window MITSUBISHI ECLIPSE 1993 Workshop Manual

BODY
CONTENTS
,I
i
1AEROPARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
; CENTRAL DOOR LOCKING SYSTEM . . . . . . . . . . .68
’DOORASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
DOOR GLASS AND REGULATOR................
64
DOOR HANDLE AND LATCH.....................67QUARTER WINDOWGLASS..
...............
..i..59
REAR BUMPER........................................41
REARSEAT.........................................;..93
SEATBELT.............................................
94
SERVICE ADJUSTMENT PROCEDURES........30
Door Adjustment....................................31
Door Glass Adjustment............................31
Door Inside Handle Play Check...................31
Door Outside Handle Play Check................31
Floor PanInspection..............................
32
Fuel Filler Door Adjustment.......................30
Hood Adjustment...................................30
Liftgate Adjustment.................................30
Water Test...........................................
32
SPECIAL TOOLS....................*..........c......
5
SPECIFICATIONS.....................................2
General Specifications...........................;..2
Lubricants.............................................5
Sealants and Adhesives...........................5
Service Specifications..............................3
Torque Specifications..............................3
SUNROOF...............................................
77
TRIMS....................................................
85
TROUBLESHOOTING................................6
WINDOWGLASS.....................................52
WINDSHIELD...........................................56
DOORMIRROR........................................
70
DOOR
MOULDING AND
DRIP LINE WEATHERSTRIP........................
70
DOORRUNCHANNEL...............................
69
DOOR TRIM AND WATERPROOF FILM........
63
ELECTRIC REMOTE CONTROLLED
MIRRORSWITCH.....................................
71
FENDER..................................................
49
FLOORCONSOLE....................................
84
FRONTBUMPER......................................37
FRONTSEAT...........................................90
FUEL TANK FILLER DOOR.........................
36
GARNISHES............................................45
HEADLINING...........................................89
HOOD....................................................
33
INSTRUMENTPANEL.,..............................
79
Lll=l’GATE...............................................
35
LIFTGATE WINDOW GLASS......................60
LOOSEPANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
MOULDING.............................................
46
POWERWINDOW....................................65
N23AA--

23-46BODY - Moulding
MOULDING
REMOVAL AND INSTALLATION
WA0954
N23REIU1. Drip moulding
2. Windshield upper moulding
z3. Quarter window moulding lower
4. Quarter window moulding upper
4*5. Quarter window moulding front
:+’6.
Liftgate moulding lower
7. Liftgate moulding upper
4*8. Liftgate moulding side+e+* 9. Side protect moulding fender4+1)+10. Side protect moulding front door4**+11. Side protect moulding quarter
NOTE(1) a* : Refer to “Service Points of Removal”.12) l + : Refer to “Service Pdints of Installation”.
SERVICE POINTS OF REMOVAL
1. REMOVAL OF DRIP MOULDING
Refer to
P.23-70.2. REMOVAL OF WINDSHIELD UPPER MOULDING
Refer to
P.23-56.

BODY - Moulding23-47
?8UO387
3.REMOVAL OF QUARTER WINDOW MOULDING LOWER/
4. QUARTER WINDOW MOULDING UPPER/B. QUARTER
WINDOW MOULDING FRONTRefer to P.23-59.
6. REMOVAL OF
LIFTGATE MOULDING LOWER17. LIFT-GATE MOULDING
UPPER/8. LIFTGATE MOULDING
SIDERefer to P.23-60.
9. REMOVAL OF SIDE PROTECT MOULDING FENDER/
10. SIDE PROTECT MOULDING FRONT DOOR/l 1.
REMOVAL OF SIDE PROTECT MOULDING QUARTER(1) Using the plastic trim tool, pry off the side protect
moulding.(2) Using the
ptastic trim tool, scale off the both-side
adhesive tape which sticks to the body.
SERVICE POINTS OF INSTALLATION
9. INSTALLATION OF SIDE PROTECT MOULDING FEN-
DER/10. SIDE PROTECT MOULDING FRONT DOOR/11. SIDE PROTECT MOULDING QUARTER
(1) Wipe off application surface of body with clean cloth
dampened with degreaser (MOPAR SUPER KLEEN or
equivalent).
NOTEAfter wiping surface, leave surface as it is to volatilize
degreaser.(2) Using an infrared light or similar instrument, heat the
body painted surface and the side protect moulding.
Heating temperature
Body painted surface..,.. 25-55OC (77-131OF)
Side protect moulding....
25-40°C (77-104OF)