ignition MERCEDES-BENZ SPRINTER 2012 MY12 Operator’s Manual

Removing the battery cover in the driver's
footwell
X
Remove screws 0047 and slide cover 0046 in
the direction of the arrow.
The screws must protrude beyond the
recesses.
X Remove cover 0046 upwards. Starter battery in the driver's footwell
X
First loosen and remove the negative
terminal clamp so that it is no longer in
contact with the terminal.
X Remove the cover from the positive
terminal.
X Loosen the positive terminal clamp and fold
it up to the side together with the pre-fuse
box. Disconnecting the additional battery
Additional battery in the engine compartment
X
Remove the key from the ignition lock.
X Open the hood (Y page 168).
X First loosen and remove the negative
terminal clamp so that it is no longer in
contact with the terminal.
X Remove the cover from the positive
terminal.
X Loosen and remove the positive terminal
clamp.
Removing the battery Starter battery
X
Disconnect the battery ( Y page 176).
X Pull breather hose with connector
bracket 0047 from connection 0046 on the
degassing cover. Maintenance
177Operation Z

Problem Possible causes/consequences and
0050 Solutions008A
The red SRS
indicator lamp
does not go out
approximately
four seconds
after switching
on the ignition,
or lights up
again. G
Warning!
The restraint systems have malfunctioned. The air bags or belt
tensioners could be triggered unintentionally or might not be
triggered at all in the event of an accident.
X Drive on with care.
X Visit a qualified specialist workshop immediately. 003F
The red battery
charge indicator
lamp lights up
while the engine
is running. G
Warning!
The battery is not being charged. Possible causes are a defective
alternator or a torn poly-V-belt.
X Stop the vehicle as soon as possible, paying attention to road
and traffic conditions.
X Check the poly-V-belt.
If it is torn: do not drive on. Consult the nearest qualified
specialist workshop.
If it is not damaged: have the vehicle checked at a qualified
specialist workshop. 003F
The red battery
charge indicator
lamp lights up
while the engine
is running. G
Warning!
The battery is faulty.
X Stop the vehicle as soon as possible, paying attention to road
and traffic conditions.
X Do not continue driving under any circumstances.
X Contact a breakdown service, e.g. an authorized Sprinter
Dealer. 0026
The yellow brake
pad wear
indicator lamp
lights up after
the engine is
started or while
the vehicle is in
motion. G
Warning!
The brake pads/linings have reached their wear limit.
X Have the brake pads/linings replaced as soon as possible at a
qualified specialist workshop. Troubleshooting
191Practical advice Z

Problem Possible causes/consequences and
0050 Solutions00B4
The yellow
engine oil level
warning lamp
lights up
repeatedly while
the vehicle is in
motion. There is a malfunction in the engine oil level display.
X
Have the vehicle checked immediately at a qualified specialist
workshop. 0041
The yellow
coolant level
warning lamp
lights up while
the engine is
running. The coolant level is too low.
Never run the engine if the coolant level is too low. The engine
could overheat and be damaged.
X
Stop the vehicle as soon as possible, paying attention to road
and traffic conditions.
X Switch off the engine and let it cool down.
X Add coolant and be sure to observe the warning notes
(Y page 169).
X If you need to add coolant frequently, have the cooling system
checked at a qualified specialist workshop. 00AE
The red coolant
warning lamp
lights up while
the engine is
running. The coolant temperature is too high.
X
Stop the vehicle as soon as possible, paying attention to road
and traffic conditions.
X Consult a qualified specialist workshop. 00AE
The red coolant
warning lamp
lights up while
the engine is
running. The coolant temperature is too high.
If the vehicle is stopped after being subjected to extreme loads
(e.g. driving in mountainous terrain, trailer towing), the coolant
warning lamp may
light up when the ignition is switched on or the
engine is restarted.
X Run the engine for approximately one minute at idling speed.
X Consult a qualified specialist workshop if the coolant warning
lamp remains lit. 00B7
0080
The yellow
reserve fuel
warning lamp
lights up while
driving. The fuel level has fallen into the reserve range.
X
Refuel at the nearest gas station ( Y page 142). Troubleshooting
193
Practical advice Z

