sensor MITSUBISHI ECLIPSE 1991 Owner's Guide

BRAKES - Wheel Speed Sensor 5-81;
7-10 ft.lbs.
IPost-installation Operation@Installation of the Snlash ShieldI
1 (Refer to GROUP 23-Fender.)17-11 Nm
14A0582Front speed sensor removal steps
4*1. Front toothed rotor
2. Clip
3. Front speed sensor connection
4I) WI 4. Front speed sensor
l 5. Front speed sensor bracket
Rear speed sensor removal steps
6. Rear toothed rotor
(Refer to GROUP 27-Rear Axle Hub.)7. Clip
8. Cable band
9. Rear speed sensor connection
4I) W 10. Rear speed sensor12. O-ring
NOTE(1) Reverse the removal procedures to reinstall.(2) +e : Refer to “Service Points of Removal”.
(3) I)+ : Refer to “Service Points of Installation”.(4) m : Non-reusable parts

Care must be taken not to scratch or scar the rotor’stoothed surface, and not to drop it.
If the rotor’s toothed surface is chipped or the rotor is
deformed, it might not be able to accurately sense the
wheel rotation speed and the system as a result might
__ r-14A¬ perform normally.
4. REMOVAL OF FRONT SPEED SENSORRemove the mounting bolts which hold the speed sensor
bracket to the knuckle, and then remove the speed sensor.
Caution
5-82BRAKES - Wheel Speed Sensor SERVICE POINTS OF REMOVAL
1. REMOVAL OF THE FRONT TOOTHED ROTOReRefer to GROUP Z-Hub and Knuckle.
Caution
Be careful when handling the pole piece at the tip of
the speed sensor and the toothed edge of the rotor so
as not to damage them by striking against other parts.
II14A0215
+ont weed sensor Rear meed sensor
Pole
piecePole piece14R0144
6. REMOVAL OF REAR TOOTHED ROTOR’For FWD vehicles refer to GROUP
17-Rear Axle Hub, for
AWD vehicles refer to GROUP
3-Axle Shaft.
Cautionr*
Care must be taken not to scratch or scar the rotor’stoothed surface, and not to drop it.
If the rotor’s toothed surface is chipped or the rotor is
deformed, it might not be able to accurately
sense the
wheel rotation speed and the system as a result might
not perform normally.
10. REMOVAL OF REAR SPEED SENSORRemove the speed sensor bracket and rear axle spindle
installation nut, and then remove the speed sensor.
Caution
Be careful when handling the pole piece at the tip of
the speed sensor and the toothed edge of the rotor
SO
as not to damage them by striking against other parts.
INSPECTION
SPEED SENSOR CHECK
(1) Check whether any metallic foreign material has adhered to
the pole piece at the speed sensor tip, and, is so, remove it.Also check whether the pole piece is damaged, and, if so,
hreplace it with a new one.
‘J

BRAKES - Wheel Speed Sensor 5-83
Front
Rear

14AO04814R0146
0R
Qfs0
0 (-Jor
L/
14AOO47
NOTEThe pole piece can become magnetized because of the
magnet built into the speed sensor, with the result that
metallic foreign material easily adheres to it. Moreover, the
pole piece may not be able to function to correctly sense
the wheel rotation speed if it is damaged.
(2) Measure the resistance between the speed sensor termi-
nals.Standard value:
0.8-1.2 kQIf. the internal resistance of the speed sensor is not within
the standard value, replace it with a new speed sensor.
(3) Check the speed sensor cable for breakage, damage or
disconnection; replace with a new one if a problem is
found.
NOTE
When checking for cable damage, remove the cable clamppart from the body and then bend and pull the cable near
the clamp to check whether or not temporary disconnec-
tion occurs.
TOOTHED ROTOR CHECKCheck whether rotor teeth are broken or deformed, and, if so,
replace the rotor.
SERVICE POINTS OF INSTALLATION
11. INSTALLATION OF REAR SPEED SENSOR BRACKET
Assemble the speed sensor and the speed sensor bracket.
NOTEThe shape is different for the left and right speed sensor
brackets. Each bracket has an identification symbol, so be
sure to note these symbols and install correctly.
R: Indicates that the bracket is for the right wheel.
L: Indicates that the bracket is for the left wheel.

