warning MITSUBISHI COLT 2008 (in English) Manual PDF

4-32 Starting and driving
4
NOTE●The allshift indicator display shows recommended gear-
shift points for fuel-efficient driving. It shows a “ ”
when an upshift is recommended, and it shows a “ ”
when a downshift is recommended.
Passing acceleration
•Automatic mode: Depress the acceleration pedal to the floor.
•Manual mode: Use the allshift lever to shift to an appropriate gear before depressing the accelerator pedal to
accelerate. Driving downhill
When driving downhill, shift down to an appropriate gear in
order to use engine braking.
On long downward slopes, repeated use of the brake pedal can
cause the brake system to overh
eat, resulting in reduced brak-
ing performance. Be sure to us e engine braking as well as the
brake system.
orWARNING!
● Hard engine brak ing can cause the tyres to slip on
the road surface, possibly leading to a serious acci-
dent.

Starting and driving4-35
4
Braking
E00607000947
All parts of the brake system ar
e critical for safety. We recom-
mend that you have the vehicl e checked at regular intervals
according to the service booklet.
Brake system
The service brake is divided into two brake circuits so that if
one brake circuit fails, the othe r one is available to stop the
vehicle. In this situation, ev en if the brake pedal moves down
to the very end of its possible stroke, keep it pressed down
hard; stop driving as soon as possible and have the brake sys-
tem repaired.
Power brakes
Your vehicle is equipped with power brakes for more braking
force with less brake pedal effort.
Your brakes are designed to oper ate at full capacity, even if the
power assist is not being used.
If the power assist is not being used, the effort needed to press
the brake pedal is greater.
If you should loose the power assist for some reason, the
brakes will still work. If the power brake unit or either
of the two brake hydraulic sys-
tems stops working properly, the rest of the brake system will
still work, but the vehicle will not slow down as quickly.
You will know this has happened if you find you need to press
the brake down further or harder when slowing down or stop-
ping, or if the brake warning lamp comes on.
Wa r n i n g l a m p
The brake warning lamp will illuminate to indicate a fault in
the braking system. Read “Brake warning lamp” on page 3-9.
When brakes are wet
Check the brake system while dr iving at a low speed immedi-
ately after starting, especially wh en the brakes are wet, to con-
firm they work normally.
A film of water can be formed on the brake discs or brake
drums and prevent normal braki ng after driving in heavy rain
or through large puddles, or after the vehicle has been washed.
If this occurs, dry the brakes out by driving slowly while
lightly depressing the brake pedal.
CAUTION!
● Avoid driving habits that cause heavy braking and
never “ride” the brakes by resting your foot on the
brake pedal while driving.
This causes brake overheating and fade.WARNING!
● Never coast downhill with the engine OFF. Keep the
engine running whenever your vehicle is in motion.
If you turn off the engine while driving, the power
brake booster will stop working and your brakes
will not work as well.
● If the power assist is lost or if either brake hydraulic
system stops working properly, have your vehicle
checked immediately.

4-36 Starting and driving
4
When driving downhill
It is important to take advantage of engine braking by shifting
to a lower shift position while driving on steep downhill roads
in order to prevent the brakes from overheating.
Brake pads and linings
●With new brake pads or linings, avoid where possible sud-
den full application of the brakes for the first 200 km (120
miles) of driving.
● The disc brakes are fitted with a warning device which
emits a shrieking metallic sound while braking if the
brake pads have reached their limit.
If you hear this sound, have the brake pads replaced.
Anti-lock brake system (ABS)
E00607100791
Environmental conditions can ha ve an effect on braking. Dur-
ing sudden braking when there is snow, ice, oil, water etc. on
the road surface, a skid may occur. In this situation, steering
control and braking effectivenes s is reduced and the stopping
distance is increased. The vehicl e may also go into an uncon-
trolled spin.
The ABS helps prevent the wheel s from locking during brak-
ing, thus maintaining directional stability, ensuring controlla-
bility and providing optimum braking force.
Driving hints
● When using the anti-lock brak e system (sudden braking),
steering is slightly different from normal driving condi-
tions. Use the steering wheel carefully.
● Always maintain the same di stance from the vehicle in
front of you as you would for a vehicle not equipped with
ABS.
Compared with vehicles not fitted with ABS, your vehicle
may require a longer stopping distance in the following
cases:
• Driving on gravel or snow-covered roads.
• Driving with tyre chains installed.
• Driving on roads where the road surface is pitted or has
other differences in surface height.
• Driving on bumpy roads or other poor driving surfaces.
WARNING!
●Do not leave any objects ne ar the brake pedal or let
a floor mat slide under it; doing so could prevent the
full pedal stroke that woul d be necessary in an emer-
gency. Make sure that the pedal can be operated
freely at all times. Make sure the floor mat is
securely held in place.
WARNING!
● Driving with worn brake pads will make it harder to
stop, and can cause an accident.