Problem Possible causes/consequences and
0050 Solutions0077
US vehicles
only:
The yellow tire
pressure
monitor warning
lamp flashes for
60 seconds and
then remains lit. The tire pressure monitor has malfunctioned.
X
Have the tire pressure monitor and the wheels checked at a
qualified specialist workshop. 00BA
The yellow water
separator
indicator lamp
lights up when
the ignition is
started. The water that has collected in the water separator has reached
the maximum level.
X
Drain the water separator ( Y page 221).00BD
The yellow
washer fluid
level indicator
lamp for the
windshield
washer/
headlamp
cleaning system
lights up after
the engine is
started or while
the vehicle is in
motion. The water level is too low.
X
Top up washer fluid ( Y page 171).0082
The red seat belt
warning lamp
lights up for
approximately
six seconds
when the key is
turned to
position 2 in the
ignition lock.
A warning tone
also sounds. The warning lamp is to remind you to fasten your seat belt.
X
Fasten seat belt (Y page 34).196
TroubleshootingPractical advice

Problem Possible causes/consequences and
0050 Solutions0055
The yellow bulb
indicator lamp
lights up when
the key is
turned
to position 2 in
the ignition lock. A bulb in the exterior lighting (with the exception of the front
position lamps and trailer lighting) is defective
6
.
X Change defective bulbs as soon as possible ( Y page 233).003E
The yellow door
indicator lamp
lights up while
you are driving. The vehicle is moving without all doors or the hood being closed.
X
Close the doors or hood. Notes on display messages
G
Warning
No messages can be displayed if the
instrument cluster and/or the display fails.
You will then not be able to see information
about the vehicle status, such as speed and
outside temperature, warning/indicator
lamps and display messages or the failure of
systems. Handling characteristics may be
affected. Adapt your speed and driving style
accordingly.
Immediately consult a qualified specialist
workshop. The qualified specialist workshop
must have the necessary specialist
knowledge and tools to carry out the work
required. We recommend an authorized
Sprinter Dealer for

this purpose. In particular,
all work relevant to safety or on safety-related
systems must be carried out at a qualified
specialist workshop. G
Warning
The operating safety of your vehicle could be
jeopardized if maintenance work is carried
out incorrectly. As a result, you could lose
control of the vehicle and cause an accident.
In addition, the

safety systems may no longer be able to protect you or others as they are
designed to do.
Always have
maintenance

work carried out at
a qualified specialist workshop. The qualified
specialist workshop must have the necessary
specialist knowledge and tools to carry out
the work required. We recommend visiting an
authorized Sprinter Dealer. In particular, work
relevant to safety or on safety-related
systems must be carried out at a qualified
specialist workshop.
i If you turn the key to position 2 in the
ignition lock, all warning/indicator lamps
(except the turn signal indicator lamps) and
the display are activated. Please make sure
that they are working properly before
commencing a journey.
Vehicles without steering wheel
buttons Warnings, malfunctions or additional
information may
also

be shown in the display.
The following tables show all the display
messages. For certain display messages, a
warning tone or a continuous tone will also
sound.
6 The lamp failure

indicator may, depending on equipment, be omitted for all lamps with the exception of turn
signals. Troubleshooting
197
Practical advice Z

