steering wheel Mercury Villager 1996 Owner's Manuals
[x] Cancel search | Manufacturer: MERCURY, Model Year: 1996, Model line: Villager, Model: Mercury Villager 1996Pages: 396, PDF Size: 3.67 MB
Page 28 of 396
26
*
[SR13306(ALL)11/95]
The force of the rapidly inflating passenger air bag could push
the top of the rear-facing seat against the vehicle seatback,
armrests or console. Rear-facing infant seats must always be
secured in the rear seat.
*
[SR13307(ALL)07/95]
RWARNING
Do not place objects or mount equipment on or near the
air bag cover on the steering wheel or in front seat areas
that may come in contact with a deploying air bag.
Failure to follow this instruction may increase the risk of
personal injury in the event of a collision.
*
[SR13308(ALL)07/95]
For further information about the proper mounting of
equipment in the front seat of this vehicle, please refer to Ford's
brochure entitledSome Important Information About Air Bag
Supplemental Restraint Systemwhich can be obtained by calling
Helm Inc. at 1-800-782-4356. Ask for brochure FPS-8602.
*
[SR13309(ALL)08/95]
For additional important safety information on the proper use of
seat belts, child seats, and infant seats, please read the other
sections of this chapter of the Owner Guide, especially sections
entitledSafety Belts for ChildrenandSafety Seats for Children.
%*
[SR13310(ALL)01/95]
How the Air Bag Supplemental Restraint System
Operates
*
[SR13315(ALL)06/95]
The Air Bag Supplemental Restraint System consists of the
driver and passenger air bags, impact sensors, a system
diagnostic module, a readiness light and tone, and the electrical
wiring which connects the components.
*
[SR13320(ALL)06/95]
The driver air bag is in the center of the steering wheel. The
front passenger seat air bag is located in the center of the
instrument panel ledge above the glove compartment. Both air
bags are designed to stay out of sight until they are activated.
File:03vxsrn.ex
Update:Wed Jun 5 12:21:10 1996
Page 59 of 396
57
Starting Your Villager
*
[ST02400(ALL)03/95]
Ignition
*
[ST02500(ALL)01/95]
Understanding the Positions of the Ignition
[ST02600(ALL)06/95]
Your vehicle's ignition has four positions. They are:
*
[ST02700(ALL)06/95]
13-1/2 pica
art:0040047-D
The ignition positions
*
[ST02800(ALL)01/93]
ON allows you to test your vehicle's warning lights to make
sure they work before you start the engine. The key returns to
the ON position once the engine is started and remains in this
position while the engine runs.
[ST02900(ALL)06/95]
START cranks the engine. Release the key once the engine starts
so that you don't damage the starter. The key should return to
the ON position when you release it.
[ST03000(ALL)06/95]
OFF/LOCK allows you to shut off the engine and all accessories
and locks the gearshift lever. Removing the key then locks the
steering wheel.
File:04vxstn.ex
Update:Mon Jun 3 08:20:06 1996
Page 60 of 396
58
[ST03200(ALL)01/93]
ACCESSORY allows you to operate some of your vehicle's
electrical accessories while the engine is not running. For
example, you can use ACCESSORY to turn on the radio,
windshield wipers, or operate the cigarette lighter without
starting the engine.
%*
[ST03300(ALL)03/95]
Ignition Key Chime
[ST03400(ALL)02/95]
The chime will sound if you open the driver's door while the
key is in the ignition. Never leave your vehicle unattended with
the key in the ignition.
%*
[ST03500(ALL)02/95]
Removing the Key From the Ignition
[ST03600(ALL)06/95]
OFF/LOCK is the only position that allows you to remove the
key from the ignition. The LOCK feature helps to protect your
vehicle from theft, because it also locks the steering wheel and
the gearshift lever when the key is removed.
%*
[ST03700(ALL)01/93]
If your key is stuck in the LOCK position, and you are unable
to turn it, move your steering wheel left or right until the key
turns freely.