4-38 Starting and driving
4
ABS warning lampE00607200718
The ABS warning lamp comes on and a buzzer sounds in the
event of a malfunction in the anti-lock brake system. It will
also come on as a self-check for a few seconds when the igni-
tion switch is turned to the “ON” position. The lamp goes out
after a few seconds. Always make sure that the lamp goes out
before starting to drive.
If the warning lamp illuminates while drivingE00607300881
If only the ABS warning lamp illuminates
● Avoid hard braking and high-speed driving. Stop the vehi-
cle in a safe place.
Restart the engine and check to see if the lamp goes out
after a few minutes of driving; if it remains off during
driving, there is no problem.
However, if the lamp does not go out, or if it lights up
again when the vehicle is dr iven, we recommend that you
consult a MITSUBISHI MOTORS Authorized Service
Point.
● The ABS warning lamp can illuminate if there is insuffi-
cient battery voltage when the engine is started. In this
case, it does not indicate an ABS fault.
Charge the battery by allowing the engine to idle for a
while.
If the battery has been charged but the ABS warning lamp
continues to illuminate or illuminates intermittently, we
recommend that you cons ult a MITSUBISHI MOTORS
Authorized Service Point.
If the ABS warning lamp and brake warning lamp
illuminate at the same time
● The brake force distribution function may not work, so
hard braking could make the vehicle unstable.
Avoid hard braking and high-speed driving. Stop the vehi-
cle in a safe place and we recommend that you consult a
MITSUBISHI MOTORS Authorized Service Point.CAUTION!
●If the warning lamp stays on or does not illuminate
when you start the vehicle, it indicates that the ABS
is not functioning and that only the standard brake
system is in operation. (I n this condition the stand-
ard hydraulic brake system will still function.) We
recommend that you consult a MITSUBISHI
MOTORS Authorized Service Point.

Starting and driving4-41
4
Electric power steering warning lampE00612400011
The electric power steering wa rning lamp comes on and a
buzzer sounds in the event of a control abnormality in the elec-
tric power steering system.
When the system is normal, th e electric power steering warn-
ing lamp comes on when the ignition switch is turned to the
“ON” position and goes off after a few seconds.
If the warning lamp illuminates while drivingE00613600049
1. Park your vehicle in a safe place and stop the engine.
2. Turn the ignition switch to the “ON” position. If the elec- tric power steering warning lamp comes on then goes off
after a few seconds, there is no abnormality. However, if
the lamp does not go off, or if it comes on again when the
vehicle is driven, we recommend you to have the power
steering inspected by a MI TSUBISHI MOTORS Author-
ized Service Point.
CAUTION!
● If the electric power steering warning lamp comes
on while the vehicle is m oving, the steering action
may become heavy.

4-42 Starting and driving
4Traction control system (TCL)/Active
stability control system (ASC)
*
E00611700033
The traction control system (TCL )/active stability control sys-
tem (ASC) takes overall control of the anti-lock brake system,
traction control system and activ e stability control system to
help maintain the vehicle’s control and traction. Please read
this section in conjunction with the page on the anti-lock brake
system, traction control system and active stability control sys-
tem.
Anti-lock brake system (ABS) → P. 4-36
Traction control system (TCL) → P. 4-43
Active stability control system (ASC) → P. 4 - 4 3
NOTE● Immediately after the vehicle starts moving after engine
start up, a whining sound of a motor will be heard from
the engine compartment. If the brake pedal is depressed at
that moment, a brake pedal pulsating is felt.
This whining sound and pulsation are due to the self-diag-
nosis operation of the traction control system (TCL)/
active stability control system (ASC) and does not indi-
cate a malfunction.
● Some vibration will be felt in the vehicle body and a
whining sound of a motor will be heard from the engine
compartment when the tract ion control system (TCL)/
active stability control system (ASC) functions. This is a
normal result of the traction control system (TCL)/active
stability control system (ASC) operation, and does not
indicate a malfunction.
● The traction control system (T CL)/active stability control
system (ASC) does not operate while the ABS warning
lamp is illuminated.
CAUTION!
● Do not over-rely on the traction control system
(TCL)/active stability control system (ASC). Even
when the traction control system (TCL)/active sta-
bility control system (ASC ) is operating, there are
limits to the system and its ability to maintain con-
trol and traction. Reckless driving may lead to acci-
dents. Always drive carefully, taking account of the
road conditions.
● Be sure to use the same specified type and size of
tyre on all 4 wheels. Otherw ise, there is a possibility
that the traction control system (TCL)/active stabil-
ity control system (ASC) will not work properly.

