P2049-FUEL RAIL PRESSURE MALFUNCTION DECELERATION ERROR.......117
P2051-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL PRESSURE
EXCEEDED...........................................................117
P2052-FUEL RAIL PRESSURE MALFUNCTION PLAUSIBILITY WITH FUEL
PRESSURE SOLENOID.................................................117
P2025-INTAKE PRESSURE SENSOR PLAUSIBILITY.........................125
P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH............128
P2030-INTAKE PRESSURE SENSOR CIRCUIT FAULT.......................128
P2030-INTAKE PRESSURE SENSOR OPEN CIRCUIT........................128
P2030-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH............128
P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW............131
P2030-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW............131
P2026-O2 SENSOR CIRCUIT FAULT......................................134
P2026-O2 SENSOR CIRCUIT OPEN CIRCUIT..............................134
P2026-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH..................134
P2026-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW...................134
P2028-O2 SENSOR CIRCUIT FAULT......................................134
P2028-O2 SENSOR CIRCUIT OPEN CIRCUIT..............................134
P2028-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH..................134
P2028-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW...................134
P2032-O2 SENSOR PLAUSIBILITY.......................................134
vi