*
[ST03800(ALL)01/93]
To remove your key from the ignition:
*
[ST03900(ALL)05/95]1.
Put the gearshift lever in P (Park).
*
[ST04000(ALL)02/95]2.
Set the parking brake fully.
*
[ST04100(ALL)03/95]3.
Turn the ignition key to LOCK.
*
[ST04200(ALL)03/95]4.
Remove the key.
*
[ST04300(ALL)06/95]
RWARNING
When you leave your vehicle, place the gearshift lever in
P (Park). Set the parking brake fully, and shut off the
engine. Never park your vehicle in N (Neutral). If you do
not take these precautions, your vehicle may move
suddenly and injure someone.
File:04vxstn.ex
Update:Mon Jun 3 08:20:06 1996
Page 62 of 396
60
*
[ST05200(ALL)03/95]3.
Make sure that the gearshift is in P (Park) and the parking
brake is set before you turn the key.
[ST05400(ALL)04/95]4.
Test the warning lights on the instrument cluster to make
sure they work. Refer to theWarning Lights and Gauges
chapter.
*
[ST05700(ALL)02/95]
Starting Your Engine
*
[ST05800(ALL)02/95]
To start your engine:
*
[ST05900(ALL)05/95]1.
Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
*
[ST06000(ALL)01/93]2.
Keep your foot on the brake pedal and turn the ignition key
to ON.
*
[ST06100(ALL)03/95]3.
DO NOT depress the accelerator pedal when starting your
engine. DO NOT use the accelerator while the vehicle is
parked.
*
[ST06200(ALL)02/95]4.
Turn the key to the START position (cranking) until the
engine starts. Allow the key to return to the ON position
after the engine has started.
*
[ST06300(ALL)02/95]
If you have difficulty in turning the key, rotate the steering
wheel slightly because it may be binding.
*
[ST06900(ALL)04/94]
For a cold engine:
*
[ST07000(ALL)06/95]
n
At temperatures10ÊF (-12ÊC) andbelow:If the engine does
not start infifteen (15) secondson the first try, turn the key
to OFF, wait approximately ten (10) seconds so you do not
flood the engine, then try again.
*
[ST07100(ALL)04/95]
n
At temperaturesabove10ÊF(-12ÊC):If the engine does not
start infive (5) secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you do not flood the
engine, then try again.
File:04vxstn.ex
Update:Mon Jun 3 08:20:06 1996
Page 122 of 396
123
Steering Column Controls
*
[SC00900(ALL)01/95]
The controls on the steering column and wheel are designed to
give you easy access to the controls while you are driving.
*
[SC01000(ALL)01/93]
Turn Signal Lever
*
[SC01100(ALL)01/95]
You can use the turn signal lever on the left side of the steering
column to:
*
[SC01200(ALL)01/93]
n
operate the turn signals.
*
[SC01300(ALL)01/93]
n
turn the headlamps to high beam.
*
[SC01400(ALL)01/93]
n
flash the headlamps.
*
[SC01500(ALL)01/93]
n
turn the windshield wipers and washer on/off.
*
[SC01600(ALL)01/95]
Turn Signals
[SC01700(ALL)02/95]
Move the lever up to signal a right turn. Move it down to
signal a left turn. The corresponding indicator light in the
instrument cluster will flash.
*
[SC01900(ALL)11/93]
7-1/2 pica art:0040085-D
The turn signal lever
[SC02000(ALL)02/95]
If the turn signal stays on after you turn, move the lever back
to the center (off) position.
[SC02100(ALL)02/95]
For lane changes, move the lever far enough to signal but not to
latch. The lever will return to the off position when you release
it.
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996
Page 126 of 396
Steering Column Controls
127
[SC04700(ALL)05/95]
Tilt Steering
[SC04850(ALL)02/95]
RWARNING
Never adjust the steering wheel when the vehicle is
moving. You could lose control of the vehicle and injure
someone.
