brake MITSUBISHI CARISMA 2000 1.G User Guide

STARTING AND DRIVING
5–11
CAUTION
(1) Do not remove the ignition key
from the ignition switch while
driving. The steering wheel will
lock, causing loss of control.
(2) If the engine is stopped while
driving, the brake servomechan-
ism will cease to function and
braking efficiency will deterio-
rate. Also, the power steering
system will not function and it will
require greater manual effort to
operate the steering.
(3) Do not leave the key in the “ON”
position for a long time when the
engine is not running, doing so
will cause the battery to be dis-
charged.
(4) Do not turn the key to the
“START” position when the en-
gine is running, doing so could
damage the starter motor.
I01B015a
How to lock and unlock the steer-
ing wheel
EI01B-Kb
To lockRemove the key at the “LOCK” position.
Turn the steering wheel until it is locked.
To unlockTurn the key to the “ACC” position while
moving the steering wheel slightly.
CAUTION
Remove the key when leaving the ve-
hicle.
NOTEIf the front wheels are turned, the anti-theft
lock may sometimes make it difficult to turn
the key from “LOCK” to “ACC”. Firmly turn
the steering wheel to the left or to the right as
you turn the key.

STARTING AND DRIVING
5–13
I27A036a
Starting the engine
(Petrol-powered vehicles)
This vehicle is equipped with an electroni-
cally controlled fuel injection system which
is automatically controlled. When starting
the engine, do not depress the accelerator
pedal.
Normal conditions
The starting procedure is as follows :
1. Insert the ignition key and fasten the
seat belt.
2. Apply the parking brake.
3. Depress and hold the brake pedal.
4. Place the gearshift lever (manual
transmission) in the “N” (Neutral) or
the selector lever (automatic trans-
mission) in the “P” (PARK) position.
5. Fully depress the clutch pedal (man-
ual transmission).
6. After turning the ignition key to the
“ON” position, make certain that all
warning lamps are functioning proper-
ly before starting the engine.
7. Turn the ignition key to the “START”
position without depressing the accel-
erator pedal, and release it when the
engine starts.
NOTE
A ticking noise may be heard after starting
the engine. This is not an abnormal condi-
tion. The noise will disappear after a short
time of engine running.
If the ticking noise continues after the engine
is warmed up, have your vehicle checked at
an authorized MITSUBISHI dealer.
Flooded engine
If the engine has become flooded during
starting, first operate the starter for 5 to 6 sec-
onds while fully depressing the accelerator
pedal, then start the engine without depres-
sing the accelerator pedal.
At extreme cold ambient
temperature
If the engine won’t start, depress the accel-
erator pedal about halfway while cranking
the engine. Once the engine starts, re-
lease the accelerator pedal.
CAUTION
When starting the engine, make sure
that you press on the brake pedal. At
extreme cold ambient temperature,
move your foot to the brake pedal im-
mediately after the engine has
started.

STARTING AND DRIVING
5–14
I27A075a
Starting the engine
(Diesel-powered vehicles)
1. Insert the ignition key and fasten the
seat belt.
2. Apply the parking brake.
3. Depress and hold the brake pedal.
4. Place the gearshift lever in the “N”
(Neutral) position.
5. Fully depress the clutch pedal.
6. Turn the ignition key to the “ON” posi-
tion. The diesel preheat indication
lamp will first illuminate in amber, and
then after a short time go out, indicat-
ing that preheating is completed.
7. Turn the ignition key to the “START”
position without depressing the accel-
erator pedal, and release it when the
engine starts.NOTE
(1) If the engine is cold, the diesel preheat
indication lamp is on for a longer time.
(2) When the engine has not been started
within about 5 seconds after the diesel
preheat indication lamp will go out, re-
turn the ignition key to the “LOCK” posi-
tion. Then, turn the key to the “ON” posi-
tion to preheat the engine again.
(3) When the engine is warm, the diesel
preheat indication lamp does not come
on, even if the ignition key is placed in
the “ON” position.
Start the engine by turning the ignition
key right to the “START” position.
Type 1
I29A014a
Manual transmissionEI29A–Jd
The shift pattern is shown on the gearshift
lever knob. Be sure to always fully depress
the clutch pedal before attempting to shift the
lever.
For smooth gearchanging

Depress the clutch pedal completely.

1st and 2nd gear: first move the gear
lever fully left and then forward or back
into 1st and 2nd gear.

3rd and 4th gear: move the gear lever
forward or back from neutral (N).

5th gear: first move the gear lever right
and then into 5th gear.