Display messages Possible causes/consequences and
0050 Solutions0065
Brake force
distribution G
Warning!
EBD has been deactivated due to undervoltage.
The battery might not be charging.
The rear wheels
could lock sooner than expected when you apply
the brakes.
X Pull over immediately, paying attention to road and traffic
conditions.
X Do not continue driving.
X Visit a qualified specialist workshop. 0065
Brake force
distribution Visit
workshop G
Warning!
EBD has malfunctioned.
The rear wheels
could lock sooner than expected when you apply
the brakes.
X Pull over immediately, paying attention to road and traffic
conditions.
X Do not continue driving.
X Consult a qualified specialist workshop. 0066
Parking brake
Release brake A warning tone also sounds.
You are driving with the parking brake applied.
X
Release the parking brake ( Y page 112).0082
Seatbelt sys.
Visit workshop G
Warning!
The belt system has malfunctioned.
X Visit a qualified specialist workshop as soon as possible. 00AE
Coolant Stop,
turn
engine off The coolant temperature is too high.
X
Pull over immediately, paying attention to road and traffic
conditions.
X Consult a qualified specialist workshop. 00AE
Coolant Stop,
turn
engine off The coolant temperature is too high.
If the vehicle is stopped after being subjected to extreme loads
(e.g. driving in mountainous terrain, trailer towing, etc.), this
display message may be shown when the ignition is switched on
or the engine is restarted.
X
Run the engine for approximately one minute at idling speed.
X Consult a qualified specialist workshop if the display message
continues to be shown.206
Troubleshooting
Practical advice

Display messages Possible causes/consequences and
0050 Solutions0055
Low beam left The left-hand low beam is faulty
7
.
X Halogen headlamps: replace the bulbs as soon as possible
(Y page 233).
X Bi-Xenon headlamps: consult a qualified specialist workshop
as soon as possible. 0055
Low beam right The right-hand low beam is faulty
7
.
X Halogen headlamps: replace the bulbs as soon as possible.
(Y page 233)
X Bi-Xenon headlamps: consult a qualified specialist workshop
as soon as possible. 0055
Cornering lt. left The left-hand cornering light is faulty
7
.
X Visit a qualified specialist workshop as soon as possible. 0055
Cornering lt.
right The right-hand cornering light is faulty
7
.
X Visit a qualified specialist workshop as soon as possible. 0055
Lights on
automatic. Remove
key The automatic headlamp feature is active: the light switch is in the
005A position and you have forgotten to remove the key.
X
Remove the key from the ignition lock. 0055
Turn signal left The left-hand turn signal is faulty.
X
Replace the bulb as soon as possible (Y page 233). 0055
Turn signal right The right-hand turn signal is faulty.
X
Replace the bulb as soon as possible (Y page 233). 0055
Brake lamp left The left-hand brake lamp is faulty
7
.
X Replace the bulb as soon as possible (Y page 233). 0055
Brake lamp right The right brake lamp is faulty
7
.
X Replace the bulb as soon as possible (Y page 233). 0055
Third brake lamp The high-mounted brake lamp is faulty
7
. This display message will
only appear if all LEDs have failed.
X Visit a qualified specialist workshop as soon as possible. 7
Depending on the equipment, the bulb-failure indicator may not be featured for any lamps other than the
turn signals. Troubleshooting
209
Practical advice Z

Warning tones
G
Warning
The operating safety of your vehicle could be jeopardized if maintenance work is carried out
incorrectly. As a
result, you could lose control of the vehicle and cause an accident. In addition,
the safety systems may no longer be able to protect you or others as they are designed to do.
Always have maintenance work carried out at a qualified specialist workshop. The qualified
specialist workshop must have the necessary specialist knowledge and tools to carry out the
work required. We recommend visiting an authorized Sprinter Dealer. In particular, work relevant
to safety or on safety-related systems must be carried out at a qualified specialist workshop. Problem Possible causes/consequences and
0050 SolutionsThe anti-theft alarm
system is suddenly
triggered. You opened
the vehicle using the key without first deactivating the
anti-theft alarm system.
X Press the 0036 or 0037 button on the remote control.
or
X Insert the key into the ignition lock.
The anti-theft alarm system is deactivated. A warning tone sounds. A message is shown in the display.
X
Observe the information for the messages (Y page 197).
A warning tone sounds. You are driving with the parking brake applied.
X
Release the parking brake ( Y page 112).
A warning tone sounds. You have opened the driver's door and forgotten to switch off the
lights.
X Turn the light switch to 0027. A warning tone sounds.
G
Warning!
You have not fastened your seat belt.
X Fasten your seat belt ( Y page 32).Engine
G
Warning
The operating safety of your vehicle could be jeopardized if maintenance work is carried out
incorrectly. As a

result, you could lose control of the vehicle and cause an accident. In addition,
the safety systems may no longer be able to protect you or others as they are designed to do.
Always have maintenance work carried out at a qualified specialist workshop. The qualified
specialist workshop must have the necessary specialist knowledge and tools to carry out the
work required. We recommend visiting an authorized Sprinter Dealer. In particular, work relevant
to safety or on safety-related systems must be carried out at a qualified specialist workshop. 212
Troubleshooting
Practical advice