5-58 For pleasant driving
5
●Do not put additional labels (A) or stickers (B) on com-
pact discs. Do not use any compact disc on which a label
or sticker has started to peel off or any compact disc that
has stickiness or other contamination left by a peeled-off
label or sticker. If you use such a compact disc, the CD
player may stop working properly and you may not be
able to eject the compact disc.Notes on CD-Rs/RWsE00725100026
●You may have trouble playing back some CD-R/RW discs
recorded on CD recorders (C D-R/RW drives), either due
to their recording characteris tics or dirt, fingerprints,
scratches, etc. on the disc surface.
● CD-R/RW discs are less resistant to high temperatures and
high humidity than ordinary music CDs. Leaving them
inside a vehicle for extended periods may damage them
and make playback impossible.
● The unit may not successfully play back a CD-R/RW that
was made by the combination of writing software, a CD
recorder (CD-R/RW drive) an d a disc if they are incom-
patible with one another.
● This player cannot play the CD-R/RW discs if the session
is not closed.
● This player cannot play CD-R/RW discs which contain
other than CD-DA or MP3 data (Video CD, etc.).
● Be sure to observe the handling instructions for the CD-
R/RW disc.
WARNING!
●Operating the CD player in a manner other than
specifically instructed herein may result in hazard-
ous radiation exposure. Do not remove the cover
and attempt to repair the CD player by yourself.
There are no user serviceabl e parts inside. In case of
malfunction, we recommend you to have it checked.

5-72 For pleasant driving
5Coat hooks
*
E00725600148
There are two hooks on the rear pillar for use in hanging
clothes.
Luggage hooks (5-door models)*
E00715700407
There are hooks on the floor.
Use the hooks on the floor for securing the luggage.
WARNING!
●
Do not put a hanger or any heavy or pointed object
on the coat hook. If the cu rtain air bag is activated,
such items could be propelled away with great force
and could prevent the curtai n air bag from inflating
correctly. Hang clothes di rectly on the coat hook
(without using a hanger). Make sure there are no
heavy or sharp objects in the pockets of clothes
hanging on the coat hook.
CAUTION!
● Do not pile up the luggage beyond the seatback
height.
Secure the luggage firmly.
Otherwise, serious accident s could result due to hin-
dered rearward view or fl ying objects during sud-
den braking.

6-2 For emergencies
6If the vehicle breaks down
E00800100185
If the vehicle breaks down on th
e road, move it to the shoulder
and use the hazard warning flashers.
If the engine stops/fails
Vehicle operation and control are affected if the engine stops.
Before moving the vehicle to a safe area be aware of the fol-
lowing: ● The brake booster becomes inoperative and the pedal
effort will increase. Press down the brake pedal harder
than usual.
● Turn the wheel with more effort than usual.
Emergency starting
E00800501229
If the engine cannot be started because the battery is weak or
dead, the battery from another vehicle can be used with jump
leads to start the engine.
1. Get the vehicles close enoug h so that the jump leads can
reach, but be sure the vehicles aren’t touching each other.
If they are, it could cause an unwanted ground connection.
The vehicle will not start in this case, and the bad ground-
ing could damage the electrical systems.
WARNING!
● To start the engine using jump leads connected to
another vehicle, perfor m the correct procedures
according to the instruct ion manual. Incorrect pro-
cedures could result in a fire or explosion or damage
to the vehicles.
CAUTION!
● Check the other vehicle. It must have a 12-volt bat-
tery.
If the other system isn’t 12-volt, shorting can dam-
age both vehicles.

For emergencies6-3
6
2. You could be injured if the vehicles move. Set the parkingbrake firmly on each vehicle. Put an automatic transmis-
sion in “P” (PARK) or a manua l transmission and an auto-
mated manual transmission in “N” (Neutral). With an
automated manual transmission vehicle, confirm that “N”
is shown by the allshift indicator display. Turn off the
ignition switch.
NOTE● Turn off all lamps, the heater and other electrical loads.
This will avoid sparks and help save both batteries.
3. Make sure battery electrolyte is at the proper level. Refer to “Battery” on page 8-15. 4. Connect one end of one jump lead to the positive (+) ter-
minal of the discharged battery (A), and the other end to
the positive (+) terminal of the booster battery (B).
Petrol-powered vehicles


WARNING!
● Turn off the ignition on both vehicles beforehand.
Take care to ensure that the cables or your clothes
cannot be caught by the fan or drive belt. Personal
injury could result.
WARNING!
● If electrolyte fluid is not vi sible, or appears to be fro-
zen, Do Not Attempt Jump Starting!
A battery might rupture or explode if the tempera-
ture is below freezing point or if it is not filled to the
proper level.
Except for vehicles with turbocharger