STARTING AND DRIVING
5–17
NOTE
During running–in period or immediately
after reconnection of the battery cable, there
may be a case where gearshifts are not
made smoothly. This does not indicate a
faulty transmission.
Gearshifts will become smooth after the
transmission has been shifted several times
by the electronic control system.
I04A235a
Selector lever operation
Except for vehicles with Sports modeThe transmission has 4 forward gears and 1
reverse gear.
The individual gears are selected automati-
cally, depending on the position of the gear
selector lever, the speed of the vehicle and
the position of the accelerator pedal.
The selector lever has 7 positions, and is
equipped with a lock button (A) to avoid inad-
vertent selection of the wrong gear.
Button must be pushed and brake
pedal must be depressed to move
the lever
Button must be pushed to move the
lever.
Button need not be pushed to move
the lever.
I04B008a
Vehicles with Sports modeThe transmission has 4 forward gears and 1
reverse gear.
The individual gears are selected automati-
cally, depending on the position of the gear
selector lever, the speed of the vehicle and
the position of the accelerator pedal.
The selector lever has 2 gates; the main gate
(1) and the manual gate (2).
NOTE
For information on manual gate operation,
please refer to “Sports mode (Vehicles with
Sports mode)” on page 5–22.

STARTING AND DRIVING
5–18
I04A187a
In the main gate, selector lever has 4 posi-
tions, and is equipped with a lock button (A)
to avoid inadvertent selection of the wrong
gear.
I04A209a
Button must be pushed while the
brake pedal is depressed to move
the lever.
Button must be pushed to move the
lever.
Button need not be pushed to move
the lever.
WARNING
(1) If the button is always depressed
to operate the selector lever, the
lever may be accidentally shifted
into the “P”, “R”, “2”, or “L” posi-
tion. Be sure not to depress the
button (A) when performing the
operations indicated by
 in the
illustration.
(2) Always depress the brake pedal
when shifting the selector lever
into a gear from the “P” (PARK) or
“N” (NEUTRAL) position.
When beginning to drive, do not
shift the selector lever form the
“P” (PARK) or “N” (NEUTRAL)
position while depressing the ac-
celerator pedal, doing so is dan-
gerous because the vehicle will
“jump” forward or backward.
NOTE
If the brake pedal is not depressed and held,
the shift-lock device activates to prevent the
selector lever from being moved from the “P”
(PARK) position to another position.

STARTING AND DRIVING
5–20
CAUTION
[The “N” indicator lamp flashes slow-
ly (once per second)]
The automatic transmission safety
device may be operating due to a mal-
function.
Have your vehicle inspected by an
authorized MITSUBISHI dealer as
soon as possible.
Selector positionsEI04BALb
P - PARKThis position locks the transmission to pre-
vent the vehicle from moving. The engine
can be started in this position.
R - REVERSEMove the lever to this position only after the
vehicle has come to a complete stop.
CAUTION
Never shift into the “P” (PARK) or “R”
(REVERSE) position while the vehicle
is in motion. If the lever is shifted into
the “P” or “R” position while the ve-
hicle is in motion, the transmission
may be damaged.
N - NEUTRALAt this position, the transmission is disen-
gaged. It is the same as the neutral position
on a manual transmission, and should be
used when the vehicle is stationary for an ex-
tended length of time during driving, such as
in a traffic jam.
WARNING
(1) Never move the selector lever to
the “N” position while driving.
A serious accident could occur
since you could accidentally
move the lever into the “P” or “R”
position and engine braking
would be lost.
(2) On a slope gradient, the engine
should be started in the “P”
(PARK) position, not in the “N”
(NEUTRAL) position.
(3) Always keep your right foot on
the brake pedal when the vehicle
is in “N” (NEUTRAL), or when
shifting into or out of “N” (NEU-
TRAL), to minimize the risk of
loss of control.
D - DRIVEThis position is for normal driving.
The transmission automatically selects a
suitable gear for your speed and acceler-
ation.
Engine braking is automatically applied
when necessary, depending on road condi-
tions.
Please refer to “Uphill/downhill driving” on
page 5–24.

STARTING AND DRIVING
5–23
I04S037a
Sports mode indicator lampsIn sports mode, the currently selected gear
is indicated by green lamp on the instrument
panel.
NOTE
When sports mode is selected, the “D” indi-
cator lamp goes off.
Operation of the automatic
transmission INVECS-II
EI04DLH
CAUTION
(1) Before selecting a gear with the
engine running and the vehicle
stationary, fully depress the
brake pedal to prevent the vehicle
from creeping.
The vehicle will begin to move as
soon as the gear is engaged, es-
pecially when the engine speed is
high, at fast idle or with the air
conditioning operating, the
brakes should only be released
when you are ready to drive away.
(2) Depress the brake pedal with the
right foot at all times.
Using the left foot could cause
driver movement delay in case of
an emergency.
(3) To prevent sudden acceleration,
never race the engine when shift-
ing from the “P” (PARK) or “N”
(NEUTRAL).
CAUTION
(4) Operating the accelerator pedal
while the other foot is resting on
the brake pedal will affect braking
efficiency and may cause pre-
maturewear of brake pads.
Do not race the engine with brake
pedal pressed.
This can damage the trans-
mission.

