warning lights MITSUBISHI 3000GT 1991 Service Manual

SERVICE BRAKES -Anti-lock Braking System Troubleshooting
35-11
Adapter
iarness%f&(MB9913771(Mi3991341)\12FOO57
CHECK USING SELF DIAGNOSIS FUNCTION
(1) With the ignition switch OFF, connect the MUT through the
adapter harness
(MB9913771, turn the ignition ON and
select the ABS system. (The ABS warning light lights up, it
goes into the MUT mode. In the MUT mode, ABS does
not function.)
If it does not go into the MUT mode, check the ECU power
circuit and the harness between the ECU and diagnosis
check terminals.
(2) Read the diagnosis output codes from the ECU memory.
(3) Clear the diagnosis codes once from memory. (Refer to
P.35-12.)If the memory cannot be cleared, the ECU is currently
detecting the trouble and the ABS ECU is in fail safe. If it
can be cleared, the trouble is either temporary or appears
only when driving.
(4) When the trouble codes cannot be cleared, or when the
ABS ECU goes into fail safe during another test drive and
trouble codes are output, check according to trouble code
check charts (E-l-E-6).
DIAGNOSIS CODE CHART
Diagnosis codeCheckReferenceDiagnosis codeCheck
Referencechart namepagechart namepawNo. MUT display lettersor remedyNo. MUT display lettersor remedy
L11FR SNSR. OPEN41FR SOL. VALVE
12FL SNSR. OPEN42FL SOL. VALVEE-4P.35-23E-lP.35-2013RR SNSR. OPEN43REAR SOL. V.
14RL SNSR. OPEN51VALVE RELAYE-5P.35-24
15VEH. SPD. SNSR.E-2P.35-20 52MOTOR RELAYE-6P.35-25
22STOP LAMP SWE-3P.35-2055 CONT. UNITECU-
replacementI
TSB Revision

.SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-13 'A ABS warning light does not light at all.
iJ[Explanation][Hint]
When it does not light up at all, there is a strongIf other warning lights do not light up either, fuse is
possibility that there is trouble with ABS warningprobably blown.
light or with power to the light.
id
r
f%ER RELAY
110
* ::h=g
6
::5
d
.-2=
?Et0
~
2____--..-
?EI
5fir 4
I
4 -
IGNITIONSWITCH(IG2)m!--
mj:
JSIBLE LINK0tiB
2
L__---------___
0
Lp1%
%2
j:(L-R)dg
6-k
&h+&"..L"Ei SOLENOID1:
G-R
G-R
^ -tl- - D
HH H?bb
IN:IGl)-
59
1
ki@iNATION
iB
ABS-ECU
Kxss-AK-RSGOIA
1 TSB RevisionI

SERVICE BRAKES -Anti-lock Braking System Troubleshooting
MUT
I/(MB991 341)
\03A0211
DIAGNOSIS CODE CHART
I I21G SNSR.IE-3
[ 22 1 STOP LAMPSW 1E-4
CHECK USING SELF DIAGNOSIS FUNCTION
(1) With the ignition switch OFF, connect the MUT through the
adapter harness (MB991377). turn the ignition ON and
select the ABS system. (The ABS warning light lights up, it
goes into the MUT mode. In the MUT mode, ABS does
not function.)
If it does not go into the MUT mode, check the ECU power
circuit and the harness between the ECU and diagnosis
check terminals.
(2) Read the diagnosis output codes from the ECU memory.
(3) Clear the diagnosis codes once from memory. (Refer to
P.35-30.)If the memory cannot be cleared, the ECU is currently
detecting the trouble and the ABS ECU is in fail safe. If it
can be cleared, the trouble is either temporary or appears
only when driving.
(4) When the trouble codes cannot be cleared, or when the
ABS ECU goes into fail safe during another test drive and
trouble codes are output, check according to trouble code
check charts (E-l-E-7).
Reference
we -1 ;+EiT;
I I41FR SOL. VALVEI
P.35-381 ;; / ;;tS;L;;;E/ E-5
I I51VALVE RELAY
P.35-38 1 52 1 MOTOR RELAY)E-7
si 55 / ‘ONT. UNlT/ replaEcCeUment
Reference
iwe
P.35-42
P.35-43
P.35-44
-
1 TSB RtivisionI