[SC04900(ALL)02/95]
17-1/2 pica art:0040089-E
Tilt release lever location
[SC05000(ALL)06/95]
To change the position of the steering column, pull the release
lever on the column down. Move the steering wheel to the
desired position and raise the lever to lock the steering wheel in
place.
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996
Page 127 of 396
128
*
[SC05600(ALL)03/91]
Speed Control (If equipped)
[SC05603(ALL)02/95]
The speed control system allows your vehicle to maintain a set
speed above 30 mph (48 km/h) without keeping your foot on
the accelerator pedal.
[SC05605(ALL)01/93]
Avoid using the speed control when driving under the
following conditions:
[SC05610(ALL)07/93]
n
when it is not possible to keep the vehicle at a set speed
[SC05620(ALL)07/93]
n
in heavy traffic or in traffic that varies in speed
[SC05630(ALL)08/93]
n
on winding or hilly roads
[SC05640(ALL)07/93]
n
on slippery roads (rain, snow, ice, etc.)
[SC05650(ALL)09/93]
n
in very windy areas
[SC05800(ALL)09/93]
To activate the speed control, push the main switch (CRUISE
CONT. ON); the switch is located in the group of controls to
the left of the steering wheel. The indicator light on the switch
will come on.
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996
Page 128 of 396
Steering Column Controls
129
[SC05900(ALL)09/93]
13-1/2 pica
art:0040091-B
Speed control main switch location
[SC06000(ALL)01/93]
Setting the Speed Control
[SC06100(ALL)04/95]
To set the speed control, accelerate your vehicle to the desired
speed (at least 30 mph [48 km/h]), push and release the
COAST/SET button on the left side of the steering wheel. The
CRUISE light in the instrument cluster will come on. Take your
foot off the accelerator pedal. Your vehicle will maintain the set
speed.
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996
Page 129 of 396
130
[SC06200(ALL)06/95]
24 pica art:0040090-F
Speed control buttons on the steering wheel
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996
Page 130 of 396
Steering Column Controls
131
%*
[SC06300(ALL)06/95]
Accelerating With the Speed Control Operating
[SC06400(ALL)01/93]
To pass another vehicle while the speed control is activated,
press the accelerator pedal. When you release the pedal, the
vehicle will return to the previously set speed.
[SC06500(ALL)01/93]
Driving Uphill or on a Steep Grade
[SC06600(ALL)01/93]
The vehicle may not maintain the set speed when going up or
down steep hills. If this happens, drive without the speed
control.
[SC06700(ALL)07/93]
When driving uphill, especially with a heavy load, you may
notice your speed decreasing, even if you have the speed
control set. If the speed drops more than 8 mph (13 km/h), it is
normal for the automatic speed control feature to be cancelled.
You may need to help your vehicle maintain the selected speed
by driving without the speed control when driving up steep
grades.
[SC06800(ALL)01/93]
Cancelling the Speed Control
[SC06900(ALL)02/94]
To cancel the preset speed, follow one of these three methods:
[SC07000(ALL)04/95]
n
Push the CANCEL button on the left side of the steering
wheel; the CRUISE light will go out.
[SC07100(ALL)01/93]
n
Tap the brake pedal; the CRUISE light will go out.
[SC07200(ALL)09/93]
n
Press the main OFF switch to the left of the steering wheel.
Both the CRUISE CONT. ON switch indicator and the
CRUISE light in the instrument cluster will go out.
[SC07300(ALL)09/93]
If you unintentionally press the brake pedal while pushing the
RESUME/ACCEL button to reset the cruising speed, press the
OFF switch once and then reactivate the system by pressing the
CRUISE CONT. ON switch.
[SC07400(ALL)01/93]
The speed control will automatically be canceled if the vehicle
slows down below approximately 8 mph (13 km/h).
File:07vxscn.ex
Update:Mon Jun 3 14:47:35 1996