flat tire MINI Hardtop 2 Door 2005 User Guide

102
RUN FLAT TIRES
*
NEW WHEELS AND TIRES
If there is a total loss of tire inflation pres
-
sure, 0
psi
/ 0 kPa, or obvious tire damage,
you can gauge the mileage for continued
driving on the basis of the following indica
-
tions:>With a light load:

1 to 2 persons without luggage:

approx. 155
miles
/ 250
km
>With a medium load:

2 persons, full luggage compartment, or

4 persons without luggage:

approx. 90 miles
/ 150 km.
>With a full load:

4 persons or more, full luggage compart
-
ment:

approx. 30
miles
/ 50 km.
Drive cautiously. Do not exceed a speed of 50
mph
/ 80
km/h. In case of
tire pressure loss you must expect changes
in vehicle handling such as lower track sta
-
bility during braking, longer braking dis
-
tances and changes in self-steering proper
-
ties when close to the handling limit.

For safety reasons, the manufacturer of
your vehicle recommends not having dam
-
aged Run Flat tires repaired. In this case,
consult your MINI dealer.<
Tire change set
In case of a flat tire, the tire change set is not needed, since your vehicle
has Run Flat tires.

When changing a tire, always observe the
safety measures and the procedure for
changing tires starting on page
125
.<
Your vehicle is additionally equipped with a
tire change set.In the MINI COOPER and MINI COOPER Con
-
vertible this is located in the luggage com
-
partment under the floor mat.

In the MINI COOPER
S and MINI COOPER S
Convertible, the tire change set is located in
a separate bag which is attached to the
lashing eyelets on the luggage compart
-
ment floor by means of tie-down straps.
Have new wheels and tires mounted only by a tire specialist. Work that is
improperly carried out could result in con
-
sequential damage and pose safety haz
-
ards. about the correct wheel and tire combina
-
tion for your vehicle.

Have the wheels balanced after each tire or
wheel replacement. The correct wheel and tire combination is
also important for various systems that
would otherwise be impaired, e.g. ABS or
DSC.
The manufacturer of your vehicle rec
-
ommends that you avoid using
retread tires, as this could impair driving
safety. This is due to the possible variations
in casing structures and, in some cases, to
their extreme age, which can lead to a
decrease in their durability.<

103
OVERVIEW REPAIRSOPERATIONCONTROLS DATA INDEX
NEW WHEELS AND TIRESThe correct wheels and tires
The manufacturer of your vehicle

recommends mounting only wheels
and tires that it has specifically tested and
approved for use on your particular model.
Although other wheels and tires may theo
-
retically have the same dimensions, varia
-
tions in factors such as manufacturing tol
-
erances can result in contact between tire
and bodywork, ultimately leading to seri
-
ous accidents. The manufacturer of your
vehicle cannot evaluate non-approved
wheels and tires to determine if they are
suited for use, and therefore cannot ensure
the operating safety of the vehicle if they
are fitted. response, use only tires of a single brand
and tread configuration. In the event of a
flat tire, remount the previous wheel and
tire combination as soon as possible.Recommended tire sizes and brands:For each tire size, certain tire brands have
been tested, classified as road safe and
approved by the manufacturer of your
vehicle. You can find out about these from
a professional tire center, preferably your
MINI Dealer. Observe any local regulations,
e.g. on making a corresponding entry in the
vehicle documents. The factory-approved radial belt tires are
matched to your vehicle and provide opti
-
mum safety and driving comfort when
used properly.Run Flat tires:If your vehicle is equipped with Run Flat
tires, refer to Run Flat tires, please note the
following: when mounting new tires or
replacing summer tires with winter tires, or
vice versa, use only Run Flat tires since no
spare wheel is available in the event of a
flat. The manufacturer of your vehicle will
be glad to advise you.Special characteristics of winter tires The manufacturer of your vehicle recom
-
mends winter tires for driving in adverse
winter road conditions. While all-season
tires with the M+S designation provide bet
-
ter winter traction than summer tires, they
generally do not achieve the full perfor
-
mance of winter tires. Observing speed ratings:
Never exceed the maximum speed for which the winter tires are rated.
Unprofessional attempts by laymen to ser
-
vice tires can lead to damage and acci
-
dents. Have this work performed by skilled
professionals only. The technicans at your
MINI Dealer will be glad to assist you with
the required professional knowledge and
specialized equipment. them against light whenever possible. Pro
-
tect the tires against contact with oil,
grease and fuel. Do not exceed the tire
inflation pressure specified on the tire side
-
wall.

