mirror MITSUBISHI 3000GT 1991 Service Manual

EXTERIORCONTENTS
MSIAA- -AERO PARTS
........................................................20
SERVICE ADJUSTMENT PROCEDURES........
10DOOR MIRROR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38Inspection of Active Aero System. . . . . . . . . . . . . . . .10FRONT BUMPER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..__...............11SPECIAL TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..__............_._...4
GARNISHES
AND MOULDINGS . ..__............... 16
REAR BUMPER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14SPECIFICATIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .._...............2General Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Sealants and Adhesives
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3REAR WIPER AND WASHER
. . . . . . . . . . . . . . . . . . . . . . . . . . . .35Service Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3TROUBLESHOOTING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5WINDSHIELD WIPER AND WASHER
. . . . . . . . . . . .24

/
L
,
LJEXTERIOR
- SDecifications-a- - -~------~----ItemsSpecifications
Wiper and washer switch
Rated load A
Wiper switch
LO, HI4
INT0.22 f 0.05
Washer switchMax. 4
Voltage drop (at
12V and the rated load)VWiper switch0.2 or less
Washer switch0.5 or less
Rear wiper and washer switch
Rated load A
Wiper switch
5Washer switch
5Voltage drop V0.1 or less
Intermittent wiper relay

Intermittent interval (min.-max.)sec.
Variable-interval intermittent wiperApprox. 3
- 12
Delay time in washer movingsec.
0.6
Intermittent intervalsec.
8+2Door mirror
Printed heater lines
Working voltage V
IO-15Operating current A3.5 or less
Resistance
s17.7 - 10.2SERVICE SPECIFICATIONSMBlKC-
-ItemsSpecifications
Standard value
Front wiper blade park position
(A)mm (in.)15 ‘-; (.6 +_$ISEALANTS AND ADHESIVES
itemsSpecified adhesive
I
3M ATD Part No. 8609 SUPER FAST URETHANor equivalent
3M ATD Part No. 6382 or equivalent
r--- ~~Side garnish3M ATD Part No. 6382 or equivalent
TSB Revision

EXTERIOR - Troubleshooting
i.l
L
ELECTRIC REMOTE CONTROLLED MIRRORMSlEBBFCIRCUIT DIAGRAM
BEI
LLIfs
9LF?
PWATED
1
@iOA
w&
:ERIGNITIONSWITCH(ACC)-I
d
4
J/B
@ ::::15A
9
C-82
m
$i$iiq
:I1I’II
,IIIIIIII
IttI
1II,I
IIII
IIIt,
---------------------2 2
f
D-42
'-14
7
83296m9
-?;'9:c:a > c3> u,
REMOTEfjI#;"o;LLE'
EFti
tIL-------------q+1~-I~---------------------)L13w
.D-43 ‘1'8--- ---- ------------------ +’'7at2 D-41
/liRmqtI.) El::
:
1
(LH)(RH)
REMOTEiy;;I$)LLED:l:VEHICLES WITH MIRROR HEATERKXS-AC-R13C3-NYX2:VEHICLES WITHOUT MIRROR HEATEFOPERATION
l When the remote controlled mirror switch is
operated while the ignition key is in “ACC” or
“ON” position, current flows through fuse No.@ remote controlled mirror switch, remote
controlled mirror,remote controlled mirror
switch, and ground, causing the mirror to move.TROUBLESHOOTING HINTS
Neither right nor left mirror operates
1) Also cigarette lighter does not operate
l Check multi-purpose fuse No.
0.2) Cigarette lighter operates
l Check remote controlled mirror switch.
TSB Revision

51-38EXTERIOR - Door Mirror
DOOR MIRRORREMOVAL AND INSTALLATION~MSlGAAR
I18FO166
Door mirror removal steps
l *I. Door mirror
2. Harness connector
a*3. Mirror
Electric remote controlled mirror switch removal
4. Instrument panel switch
5. Electric remote controlled mirror switch
Pivnt
NotchesSERVICE POINTS OF REMOVAL
1. REMOVAL OF DOOR MIRROR
Tilt the door mirror backward and forward to remove the
attaching bolts.
3. REMOVAL OF MIRROR
Tilt the mirror upward and fit a screwdriver blade covered
with protective tape in the notch between the mirror and
the pivot plate to pry up the mirror.
Caution
Do not fit the screwdriver blade between the pivot
plate and actuator assembly.
\
LjTSB Revision

cEXTERIOR
- Door Mirror
51-39
witpout heater>18FO167
18FO22(!IINSPECTION
DOOR MIRROR
(1) Check to be sure that the mirror moves as described in the
table when each terminal is connected to the battery.
(2) Check to see that there is continuity between terminals 1
and 5.
RIGHT00
LEFT00
00
NOTE(I)
(2)O-O indicates that each terminal is connected to the battery* indicates door mirror terminal on vehicles without heater.
ELECTRIC REMOTE CONTROL MIRROR SWITCH
Operate switches and check for continuity between terminals.
TSB Revision