Problem Possible causes/consequences and
0050 SolutionsThe engine does not
start.
The starter motor can
be heard. There is air in the fuel system.
X
Turn the key back to position 0 in the ignition lock before
attempting to start the engine again.
X Start the engine again.
Please bear in
mind that lengthy and frequent starting attempts
will drain the battery.
If the engine does not start after several attempts:
X Consult a qualified specialist workshop. The engine does not
start.
The starter motor can
be heard. The reserve
fuel warning lamp is lit
and the
fuel

gauge is at
0. The fuel tank has been run dry.
X
Refuel the vehicle.
X Bleed the fuel system . The engine does not
start.
The starter motor
cannot be heard.
The
00BB yellow engine
diagnostic lamp and
the yellow DEF
indicator lamp 00E48
lights up. The exhaust gas aftertreatment is faulty, an emission-relevant
malfunction has occurred or the DEF reserve has been used up.
The engine management prevents the engine from starting.
This malfunction or malfunction can damage the exhaust gas
aftertreatment.
X
Observe the messages in the display:
R
on vehicles without steering-wheel buttons (Y page 199)
R on vehicles with steering-wheel buttons (Y page 202) and
(Y page 204). The engine does not
start.
The starter motor
cannot be heard. The battery isolating switch is switched off.
X
Switch on the power supply ( Y page 88).The engine does not
start.
The starter motor
cannot be heard. The on-board voltage is too low (the battery is too weak or
discharged).
X
Jump-start the vehicle (Y page 247).
If the engine does not start despite attempts to jump-start it:
X Consult a qualified specialist workshop. 8
Only vehicles without steering-wheel buttons. Troubleshooting
213
Practical advice Z

Driving systems
G
Warning
The operating safety of your vehicle could be jeopardized if maintenance work is carried out
incorrectly. As a
result, you could lose control of the vehicle and cause an accident. In addition,
the safety systems may no longer be able to protect you or others as they are designed to do.
Always have maintenance work carried out at a qualified specialist workshop. The qualified
specialist workshop must have the necessary specialist knowledge and tools to carry out the
work required. We recommend visiting an authorized Sprinter Dealer. In particular, work relevant
to safety or on safety-related systems must be carried out at a qualified specialist workshop. Problem Possible causes/consequences and
0050 SolutionsOnly the red segments
in the PARKTRONIC
warning

displays are

lit.
A warning tone also
sounds for
approximately two
seconds.
PARKTRONIC is
deactivated after
approximately 20
seconds.
The indicator lamp on
the 0069 switch lights
up and the red
segments in the
PARKTRONIC warning
display go out. PARKTRONIC has malfunctioned and has switched itself off.
When you press the
0069 switch, the red segments in the
PARKTRONIC
warning displays

light up again and the warning tone
sounds for approximately two seconds.
X Have PARKTRONIC checked as soon as possible at a qualified
specialized workshop. The PARKTRONIC
warning displays
implausible distances.
For example, all the
segments may be lit
even though
there

is no
obstacle present. The PARKTRONIC sensors are dirty or iced up.
X
Clean the PARKTRONIC sensors ( Y
page 163).
X Turn the key to position 2 again in the ignition lock. The PARKTRONIC
warning displays
implausible distances.
For example, all the
segments may be lit
even though
there

is no
obstacle present. An external radio or ultrasonic source may be causing
interference.
X
Check PARKTRONIC functions in a different location. Troubleshooting
215
Practical advice Z