104
SNOW CHAINS
*
Only certain types of snow chains have
been tested by the manufacturer of your
MINI, classified as road-safe and approved.
Contact your MINI Dealer for more details.
The manufacturer of your MINI recom
-
mends that you use only these approved
fine-link snow chains. Their use is only per
-
mitted in pairs on the front wheels on win
-
ter tires of the following types: >175/65 R 15 M+S>175/60 R 16 M+S.When fitting, comply with the manufac
-
turer's instructions. With chains, do not
exceed a speed of 30
mph
/ 50
km/h.
Do not initialize the Flat Tire Monitor after attaching snow chains to the
tires.
When driving with snow chains, it can be
helpful to switch off the ASC or DSC for a
brief period, refer to pages
68, 69
.<

120
ONBOARD TOOL KIT
WIPER BLADES
The picture shows as an example the tire change set with onboard tools for vehicles
with the space-saver spare tire.Depending on the equipment version, your
vehicle is equipped with a special onboard
tool kit stored at the locations described
below:
Tire change set with onboard tools for
space-saver spare tireIn the luggage compartment under the
floor mat.MINI Mobility System with tire change
set and onboard tools In the luggage compartment under the
floor mat.Tire change set and onboard tools for
Run Flat tires >Tire change set:

In the luggage compartment in a sepa
-
rate pouch>Onboard tool kit:

On the left-hand side of the luggage
compartment behind the side trim
panel.
Windshield wiper1. Rotate the wiper arm completely out
from the windshield 2. Set the wiper blade at an angle3. Press the securing spring, arrow4. Unhook the wiper blade towards the
windshield5. Pull the wiper blade past the wiper arm
toward the top6. Insert the new wiper blade7. Press into position until you hear it
engage.

125
OVERVIEW REPAIRSOPERATION CONTROLS DATA INDEX
REPAIRING A FLAT TIRE
SPACE-SAVER SPARE TIRE
*
Safety measures in the event of a flat tire:

Stop the vehicle as far as possible from
passing traffic. Switch on the hazard warn
-
ing flashers.

Turn the steering wheel to the straight-
ahead wheel position and engage the
steering lock. Engage the parking brake and
shift into 1st or reverse gear – selector lever
in P.

All passengers should be outside the vehi
-
cle and well away from your immediate
working area – behind a guardrail, for
instance.

If a portable hazard warning lamp is avail
-
able, set it up on the roadside at an appro
-
priate distance from the rear of the vehicle.
Comply with all safety guidelines and regu
-
lations. -
dures should be followed depending on the
equipment included in your vehicle:>Vehicles with Run Flat tires, refer to
page
101
>Vehicles with a space-saver spare tire,
refer to the following section>Vehicles with MINI Mobility System,
refer to page
129
.
To change a space-saver spare tire, proceed
as follows:>Remove space-saver spare tire, refer to
the section after the next one>Prepare for tire change, refer to page
127
>Jack up the vehicle, refer to page
128
>Mount the space-saver spare tire, refer
to page
128
>Tighten the lug bolts, refer to page
128
>Drive with space-saver spare tire, refer to
page
127
.
Tire change setOn vehicles with a space-saver spare tire,
the tire change set with onboard tools is
stored in the luggage compartment under
the floor mat.1 Chock, folding2 Hubcap remover3 Wheel stud wrench4Jack5 Special wrench for removing the space-
saver spare tire6 Towing eyelet7 Lifting handleThe onboard tool kit includes a pouch with
a plastic bag in which you can place the
damaged wheel.

127
OVERVIEW REPAIRSOPERATION CONTROLS DATA INDEX
SPACE-SAVER SPARE TIRE
*
CHANGING TIRES
9.
Pull out the space-saver spare tire towards the rear underneath the vehi
-
cle
10. Position the space-saver spare tire with
the valve facing upwards11. Unscrew the valve extension from the
valve of the space-saver spare tire12. Unscrew the dust cap from the exten
-
sion and place it on the valve of the
space-saver spare tire.Due to its different dimensions, the damaged wheel cannot be placed in
the recess for the space-saver spare tire.<
Driving with the space-saver spare tireDrive cautiously. Do not exceed a speed of
50 mph
/ 80
km/h.
You must expect changes in vehicle han
-
dling such as lower track stability during
braking, longer braking distances and
changes in self-steering properties when
close to the handling limit. These effects
are more pronounced when driving with
winter tires.
Only one space-saver spare tire may be mounted at one time. Reinstall a
wheel and tire of the original size as soon
as possible. if necessary. Replace the defective tire as
soon as possible and have the new wheel/
tire assembly balanced.<
Additional safety measures in the event of a tire change:

Change the tire only on a level, firm surface
which is not slippery.

