window Mercury Villager 1998 Owner's Manuals

You can change the frequency up or down one increment at a
time (FM changes in increments of 200 kHz; AM changes
in increments of 10 kHz) by pressing the ªTUNEº button. To
change frequencies quickly, press andhold downeither the right
or left side of the ªTUNEº button.
Manual tuning adjusts your radio to any allowable broadcast
frequency, whether or not a station is present on that
frequency. (SeeAll About Radio Frequencieslater in this
chapter.)
mUsing the ªSEEKº function
This feature on your radio allows you to automatically select
listenable stations up or down the frequency band. Press the
right
side of the ªSEEKº button to select the next
listenable station up the frequency band. Press the left
side
of the button to select the next listenable station down the
frequency band. By holding the button down, listenable stations
can be passed over to reach the desired station.
mUsing the ªSCANº button to scan radio stations
Pressing the ªSCANº button once enters the scan mode by
stopping on each listenable station for a five-second sampling.
The radio band (AM/FM1/FM2) in the display window
will blink to indicate that the radio is scanning.
To stop the scan mode on the presently sampled station press
the ªSCANº button again.
34

The controls for the climate control systems, headlamps, clock,
radio, rear window washer and wiper, hazard flasher, power mirror
controls, and speed control are all on the instrument panel.
Climate Control Systems
Function Selector Buttons
There are six function selector buttons: OFF, Mix, Defrost, Panel,
Panel/Floor, and Floor. When you press a function selector
button, the indicator light on the button will illuminate. If your
vehicle is equipped with a rear passenger compartment climate
control system, the instrument panel will also include a rear
seat function selector.
mThe OFF button shuts off the air supply to all outlets and
stops all fan operations. Use this setting when driving through
an area where outside air is unpleasant or dusty.
Climate control system panel
56

WARNING
Operating with the function selector control in off or in
the recirculated air mode for extended periods of time in
cold weather can result in fog buildup on interior glass
surfaces.
mThe Mix () button directs approximately equal amounts
of air to the windshield and floor outlets with a small
amount to the side windows.
mThe Defrost (
) button directs air to the windshield and
front side windows with a small amount going to the floor
outlets.
mThe Panel (
) button directs air to the instrument panel
outlets.
mThe Panel/Floor (
) button directs approximately equal
amounts of air to the instrument panel outlets and the floor
outlets.
mThe Floor (
) button directs most of the system's air
supply to the floor outlets with a small amount going to the
windshield and side window defrosters.
Air Outlets
Air intake selector button
The typical air intake selection is outside air. However, for
recirculated air, the air intake selector button may be activated.
When the air intake selector button is activated (indicator light is
on), it prevents the intake of outside air. This is the typical
selection when using the air conditioner (if equipped). It
recirculates interior air for faster cooling. The recirculated air
function also helps to prevent the intake of dusty or unpleasant air.
Controls and Features
57

There are several air outlets on the instrument panel. There are
side outlets near the driver's window and passenger's window, two
center outlets, floor outlets, and windshield outlets. The
direction and amount of air flow from the center and side
instrument panel outlets can be adjusted for personal comfort.
NOTE: Selection of the recirculated air mode under cold and
humid conditions may result in window fogging due to
entrapped humidity within the vehicle. To counteract
this circumstance, switch to the Defrost mode and set fan
speed to 3 or 4. Adjust air temperature to a ªwarmº
instead of ªhotº setting and deactivate the air intake
selector.
Heating Only System (Without air conditioning)
You can heat and ventilate the inside of your vehicle, or defrost
the windshield with the function selector buttons, the fan speed
knob and the temperature control knob.
An additional push-on/push-off air intake selector button
provides for the selection of recirculated inside air (button lighted)
or outside air (button not lighted).
58

To defrost the windshield and side windows:
mPress the Defrost button, turn the temperature control knob to
the WARM (red) area and turn the fan speed knob to the
position of your choice. The recirculated air feature will be
automatically turned off in this setting (outside air will be
provided).
mTo reduce window fogging under extreme conditions, select
defrost and high fan speed while reducing temperature to a
ªwarmº instead of ªhotº setting. Deactivating the air intake
selector may also help dry the interior window surfaces.
To heat and defrost at the same time:
mPress the Mix function selector button, turn the temperature
control knob and the fan speed knob to provide the
temperature and fan speed you prefer. The recirculated air
feature will be automatically turned off in this setting (outside
air will be provided).
Controlling the Temperature in Your Vehicle
mTo ventilate your vehicle with outside air, make sure that the
air intake selector button is set for outside air. Open the
instrument panel registers enough to provide the amount of
air desired for your comfort.
mTo vary the temperature inside your vehicle, move the
temperature control knob toward WARM (red) for warmer
temperatures and toward COOL (blue) for cooler temperatures.
The temperature control knob setting determines the
temperature of the air being discharged from the system in all
operating modes (heating or A/C).
60

