light Mercury Villager 1998 s Workshop Manual

The Air Bag Supplemental Restraint System consists of:
mdriver and passenger air bag modules (which include the
inflators and air bags),
mone or more impact and safing sensors,
ma system diagnostic module,
ma readiness light,
mand the electrical wiring which connects the components.
The diagnostic module monitors its own circuits, the air bag
electrical system, the air bag readiness light, the air bag power and
the air bag inflators.
Inflated driver side air bag
148

Determining If System Is Operational
The Air Bag Supplemental Restraint System uses a readiness light
to indicate the condition of the system. The readiness light is in
the instrument cluster. When you turn the ignition key to ON, this
light will illuminate for approximately six (6) seconds and then
turn off. This indicates that the system is operating normally.
NOTE: Routine maintenance of the air bag system is not
required.
A problem with the system is indicated by one or more of the
following:
mthe readiness light will either flash or stay lit,
mthe readiness light will not light immediately after ignition is
turned on.
Inflated passenger side air bag
Seating and Safety Restraints
149

4. Place your hand under the seat cushion and tip the front of the
seat upward slightly. Slide the seat rearward to release the seat
from its anchor position.
5. Two people should lift the seat and remove it from the vehicle.
6. Replace any floor mats that were removed.
If you decide to move the three-passenger bench seat forward to
the second row position, passengers riding in the seat will use
the second row safety belts.
The floor latch levers
Adjustable Rear Seating
185

Installing the Two-Passenger Bench Seat
To replace the bench seat in its original position:
1. Make sure the area around the floor anchor positions is free
from obstruction.
2. With the seatback folded down, two people should lift the seat
into the vehicle.
3. Place the seat slightly behind the floor anchor positions and
catch the rear leg anchors into each anchor position.
4. Press down on the front of the seat to secure the front legs to
the two floor latch locks. Place the seatback in the upright
position.
5. Try to move the seat to be sure that it is securely fastened.
6. Always reattach the tongue into the auxiliary buckle mounted
to the sliding door side of the seat.
Labels have been provided on the side of the seat to remind you
of important safety precautions.
7. Replace any floor mats that were removed.
WARNING
Keep foreign objects out of the floor anchors. Objects in
the floor anchors could prevent front and rear seat legs from
engaging properly.
WARNING
Before sitting in the removable seats, make sure that the
seat legs are securely attached by the floor anchors.
186

3. Place your hand under the seat cushion and tip the front of the
seat upward slightly. Slide the seat rearward to release the seat
from its anchor position.
4. Two people should lift the seat and remove it from the vehicle.
5. Replace any floor mats that were removed.
NOTE: The captain seats are not interchangeable due to the
locations of the floor latch levers. Each seat must be
reinstalled in its original position. In addition, the seat
behind the driver seat only has one arm rest.
The removable inside captain seat
Adjustable Rear Seating
191

Installing the Removable Captain Seats
To position the captain seats back in their original positions:
1. Make sure the area around the floor anchor positions is free
from obstruction.
2. With the seatback folded down, two people should lift the seat
into the vehicle.
3. Place the seat slightly behind the floor anchor positions and
catch the rear leg anchors into each anchor position.
4. Press down on the front of the seat to secure the front legs to
the two floor latch locks. Place the seatback in the upright
position.
5. Try to move the seat to be sure that it is securely fastened.
6. Replace any floor mats that were removed.
Labels have been provided on the side of the seats to remind you
of important safety precautions.
WARNING
Keep foreign objects out of the floor anchors. Objects in
the floor anchors could prevent front and rear seat legs from
engaging properly.
WARNING
Before sitting in the removable seats, make sure that the
seat legs are securely attached by the floor anchors.
192