The vehicle or the jack could slip sideways
on soft or slippery support surfaces, such as
snow, ice, flagstones, etc..

Do not use a wooden block or similar object
as a support base for the jack, as this would
prevent it from extending to its full support
height and reduce its load-carrying capac
-
ity.

Do not lie under the vehicle or start the
engine when the vehicle is supported by
the jack – risk of fatal injury. Observe the safety precautions regarding flat tires on page
125
.<
1. For vehicles with a space-saver spare
tire:

Place the folding chock behind the front
wheel on the other side of the vehicle;
on downward inclines, place it in front of
this wheel. If the wheel is changed on a
surface with a more severe slope, take
additional precautions to secure the
vehicle from rolling
2. Loosen the lug bolts by a half turn.

129
OVERVIEW REPAIRSOPERATION CONTROLS DATA INDEX
MINI MOBILITY SYSTEM
*
MINI Mobility SystemThe MINI Mobility System is provided to
help you repair a flat tire. With the help of
this system you can apply a liquid sealant
on the inside of the tire, which seals the
damaged area and enables you to continue
to drive. Preparing for tire repair
Before using the MINI Mobility Sys
-
tem read the warning and danger
precautions on the equipment.<
If possible, leave objects in which have
been forced into the tire.Take off the tag regarding speed limits and
stick it onto the steering wheel.Using the MINI Mobility SystemIn order to repair a flat tire with the MINI
Mobility System, proceed as follows:>Pump in liquid sealant, refer to page
130
>Reinflate the tire, refer to page
130
>Distribute liquid sealant, refer to
page
131
>Check tire inflation pressure, refer to
page
131
>Drive on, refer to page
131
.
MINI Mobility System with onboard tools The MINI Mobility System with tire change
set and onboard tools is located in the lug
-
gage compartment under the floor mat:
1Jack2 Wheel stud wrench3 Hubcap remover4 Wrench, screwdriver/Phillips screw
-
driver, towing eyelet5 Compressor, hose with manometer and
plug for cigarette lighter socket6 Package with filling hose, valve remover
and valve core7 Filling canister8 Hex wrench/screwdriver9 Adapter for wheel lug lock

130
MINI MOBILITY SYSTEM
*
Pumping in liquid sealant 1. Shake the filling canister2. Screw the filling hose onto the filling
canister3. Unscrew the dust protection cap from
the valve of the defective tire4. Screw out the valve core with the valve
remover. The valve remover is located in
a package with the filling hose.
Place the valve core and valve remover only on clean surfaces.<
5. Remove the cap from the filling hose6. Push the filling hose onto the tire valve
7. Hold the filling canister with the cap
down and squeeze.

Squeeze the entire contents of the canis
-
ter into the tire
8. Remove filling hose9. Screw valve core into the tire valve with
the valve remover.
In the event of a lost or dirty valve core you will find another valve core
in a package with the filling hose.

Please remember that the liquid canister
must be replaced every four years if the
equipment has not been used.<
Reinflating the tire1. Screw hose
1 with manometer onto the
tire valve
2. Connect plug
3 to the cigarette lighter
socket in the vehicle interior, refer to
page
82
3. Ignition key in position
1:
Turn on compressor
2
4. Inflate the tires to at least
26 psi /
180
kPa, but not to more than 36
psi /
250
kPa.

To check the current air pressure, shut
off the device for a short time.
Do not run the compressor for longer than 6 minutes, otherwise
the device will overheat and possibly be
damaged.<

131
OVERVIEW REPAIRSOPERATION CONTROLS DATA INDEX
MINI MOBILITY SYSTEM
*
If an air pressure of
26 psi
/
180
kPa cannot be reached,
unscrew the hose
1 and drive back and
forth about
33 ft / 10
m so that the liq
-
uid sealant is distributed in the tire.
Afterwards repeat the procedure.