5-84BRAKES - Wheel Speed Sensor Left side view
Right side
14AOO4:Left side view
Left side
14A004.fCrossmember
10. INSTALLATION OF REAR SPEED SENSOR (1) Teimn;rarily install the speed sensor to the rear axle
Caution
Be careful when handling the pole piece at the tip of
the speed sensor and the toothed edge of the rotor
so as not to damage them by striking against metal
objects.(2) Note the following points when connecting the speed
sensor cable, and secure the cable by the clip.
@I Secure the clip so that the white-painted part
(shaded in the illustration) of the speed sensor cableis not twisted.
@ Be sure that there is space (where shown in the
illustration) so that the trailing arm and speed
sensor cable do not contact, and then secure by the
clip.
Caution
Because there is the possibility of damage to the
cable during driving if the speed sensor cable and
the trailing arm come into contact, or if the speed
sensor cable is twisted, care must be taken regard-
ing this point.(3) Insert a feeler gauge into the space between the speed
sensor’s pole piece and the rotor’s toothed surface, andthen tighten the speed sensors at the position where
the clearance is the standard value.
Standard value:
0.3-0.9 mm (.012-.035 in.)
NOTECheck to be sure that there is no contact of the speed
sensor’s pole piece and the rotor’s toothed surface
when the rear hub assembly is slowly rotated one time.
If there is contact, it is probable that the rotor or the rearhub is installed incorrectly, recheck installation.
10. INSTALLATION OF REAR SPEED SENSOR Install the rear speed sensors as shown in the illustration.
Cross-section A-AParking cable
Rear
spe/edsensor12A0075
Cross-section B-B
Cross-section C-CRear speed
sensor
VA007412AOO7612AOO77

BRAKES - Wheel Speed Sensor 545
14LOl89
Cross-section A-ACross-section B-B
12R015i
5. INSTALLATION OF FRONT SPEED SENSOR BRACKET
Assemble the speed sensor and the speed sensor bracket.
NOTE(1) The shape is different for the left and right speed
sensor brackets. Each bracket has an identification
symbol, so be sure to note these symbols
ahd. install
correctly.
FR: Indicates that the bracket is for the front speed
sensor.R: Indicates that the bracket is for the right wheel.
L: Indicates that the bracket is for the left wheel.
(2) Check to be sure, when installing the speed sensor to
the bracket, that the letters “FR” are visible.
4. INSTALLATION OF FRONT SPEED SENSOR(1) Temporarily install the speed sensor to the knuckle.Caution
Be careful when handling the pole piece at the tip of
the speed sensor and the toothed edge of the rotor
so as not to damage them by striking against other
parts.(2) Note the following points when connecting the speed
sensor cable, and secure the cable by the clip.
@ Secure the cable by the clip so that the white-
painted parts of the blackened parts (in the illustra-
tion) of the speed sensor cable are within the rangeof the angles indicated by cross-section A-A and
cross-section B-B in the illustration.
@ Check to be sure that the white-painted part
(shaded in the illustration) of the speed sensor cableis not twisted.Caution
Because there is the possibility of damage to the
cable during driving if the speed sensor cable is
twisted, care must be taken regarding thispoint.
(3) Insert a feeler gauge into the space between the speed
sensor’s pole piece and the rotor’s toothed surface, and
then tighten the speed sensor at the position where theclearance is the standard value all around.Standard value:
0.3-0.9 mm (.012-.035 in.)
NOTE
If the clearance between the speed sensor’s pole pieceand the rotor’s toothed surface is not within the
standard value range, it is probable that the rotor is
incorrectly installed, recheck installation.

BRAKES - G-sensor
G-SENSOR N&OVA8
REMOVAL AND INSTALLATION
14AO595
NOTEReverse the removal procedures to reinstall.
G-sensor removal steps
1. Wiring harness connector
2. G-sensor3. G-sensor bracket
14AO194
14A0195
INSPECTION
(1)Place the sensor on a level surface, then check that there isconductance between the terminals.
(2) Slowly inclining the G-sensor in the direction of forward
vehicle travel, check that there is no conductance above a
sensor angle of 30 degrees.

BRAKES - G-sensor /Electronic Control Unit 5-87
I
14AO198(3) Slowly inclining the G-sensor in the direction of reverse
vehicle travel, check that there is no conductance above a
sensor angle of 30 degrees.
ELECTRONIC CONTROL UNIT ABS>NOSOZAEREMOVAL AND INSTALLATION
Pre-removal Operation
@Removal of the Quarter Trim (R.H.)(Refer to GROUP 23-Trim.)IPost-installation Operation
4*Installation of the
Quarter TrimI1 (RIt?.) (Refer to GROUP 23-Trim.)1
14AO584
Removal steps
4*1. Electronic control unit connection
l +2. Electronic control unit3. Bracket
NOTE(I) Reverse the removal procedures to reinstall.(2) 4e : Refer to “Service Points of Removal”.(3) l + : Refer to “Service Points of Installation”.
SERVICE POINTS OF REMOVAL
1. DISCONNECTION OF ELECTRONIC CONTROL UNIT
Unlock the connector and take the connector out.