Fuel-Injected Engines
When starting a fuel-injected engine,the most important thing to
remember is to avoid pressing down on the accelerator
before or during starting. Only use the accelerator when you
have problems getting your vehicle started. SeeStarting Your Engine
in this chapter for details about when to use the accelerator
while you start your vehicle.
Starting Your Vehicle
Preparing to Start Your Vehicle
WARNING
Do not start your vehicle in a closed garage or in other
enclosed areas. Exhaust fumes can be toxic. Always open the
garage door before you start the engine.
Before you start your vehicle, always:
1. Make sure you and all your passengers buckle your safety
belts. SeeSafety beltsin the Index for more details.
2. Make sure the headlamps and other accessories are turned off
when starting.
3. Make sure that the gearshift is in P (Park) and the parking
brake is set before you turn the key.
4. Observe the warning lights on the instrument cluster to make
sure they work. Refer to theInstrumentationchapter.
Starting Your Engine
To start your engine:
1. Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
Starting
207

2. Keep your foot on the brake pedal and turn the ignition key to
ON.
3. DO NOT depress the accelerator pedal when starting your
engine. DO NOT use the accelerator while the vehicle is
parked.
4. Turn the key to the START position (cranking) until the engine
starts. Allow the key to return to the ON position after the
engine has started.
If you have difficulty in turning the key, rotate the steering
wheel slightly because it may be binding.
For a cold engine:
mAt temperatures10É F (-12É C) and below:If the engine does
not start infifteen (15) secondson the first try, turn the key
to OFF, wait approximately ten (10) seconds so you do not flood
the engine, then try again.
mAt temperaturesabove 10É F (-12É C):If the engine does not
start infive (5) secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you do not flood the
engine, then try again.
For a warm engine:
mDo not hold the key in the START position for more thanfive
(5) secondsat a time. If the engine does not start within five
(5) seconds on the first try, turn the key to the OFF position. Wait
a few seconds after the starter stops, then try again.
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter.
After you start the engine, let it idle for a few seconds.Keep
your foot on the brake pedaland release the parking brake. Put
the gearshift lever in gear, slowly release the brake pedal and
drive away in the normal manner.
208

NOTE: Your vehicle has an interlock that prevents you from
shifting out of P (Park) unless your foot is on the brake
pedal.
If the engine does not start after two attempts:
1. Turn the ignition key to the OFF position.
2. Press the accelerator all the way to the floor and hold it.
3. Turn the ignition key to the START position.
4. Release the ignition key when the engine starts.
5. Release the accelerator gradually as the engine speeds up.
If the engine still does not start, the fuel pump shut-off switch may
have been activated. For directions on how to reset the switch
seeFuel Pump Shut-Off Switchin the index.
A computer system controls the engine's idle speed. When you
start your vehicle, the engine's idle speed normally runs high.
These faster engine speeds will make your vehicle coast
slightly faster than its normal idle speed. It should, however,
slow down after a short time. If it does not, have the idle speed
checked.
If the engine idle speed does not slow down automatically, do
not allow your vehicle to idle for more than 10 minutes. Have the
vehicle checked.
WARNING
Extended idling at high engine speeds can produce very
high temperatures in the engine and exhaust system,
creating the risk of fire or other damage.
Starting
209

5. Check under the vehicle again for leaking fuel. If you see or
smell fuel, do not start your vehicle again. If there is no
fuel, you can try to start your vehicle again.
6. Check all vehicle warning lights before driving your vehicle.
Guarding Against Exhaust Fumes
Carbon monoxide, although colorless and odorless, is present in
exhaust fumes. Take precautions to avoid its dangerous
effects.
WARNING
Do not start your vehicle in a closed garage or in other
enclosed areas. Exhaust fumes can be toxic. Always open the
garage door before you start the engine.
WARNING
If you ever smell exhaust fumes of any kind inside your
vehicle, have your dealer inspect and fix your vehicle
immediately. Do not drive if you smell exhaust fumes.
These fumes are harmful and could kill you.
Have the exhaust and body ventilation systems checked by a
qualified technician whenever:
myour vehicle is raised for service
mthe sound of the exhaust system changes
myour vehicle has been damaged in an accident
Improve your ventilation by keeping all air intake vents clear of
snow, leaves, and other objects.
If the engine is idling while you are stopped in an open area for
long periods of time, open the windows at least one inch (2.5
cm). Also, adjust the heating or air conditioning system to bring
in outside air.
212