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-31
L’A ABS warning light does not light at all.
[Explanation][Hint]
When it does not light up at all, there is a strongIf other warning lights do not light up either, fuse is
possibility that there is trouble with ABS warningprobably blown.
light or with power to the light.
FUSIBLE LINEI
L--L5--
i
IGNITIONSWITCH(IG2)IGNITIONSWITCH(IG1)
(L-R)-' .3
G-RI
7
!
m59COMBINATION
iMETER
1:I1o‘r_- ----- ‘2 -- ‘Ti----‘%--‘79 -_----- -7 -- “j-+3 -----1
=p!Rq3;
g:W
25
b
ABS-ECU
n=
1 TSB Revision

35-58SERVICE BRAKES - Service Adjustment Procedures
POINTS IN WAVEFORM MEASUREMENT
Symptom
Too small or zero waveform
amplitudeProbable causes
Faulty wheel speed sensorRemedy
Replace sensor
Incorrect pole piece-to-rotor clearance
Adjust clearance
Waveform amplitude fluctuates
excessively (this is no problem ifAxle hub eccentric or with large runout
Replace hub
the minimum amplitude is
100 mV
or more)
Noisy or disturbed waveformOpen circuit in sensor
Open circuit in harness
Incorrectly mounted wheel speed sensor
Rotor with missing or damaged teethReplace sensor
Correct harness
Mount correctly
Replace rotor
NOTEThe wheel speed sensor cable moves following motion of the front or rear suspension. Therefore, it is likely that it has an
open circuit only when driving on rough roads and it functions normally on ordinary roads. It is, therefore, recommended
to observe sensor output voltage waveform also under special conditions, such as rough road driving,
(ME!991 377)12FOO5i
INSPECTION OF HYDRAULIC UNITINSPECTION BY FEEL
(I) Jack up the vehicle and support the vehicle with rigid racks
placed at the specified jack-up points.
(2) Release the parking brake and determine the drag force
(drag torque) of each wheel by feel.
LJ(3) Set the MUT through the adapter harness (MB991377) as
illustrated.
(4) After confirming that the shift lever or selector lever is in
the neutral position, start the engine.
The ABS warning light lights up, it goes into the MUT mode.
In the MUT mode, ABS does not function.
(5) Operate the MUT to force the actuator to operate (item No.
04, 05, 06).
(6) Turning the wheel manually, check the change of the
braking force when the brake pedal is depressed.
The change should be as shown in the following illustration.
NOTEWhile the ABS is in the fail safe mode, the MUT actuator
test cannot be made.
TSB Revision

35-60SERVICE BRAKES - Service Adjustment Procedures
INSPECTION BY USING BRAKE FORCE TESTER
NOTE
(1) The brake force tester roller and tire must be dry during the
test.
(2) When testing the front brakes, apply the parking brake and
when testing the rear brakes, apply chocks to the front
wheels to lock them.
(I) Place the front or rear wheels on the brake force tester
roller.(2) Set the MUT through the adapter harness
(MB9913771 as
illustrated.
(3) After confirming that the shift lever or selector lever is in
the neutral position, start the engine.
(The ABS warning light lights up, it goes into the
-MUTmode. In the MUT mode, ABS does not function.)
(4) Operate the brake force tester roller.
(5) Depress the brake pedal until the brake force tester
indicates the following value and keep the brake force at
this level during the test.
Front wheels: 1,000 N (220
Ibs.)Rear wheels: 650 N (143
Ibs.)(6) Allow the brake tester indication to stabilize before operat-
ing the MUT to perform actuator test (Item No. 01,
02, 03).
Then, read change of tester indication.
Referring to the following “Judgement in Inspection by
Using Brake Force Tester” table, judge and take corrective
action if necessary.
NOTEWhile the ABS is in the fail safe mode, the MUT actuator
test cannot be made.
1 TSB Revision