If an air pressure of 26
psi / 180
kPa is
still not reached, the tire is too badly
damaged. Please contact the nearest
MINI Dealer.<
5. Turn off compressor
2
6. Unscrew hose
1 from the tire valve
7. Store the MINI Mobility System back in
the vehicle.
The instructions for using the MINI Mobility System are also given on the
equipment.<
Distributing liquid sealantImmediately drive for approx. 10
minutes,
so that the liquid sealant is uniformly dis
-
tributed.
Do not exceed a speed of 40
mph
/
60 km/h.

If possible do not drive at a speed lower
than 10
mph
/ 20
km/h.<
Checking tire inflation pressure 1. After driving for approx. 10
minutes, pull
over at a suitable location
2. Screw hose with manometer back onto
the tire valve3. Check the tire inflation pressures.
The tire inflation pressure must be at least 18
psi / 130
kPa. If it is not,
do not continue driving.<
If 18
psi / 130
kPa are displayed:
4. Ignition key position 1:

Turn on compressor 2. Correct the tire
inflation pressure to the specified value,
refer to the tire inflation pressure table
on page
98
5. Replace the tire as soon as possible.
The use of the MINI Mobility System may be ineffective with tire damage
larger than approx.
1/6 in / 4 mm. Please
contact the nearest MINI Dealer if the tire
cannot be made drivable with the MINI
Mobility System.<
Driving on
Do not exceed the permitted maxi
-
mum speed of 50
mph
/ 80
km/h;
otherwise an accident could happen.<
Replace the defective tire as soon as possible and have the new wheel/tire
assembly balanced. Have the MINI Mobility
System refilled.<
Tire change setWhen changing a tire, always observe the
safety measures and the procedure for
changing tires starting on page
125
.
In case of a flat tire the tire change set is not needed due to the availabil
-
ity of the MINI Mobility System.<

EVERYTHING FROM A TO Z
148
A ABS Antilock Brake System
70
indicator lamp
17, 18
Accessories, refer to Your
individual vehicle
6
Activated-charcoal filter
80
Adjusting interior
temperature
76, 79
Air circulation, refer to
Recirculated air mode
76, 79
Air conditioning

air conditioning system
76
automatic climate control
79
Air conditioning system
75
Air distribution

air conditioning system
76
automatic climate control
79
Air outlets, refer to
Ventilation
77, 80
Air pressure, refer to Tire
inflation pressure
97
Air volume

air conditioning system
76
automatic climate control
79
Airbags
72
safe seating position
41
warning lamp
18
AKI, refer to Fuel quality
94
All Season traction Control
(ASC)
68
indicator lamps
17, 18
All-season tires, refer to Winter
tires
103

Antenna
114

Antifreeze

coolant
110

washer fluid
108

Antilock Brake System (ABS)
70
indicator lamp
17, 18
Anti-theft system
24
Approved axle load, refer to
Weights
143
, 144

Approved engine oils
109

Approved gross vehicle weight,
refer to Weights
143
, 144

ASC All Season traction
Control
68
indicator lamps
17, 18
Ashtray
81
Assistant systems, refer to

All Season traction Control
(ASC)
68
Dynamic Stability Control
(DSC)
69
AUTO program, refer to
Automatic air distribution
79
Automatic

air distribution
79
air volume
79
cruise control
61
Automatic car washes
113

Automatic climate control
78
Automatic transmission

with Steptronic

indicator lamp
56
interlock
51
selector lever lock
54
shiftlock
54
towing
136

tow-starting
137

Average consumption
67
setting units
67
Average speed
67
setting units
67
Axle loads, refer to
Weights
143
, 144

B Backrests, refer to

Adjusting seats
43
Backup lamp
54
bulb replacement
123

Bar, towing
137

Battery
132

charging
132

disposal
132

indicator lamp
16
jump-starting
134

power failure
132

Battery care
65, 112

Belts, refer to Safety belts
45
Beverage holders
81
Blower

air conditioning system
76
automatic climate control
79
Blower, refer to Air volume
76
Blowers, refer to Draft-free
ventilation
77, 80
Bonnet
105

indicator lamp
17
Bottle holders, refer to
Beverage holders
81
Brake discs

brake system
96
break-in procedures
92
Brake fluid
111

adding
111

level
96
warning lamp
16
Brake lamps, bulb
replacement
123

Brake pads
96
break-in procedures
92
warning lamp
18
Brake system
96
brake fluid
96
brake pads
96
break-in procedures
92
disc brakes
96
warning lamp
17
Brake wear warning

brake pads
96
warning lamp
18