engine Mercury Villager 1998 s Owner's Guide

NOTE: Your vehicle has an interlock that prevents you from
shifting out of P (Park) unless your foot is on the brake
pedal.
If the engine does not start after two attempts:
1. Turn the ignition key to the OFF position.
2. Press the accelerator all the way to the floor and hold it.
3. Turn the ignition key to the START position.
4. Release the ignition key when the engine starts.
5. Release the accelerator gradually as the engine speeds up.
If the engine still does not start, the fuel pump shut-off switch may
have been activated. For directions on how to reset the switch
seeFuel Pump Shut-Off Switchin the index.
A computer system controls the engine's idle speed. When you
start your vehicle, the engine's idle speed normally runs high.
These faster engine speeds will make your vehicle coast
slightly faster than its normal idle speed. It should, however,
slow down after a short time. If it does not, have the idle speed
checked.
If the engine idle speed does not slow down automatically, do
not allow your vehicle to idle for more than 10 minutes. Have the
vehicle checked.
WARNING
Extended idling at high engine speeds can produce very
high temperatures in the engine and exhaust system,
creating the risk of fire or other damage.
Starting
209

WARNING
Do not park, idle, or drive your vehicle in dry grass or
other dry ground cover. The emission system heats up the
engine compartment and exhaust system, which can
start a fire.
If you consistently start your vehicle in subzero temperatures, use
an engine block heater (if your vehicle has this option). If your
vehicle does not have this option, it is available thru your dealer.
Engine Block Heater (Canada only)
Engine block heaters are strongly recommended if you live in a
region where temperatures reach ±10É F (±23É C) or below. An
engine block heater warms the engine coolant, which improves
starting, warms up the engine faster, and allows the heater-defrost
system to respond more quickly.
WARNING
To prevent electrical shock, do not use your heater with
ungrounded electrical systems or two-pronged (cheater)
adapters.
For best results, plug the heater in at least three hours before you
start your vehicle. Using the heater for longer than three hours
will not damage the engine, so you can leave it plugged in all night
to start your vehicle the following morning.
What To Do If The Engine Does Not Start
Fuel Pump Shut-Off Switch
If the engine cranks but does not start or does not start even after
a small collision, the fuel pump shut-off switch may have been
activated. The shut-off switch is a device intended to stop the fuel
pump when your vehicle has been involved in a substantial
jolt. Refer to theRoadside emergenciessection for more information.
210

Once the shut-off switch is activated, you must reset the switch
by hand before you can start your vehicle.
The fuel pump shut-off switch reset button is located below the
hood release handle.
WARNING
If you see or smell fuel, do not reset the switch or try to
start your vehicle. Have all the passengers get out of the
vehicle and call the local fire department or a towing
service.
If your engine cranks, but does not start after a collision:
1. Turn the key in the ignition to the OFF position.
2. Check under the vehicle for leaking fuel.
3. If you do not see or smell fuel, push the fuel pump shut-off
reset button down. If the red button is already set, you may
have a different mechanical or electrical problem.
4. Turn the ignition key to the ON position for a few seconds,
then turn it to the OFF position.
Fuel pump shut-off switch reset button location
Starting
211

5. Check under the vehicle again for leaking fuel. If you see or
smell fuel, do not start your vehicle again. If there is no
fuel, you can try to start your vehicle again.
6. Check all vehicle warning lights before driving your vehicle.
Guarding Against Exhaust Fumes
Carbon monoxide, although colorless and odorless, is present in
exhaust fumes. Take precautions to avoid its dangerous
effects.
WARNING
Do not start your vehicle in a closed garage or in other
enclosed areas. Exhaust fumes can be toxic. Always open the
garage door before you start the engine.
WARNING
If you ever smell exhaust fumes of any kind inside your
vehicle, have your dealer inspect and fix your vehicle
immediately. Do not drive if you smell exhaust fumes.
These fumes are harmful and could kill you.
Have the exhaust and body ventilation systems checked by a
qualified technician whenever:
myour vehicle is raised for service
mthe sound of the exhaust system changes
myour vehicle has been damaged in an accident
Improve your ventilation by keeping all air intake vents clear of
snow, leaves, and other objects.
If the engine is idling while you are stopped in an open area for
long periods of time, open the windows at least one inch (2.5
cm). Also, adjust the heating or air conditioning system to bring
in outside air.
212

Read the sectionClimate Control Systemsfor instructions on
bringing fresh outside air into your vehicle. Refer to the Index.
Removing the Key From the Ignition
OFF/LOCK is the only position that allows you to remove the
key from the ignition. The LOCK feature helps to protect your
vehicle from theft, because it also locks the steering wheel
and the gearshift lever when the key is removed.
If your key is stuck in the LOCK position, and you are unable to
turn it, move your steering wheel left or right until the key
turns freely in the lock.
To remove your key from the ignition:
1. Put the gearshift lever in P (Park).
2. Set the parking brake fully.
3. Turn the ignition key to LOCK.
4. Remove the key.
WARNING
When you leave your vehicle, place the gearshift lever in
P (Park). Set the parking brake fully, and shut off the
engine. Never park your vehicle in N (Neutral). If you do
not take these precautions, your vehicle may move
suddenly and injure someone.
WARNING
Do not leave children, unreliable adults, or pets
unattended in your vehicle.
Starting
213