7-l
COOLING
CONTENTS
ENGINE COOLANT TEMPERATURE GAUGEUNIT,
ENGINE COOLANT TEMPERATURE
SENSOR AND ENGINE COOLANT
TEMPERATURE SWITCH................................34
RADIATOR.......................................................12
RADIATORFANMOTOR ASSEMBLY..........15
SERVICE ADJUSTMENT PROCEDURES.......8
Alternatormater Pump Drive Belt Tension
Adjustment
....................................................9Alternator/Water Pump Drive Belt Tension
Inspection..
....................................................8Cap Pressure Test
.......................................8Engine Coolant Concentration Test
.............8
EngineCoolantLeakCheck........................8Engine Coolant Replacement
.......................8
SPECIFICATIONS.............................................2
GeneralSpecifications..................................2
Lubricant.......................................................4
Sealant..........................................................4Service Specifications
...................................2Torque Specifications
...................................3THERMOSTAT
.................................................15
TROUBLESHOOTING......................................5
Noriseintemperature................................5
Overheat.......................................................5
WATER HOSE AND WATER PIPE
<1.8L Engine>................................................25
WATER HOSE AND WATER PIPE
<2.0LDOHCEngine(Non-Turbo)>.............28
WATER HOSE AND WATER PIPE
<2.0LDOHCEngine(Turbo)>....................31
WATERPUMP<1.8LEngine>.....................17
WATER PUMP <2.0L DOHC Engine>.........21

7-2COOLING - Specifications
SPECIFICATIONS
GENERAL SPECIFICATIONSIcNQ7cA- I
ItemsCooling method
Radiator
TypeRadiator fan motor
TypeWater pump
Type
Thermostat
TypeIdentification mark
Drive belt
TypeEngine coolant temperature gauge unit
WeEngine coolant temperature sensor (Engine control)
TypeEngine coolant temperature switch (Air conditioner)
WeSpecifications
Water-cooled, pressurized, forced circulation
with electrical fan
Pressurized corrugated fin type
Direct current ferrite type
Impeller of centrifugal type
Wax pellet type with jiggle valve
88 (Stamped on flange)
V-ribbed belt
Thermistor type
Thermistor type
Thermistor type
SERVICE SPECIFICATIONSN07CB.-
Items
Standard valueRange of coolant antifreeze concentration
%
ThermostatValve opening temperature of thermostat
“C (“F)Full-opening temperature of thermostat
“C (“F)Opening pressure of cap high pressure valve
kPa (psi)
Therm0 sensor (on radiator)
Operating temperature
OFF
+ ON“C (“F)ON
--P OFF“C (“F)Engine coolant temperature gauge unit
ResistanceAt
70°C (158°F) QEngine coolant temperature sensor (Engine control)
ResistanceAt
20°C (68°F) kQAt
80°C (176°F) QEngine coolant temperature
switch (Air conditioner)
ON -+ OFF operating temperature
“C (“F)Limit
Opening pressure cap high pressure valve
kPa (psi)
Specifications
30-6088 (190)
100 (212) or more
75-105 (11-15)
82-88 (180-190)
78 (172) or less
104f 13.5
2.45
I!I 0.24
296
+ 32
112-l 18 (234-244)
65 (9.2)

COOLING - Specifications7-3
TORQUE SPECIFICATIONSN07CG.
ItemsRadiator insulator
upperThermosensor to radiator
Automatic transaxle oil cooler hose cramp
Automatic transaxle oil cooler hose mounting bolt
Water outlet fitting bolts
Engine mount insulator nut (large)
Engine mount insulator nut (small)
Engine mount bracket to engine
Bracket between engine mount bracket and engine
Tension pulley bracket for air conditioner
<1.8L Engine>
Water pump installation bolt
Bolt head mark “4T”
Bolt head mark “7T”
Water pulley bolt
pumpDamper pulley, crankshaft pulley
<1.8L Engine>
<2.0L DOHC Engine>
Timing belt front upper cover installation bolt
Timing belt front lower cover installation bolt
Crankshaft sprocket installation bolt
Timing belt
B tensioner
Tension pulley bracket for air conditioner
<2.0L DOHC Engine>
Automatic tensioner installation bolt
Tensioner pulley installation bolt
Oil level
gaugeFront exhaust pipe to exhaust manifold

Front exhaust pipe bracket
Exhaust manifold cover (A)

Flange bolt: 8
x 12 mm (.31 x .47 in.)
Washer assembled bolt: 6
x 14 mm (.24x.55in.)
<2.0L DOHC Engine (Non-Turbo)>
Exhaust manifold cover
(8)
Heat protecter (A)
Heat protecter
(B)
Exhaust manifold to cylinder head<1.8L Engine>
<2.0L DOHC Engine>
Engine hanger to engine bracket
JVater inlet pipe installation bolt
Transaxle side
Engine block side
<1.8L Engine>
<2.0L DOHC Engine>
'ower steering oil pump to oil pump bracket
‘ower steering oil pump bracket to engine
Nmft.lbs.
9-14
7-103-4
2-3
4-63-4
3-52-4
17-2012-14
60-8043-58
30-4022-29
50-6536-47
17-2612-19
18-2213-15
12-15
9-11
20-2714-20
8-106-7
15-18
11-13
20-3014-22
IO-127-9
10-127-9
110-13080-9415-22
11-16
23-27
17-20
20-2714-2043-55
31-4012-15
9-11
30-4022-29
40-6029-43
30-4022-29
27-33
20-24
8-106-7
12-15
9-11
12-15
9-11
12-15
9-11
12-15
9-l 1
15-2011-14
25-3018-22
12-15
9-11
43-55
31-40
IO-127-9
12-15
9-11
35-4525-33
25-3318-24