STARTING AND DRIVING
5–24
Possible driving speed
(Except for vehicles with Sports
mode)
EI04IMLf
In order to avoid damaging the engine due
to excessively high rpm, do not exceed the
possible driving speed when the selector
lever is set to the “3” (THIRD) position, the “2”
(SECOND) position or the “L” (LOW) posi-
tion.
km/hDrive range1600
“L”
(LOW)45
“2”
(SECOND)100
“3”
(THIRD)155
Passing accelerationEI04F-O
For quick acceleration when passing,
depressing the accelerator pedal all the way
to the floor will cause the transmission to
automatically shift from 4th gear to 3rd gear,
from 3rd gear to 2nd gear or from 2nd gear
to 1st gear, in accordance with the driving
speed, without having to move the selector
lever from the “D” (DRIVE), “3” (THIRD) or “2”
(SECOND) positions.
NOTE
In sports mode, downshifts do not take place
when the accelerator is depressed all the
way to the floor.
Uphill/downhill drivingEI04O-Ia
DRIVING UPHILL
The transmission may not upshift to a higher
gear if the computer determines the current
speed cannot be maintained once a higher
gear is engaged.
For smoother vehicle performance, if you re-
lease the throttle while climbing a steep
grade, the transmission may not upshift. This
is normal, as the computer is temporarily
preventing shifting. After reaching the top of
the hill, normal gear shift function will re-
sume.
DRIVING DOWNHILL
When travelling down steep grades, the
computer may automatically select a lower
gear. This function assists engine braking ef-
forts, reducing the need for using the brakes.

STARTING AND DRIVING
5–25
WaitingEI04G-Ee
For short waiting periods, such as at traffic
lights, the vehicle can be left in gear and held
stationary with the service brake.
For longer waiting periods with the engine
running, the selector lever should be placed
in the “N” (NEUTRAL) position.
CAUTION
(1)Never hold the vehicle stationary
while in gear on a hill with the accel-
erator, always apply the parking
brake and/or service brake.
(2)Unexpected acceleration may occur
if the selector lever is in a position
other than “P” (PARK) or “N” (NEU-
TRAL).
Prior to moving off after having
stopped the vehicle, make sure that
the selector lever is in “D” (DRIVE)
or “Sports mode” position.
ParkingEI04H-Be
To park the vehicle, first bring it to a complete
stop, fully engage the parking brake and
then move the selector lever to the “P”
(PARK) position.
If you are going to leave the vehicle unat-
tended, always switch off the engine and re-
move the ignition key.
NOTE
On a slope, be sure to apply the parking
brake before moving the selector lever to the
“P” (PARK) position. If you move the selector
lever to the “P” (PARK) position without first
applying the parking brake, a stronger than
normal resistance force may be encoun-
tered. In this situation, move the selector
lever strongly when you next wish to drive.
I27A052a
Parking brakeEI07A-Jn
To park the vehicle, first bring it to a complete
stop, fully engage the parking brake and
then move the gear shift lever to 1st (on an
uphill) or Reverse (on a downhill) position, for
vehicles with a manual transmission or set
the selector lever to “P” (PARK) position on
automatic transmission vehicles.
To apply
1-Pull the lever up without pushing the
button at the end of the hand grip.

STARTING AND DRIVING
5–26
I07A045a
To release
1-Pull the lever up slightly.
2-Push the button at the end of the hand
grip.
3-Push the lever downward.
NOTETo prevent the parking brake from being re-
leased unintentionally, the lever must be
pulled upward slightly before it can be
pushed downward. Simply pressing the but-
ton does not enable the lever to be pushed
downward.
When parking on a hill, apply the parking
brake and turn the front wheels towards the
kerb on a downhill grade, away from the kerb
on an uphill grade.
CAUTION
Before driving, be sure that the park-
ing brake is fully released and the
brake warning lamp is off.
If a vehicle is driven without releasing
the parking brake, the brake will be
overheated, resulting in ineffective
braking and possible brake failure.
ParkingEI22A-Al
Parking on a slope
Fully engage the parking brake, and then
move the gearshift lever to 1st (on an uphill)
or reverse (on a downhill) position on manual
transmission vehicle. On automatic trans-
mission vehicle, move the selector lever to
“P” position. When parking on a hill, apply
chocks to wheels for greater safety.
Parking with the engine running
Do not keep the engine running in a closed
or poorly ventilated place. Carbon monoxide
gas is odorless and extremely poisonous
and dangerous.
Where you park
Do not park in a place where there are in-
flammable objects such as dry grass,
leaves, etc... because the exhaust system
with catalyst produces very high tempera-
tures. This may cause a fire.
When leaving the vehicle
Always remove the key from the ignition
switch and lock all doors when leaving the
vehicle unattended.
Always try to park your vehicle in a well lit
area.