During ABS activation, a mechanical noise may be heard as the
ABS cycles. This is normal ABS operation.
Anti-lock brake system (ABS)
On vehicles equipped with an anti-lock braking system (ABS), a
noise from the hydraulic pump motor and pulsation in the
pedal may be observed during ABS braking events. Pedal pulsation
coupled with noise while braking under panic conditions or on
loose gravel, bumps, wet or snowy roads is normal and indicates
proper functioning of the vehicle's anti-lock brake system. If
the vehicle has continuous vibration or shudder while braking,
felt mainly in the steering wheel, the vehicle most likely needs
service.
The ABS system has self-check capabilities. The system turns on
the ABS warning light each time you start the engine. After
the engine is started and the ABS warning light turns off, the system
performs another test the first time the vehicle reaches 4 mph
(6 km/h). A mechanical noise may be heard as the ABS system
performs a self test. This is a normal part of the self test
feature. If a malfunction is found during this check, the ABS
warning light will come on.
You should always be careful when braking, even if your vehicle
has the ABS system. Heavy braking on roads with loose
surfaces such as snow or gravel, or roads with severe pavement
irregularities could also cause you to lose control of your
vehicle.
WARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system
checked by a qualified service technician as soon as
possible.
216

The parking brake is not designed to stop a moving vehicle, but
you can use the parking brake to stop your vehicle in an
emergency if the service brakes fail. However, since the parking
brake does not stop your vehicle as quickly as the normal
brakes, the stopping distance will increase greatly.
Steering Your Vehicle
Your vehicle has power steering. Power steering uses energy
from the engine to help steer your vehicle.
If the amount of effort needed to steer your vehicle changes at a
constant vehicle speed, have the power steering system
checked. If the power steering system breaks down (or if the
engine is turned off), you can steer the vehicle manually but it takes
more effort.
Never hold the steering wheel in the extreme right or left
position for more than five seconds if the engine is running. This
can damage the power steering pump.
NOTE: After any severe impact such as striking large potholes,
sliding into curbs on icy roads, or a collision involving
the front end, have the front suspension and
steering checked for possible damage.
220

Shift-lock Safety Feature
Your vehicle has a special shift-lock safety feature which prevents
you from shifting out of P (Park) without the brake pedal
depressed. To shift the transaxle out of the P (Park) position, the
ignition must be in the ON position and your foot must be
pressing on the brake pedal.
If the shift lever cannot be moved from the P (Park) position with
the brake pedal depressed:
1. Shut the engine off and remove the ignition key.
2. Apply the parking brake.
3. Reinsert the ignition key and turn it to the first position (OFF).
4. Depress the brake pedal, move the gearshift lever to N
(Neutral) and start the engine.
If you need to shift out of P (Park) by using the alternate
procedure described above, it is possible that a fuse has blown
and that your brakelamps may also not be functional. Please refer
to the chapter titledRoadside Emergenciesin this Owner Guide
for instructions on checking and replacing fuses.
WARNING
DO NOT DRIVE YOUR VEHICLE UNTIL YOU VERIFY
THAT THE BRAKELAMPS ARE WORKING.
Backing Up
Before shifting into or out of R (Reverse), you should always
come to a complete stop.
222

Driving
When to use D (Overdrive)
Overdrive is the normal driving position. When the gearshift
lever is placed in (D) Overdrive, and the Overdrive Off button has
not been pressed, the vehicle will automatically upshift to
second, third and fourth gears. The transaxle will shift into the
correct gear when the right speed is reached.
When to use D (Drive Ð with the Overdrive Off button
activated)
You will notice that there is only one drive position on your
gearshift selection indicator (instead of Drive and Overdrive). You
will find a button labeled OVERDRIVE OFF/ON located on
the gearshift lever. Push in the button on the end of the lever and
the O/D OFF light in the instrument cluster will illuminate.
With the O/D OFF light illuminated, the transaxle will operate in
first, second and third gears and will not shift into fourth gear.
Operating in Drive (O/D OFF) provides more engine braking than
Overdrive for descending hills, or city driving.
To return the transaxle to the normal Overdrive operation,
press the OVERDRIVE OFF/ON button again. Use this button to
select Overdrive or Overdrive Off whenever you drive your
vehicle.
NOTE: Overdrive will not engage until the engine has fully
warmed up.
The OVERDRIVE OFF/ON button
Driving
223

The transaxle will be in the ªoverdrive onº mode when the
vehicle is started even if the O/D OFF mode was selected when
the vehicle was last shut off.
If your vehicle is on an extremely slippery surface, the Electronic
Transaxle Control Module may receive a signal indicating a
rapid increase or decrease in wheel speed. If the module detects
this condition, it will limit the transaxle operation to Third
gear and Reverse. This reduces tire slippage and protects the
transaxle. The transaxle will operate normally in Reverse, but will
lack power during acceleration in Drive. If this happens, stop
your vehicle as soon as possible and turn the ignition off for 3
seconds. Restart the vehicle. If the condition still exists, contact your
dealer as soon as possible.
NOTE: If the O/D OFF indicator light is flashing on and off
repeatedly when the vehicle is started, there is a
transaxle electronic system malfunction. Contact your
dealer as soon as possible.
When to use 2 (Second)
Use Second (2) when driving on slippery roads or to provide
additional engine braking on downgrades. This position provides
Second gear operation only. Do not exceed 68 mph (108 km/h)
in this position.
When to use 1 (First)
Use First (1) to provide maximum engine braking on steep
downgrades. Upshifts from First can be made by manually shifting
to Second (2) or Overdrive (D). First (1) gear provides only first
gear operation. If you select First while driving at higher speeds, the
transaxle will shift to Second (2), and then shift back to First
(1) after the vehicle decelerates to the proper speed. Do not exceed
35 mph (56 km/h) in this position.
224