brake fluid MITSUBISHI ECLIPSE 1993 User Guide

BRAKES -Front Disc Brake
l-Pad and wear
indicator assembly Pad assembly
Inner
shim
Outershim
11Inner shim
Outer shim
GreaseGrease14FOO97
al
14LO127Brake fl
Grease
14LO128GreaseSERVICE
POINTS OF REASSEMBLYNW7. INSTALLATION OF INNER
SHIM/13. OUTER SHIM
Coat the mounting surfaces of the pad and inner shim
a
the mounting surface of the inner shim and outer shim vv
repair kit grease, and assemble them.
Coat grease with care to prevent swelling.Specified grease: Repair kit grease (orange)
Caution
Prevent oily materials and other dirt from sticking,
the friction surfaces of the pad and brake disc.12.APPLlCATlON OF BRAKE FLUID TO CALIPER
BODjApply specified brake fluid to inner cylinder.,.;Specified brake fluid: MOPAR Brake Fluid/;:ti
”Conforming to
DOT3 or DOT4
10. INSTALLATION OF PISTON SEAL..I.‘”Install piston seal in cylinder groove.Caution
Do not wipe special grease on piston seal.
9. INSTALLATION OF PISTON.
(1) Apply specified brake fluid to piston.
Insert into cylindlwithout twisting.
(/ifiL-_. i//Specified brake fluid: MOPAR Brake Fluid/
Conforming to
DOT3
or
DOT4(2) Fill piston edge with specified grease. Install pistc
boots.Specified grease: Repair kit grease (orange)
6. APPLICATION OF GREASE TO BOOT/3. BUSHING-’
Grease parts as illustrated with specified grease.Specified grease: Repair kit grease (orange)

BRAKES - Front Disc Brake/Rear Disc Brake5-852. INSTALLATION~OF LOCK PIN/l. GUIDE PIN
Install the guide pin and lock pin so the identification mark
on the caliper body and head mark on the guide pin and
lock pin are aligned.
.+AR msc BRAKEREMOVAL AND INSTALLATION
Pre-removal Operationl Draining of Brake Fluid

9-14 Nm7-10 ft.lbs.
50-60 Nm
36-43 ft.lbs.
/Post-installation Operation
*Supplying Brake Fluid
l Bleeding(Refer to P.5-50.)*Adjustment of Parking Brake Lever
Stroke
(Refer to P.5-48.)
200-260 Nm144-188 ft.lbs.13-17 Nm
9-12 ft.lbs.
/ -29-14
Nh7- 10 ftlbs.
Removal steps
1. Parking brake cable connection
2. Brake hose connection
3. Rear brake assembly
4. Rear brake disc
5. Hubcap
l 6. Wheel bearing nut
14AO5747. Washer
8. Rear speed sensor bracket

9. Rear hub assembly14. Dust shieldI ‘: I
FyEeverse the removal procedures to reinstall.
(2) +* : Refer to “Service Points of Removal”.,,
(3) l + : Refer to “Service Points pt(4) m : Non-reusable parts:lpstallation
../ ‘E-w,,,

5-86
BRAKES - Rear Disc Btike55-65 Nm
50-60 Nm
36-43 ft.lbs.9-14 Nm
2Pre-removal Operation
*Draining of Brake Fluid
Removal steps
1. Parking brake cable connection
4*2. Brake hose connection
3. Rear brake assembly
4. Rear brake disc
+e l * 10. Self locking nutl * 11. Companion flange
12. Rear speed sensor
ABS>
*e ++ 13. Rear axle shaft
14. Dust shieldPost-installation Operation
@Supplying Brake Fluid@Bleeding(Refer to P.5-50.)l Adjustment of Parking Brake LeverStroke
(Refer to P.5-48.)
NOTE(1) Reverse the removal procedures to reinstall.
(2) +* : Refer to “Service Points of Removal”.
(3) I)+ : Refer to “Service Points of Installation”.
(4) q : Non-reusable parts