Turning on the air conditioner
To cool your vehicle quickly in warm weather:
1. Press one of the function selector buttons (typically Panel, but
Panel/Floor, Floor or Mix can be selected).
2. Turn the temperature control knob to COOL.
3. Press the A/C button. The indicator light on the A/C button
will illuminate.
4. The air intake selector button may be in the outside air mode
or the recirculated air mode. The outside air mode is
recommended for best A/C performance when the vehicle
interior is very warm. As interior air comfort is reached, you
may decide to switch to the recirculated air mode.
5. Turn the fan speed knob to the position of your choice.
6. If your vehicle is equipped with the rear passenger compartment
air conditioning unit, it will be on when the front A/C is on
and the rear climate control lever is set to REAR, 1, 2, 3, or 4.
Refer to the previous section for an explanation of the
heating system.
7. Adjust your instrument panel registers.
8. If the inside of your vehicle is very warm, you may want to
drive for a few minutes with the windows down and the air
conditioner on. This forces most of the hot, stale air out of the
vehicle and allows the air conditioner to cool down the
interior more quickly.
The air conditioner may be used to cool the outside air being
drawn into your vehicle, but using recirculated air is more
economical and cools your vehicle more quickly.
Controls and Features
63

NOTE: For maximum heating and cooling for front seat
passengers, set the rear fan switch to the OFF position.
Automatic Temperature Control System
The control for your Automatic Temperature Control (ATC) is
located at the center of the instrument panel above the radio. The
ATC operates only when the ignition key is turned to the ON
position and the engine is running.
To turn the ATC on, push the AUTOMATIC button or any of the
five airflow function selector buttons:
,,,,
or
.
To turn the ATC off, press the OFF button.
To change the temperature in the display window, select any
temperature between 65É F (18É C) and 85É F (29É C) using
the
TEMPbutton.
Rear seat climate control system panel
Controls and Features
67

if you choose to manually override the airflow location by
selecting one of the function selector buttons, you will also need
to select the A/C button if you desire cool air-conditioned air.
(Your ATC automatically operates the air conditioning [if required]
when you are in the AUTOMATIC mode without illuminating
the A/C button, but the system requires you to manually select the
A/C button if you desire A/C operation when you manually
override airflow location.)
If you want continuous maximum cooling, push the
side of
the TEMP button until 60É F (16É C) shows in the display window.
The ATC will cool at its maximum level and disregard the
60É F (16É C) setting until a warmer temperature is selected. If
you want continuous maximum heating, push the
side of the
TEMP button until 90É F (32É C) shows in the display window.
The ATC will provide maximum heat regardless of the 90É F (32É C)
setting until a cooler temperature is selected.
The display window and the function selector buttons indicate
how the system is operating. The display window shows the
selected temperature and displays AUTO if you are operating
in the AUTOMATIC mode. If you override the automatic mode by
selecting any of the function selector buttons, AUTO no longer
appears in the display window and the appropriate function
selector button(s) illuminate. The display window also
indicates manual (thumbwheel) control of the fan speed when a
is shown.
Automatic Operation
Push the AUTOMATIC button and select the desired
temperature. The selected temperature and AUTO appear in the
display window. The ATC heats or cools to achieve the set
temperature. It is important to note that if the ATC engages your
vehicle's air-conditioning, it will do so automatically without
illuminating the A/C button.
Controls and Features
69

When in AUTOMATIC and weather conditions require heat, air
is sent to the floor. However, a feature is included in the ATC to
prevent blowing cold air to the floor if the engine coolant is
not warm enough to provide heating. Within three or four minutes
(once the engine coolant is warm enough), the fan speed
gradually increases and airflow changes to the floor.
If specific conditions exist (such as window fogging), the five
override buttons allow specific airflow selection. The dial allows
you to adjust the fan speed to suit your needs.
Temperature Selection
TheTEMPbutton on the left side of the control panel is
for temperature selection. The
side lowers the set temperature,
and the
side raises the set temperature. Press and hold
either side of the button to rapidly change the temperature setting
in one degree increments to either 65É F (18É C) or 85É F (29É C).
Then, the set temperature jumps 5É F and stops at either 60É F
(16É C), which is maximum cooling, or 90É F (32É C), which is
maximum heating.
70

Changing the Display Mode (English/Metric)
To switch between the English and Metric display mode, press
the DEFROST and A/C buttons simultaneously while rotating the
fan speed dial upward until it stops moving. After one second,
the display will begin to toggle between English and Metric.
Fan Speed and Thumbwheel
The ATC automatically adjusts the fan speed to the existing
conditions. To control the fan speed yourself, use the thumbwheel
located at the extreme right side of the ATC control panel.
Using the thumbwheel cancels the automatic fan speed control,
and causes a
to appear in the display window. Rotate the
thumbwheel up for HI speeds and down for LO speeds.
To return to automatic fan control, press the AUTOMATIC button.
Airflow Function Selector Buttons
Your ATC has five buttons which allow you to make special
selections for airflow. The buttons are grouped in the middle of
the ATC panel and allow you to determine airflow location.
Pressing any of the function selector buttons illuminates the
button pushed and directs airflow to the appropriate location. The
temperature of the airflow will still be automatically controlled.
Return to fully automatic operation by pushing the AUTOMATIC
button.
Push this button for airflow to the floor and windshield at the
same time. The
indicator light illuminates, and the display
window shows the set temperature. However, the air is not
cooled below the temperature outside of the vehicle regardless of
the temperature setting unless the A/C button is pushed.
Controls and Features
71