MITSUBISHI ENDEAVOR 2004 Service Repair Manual

Fig. 250: Locating Connectors C
-211 And C
-215

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

STEP 4. Measure the voltage at A/C-ECU connector C-17.

1. Disconnect A/C-ECU connector C-17 and measure the voltage at the
harness side.
2. Turn the ignition switch to the "ACC" position.
Fig. 251: Locating Connector C
-17
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

3. Measure the voltage between terminal 36 and ground.
The measured value should be approximately 12 volts (battery
positive voltage).

2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

Fig. 252: Measuring Voltage Between Terminal 36 And Ground

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

Q: Is the measured voltage approx. 12 volts?

YES:
Go to Step 6 .
NO:
Go to Step 5.
STEP 5. Check the wiring harness between A/C-ECU connector C-17
(terminal 36) and the ignition switch (ACC).


2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

Fig. 253: Identifying Connector C
-17
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

Q: Is the wiring harness between A/C-ECU connector C-17 (terminal 36)
and the ignition switch (ACC) in good condition?

YES:
It can be assumed that this malfunction is intermittent.
Refer to
HOW TO USE TROUBLESHOOTING/ INSPECTION
NOTE: Also check joint connector C-104 and intermediate
connector C-31 for loose, corroded, or damaged
terminals, or terminals pushed back in the connector. If
joint connector C-104 or intermediate connector C-31 is
damaged, repair or replace the connector as described
in HARNESS CONNECTOR INSPECTION
.

2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

SERVICE POINTS
.
NO:
Repair the wiring harness. Check that the air conditioning works
normall
y.

2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

Fig. 254: Locating Connectors C
-104 And C
-31
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

STEP 6. Measure the voltage at A/C-ECU connector C-16.

1. Disconnect A/C-ECU connector C-16 and measure the voltage at the
harness side.
Fig. 255: Locating Connector C
-16
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2. Measure the voltage between terminal 3 and ground.
The measured value should be approximately 12 volts (battery positive volta
ge).

2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

Fig. 256: Measuring Voltage Between Terminal 3 And Ground

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

Q: Is the measured voltage approx. 12 volts?

YES:
Go to Step 8 .
NO:
Go to Step 7.
STEP 7. Check the wiring harness between A/C-ECU connector C-16
(terminal 3) and the battery.

2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

Fig. 257: Locating Connector C
-16
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

Q: Is the wiring harness between A/C-ECU connector C-16 (terminal 3)
and the battery in good condition?

YES:
It can be assumed that this malfunction is intermittent.
NOTE: Also check joint connector C-04 and intermediate
connector C-31 for loose, corroded, or damaged
terminals, or terminals pushed back in the connector. If
joint connector C-04 or intermediate connector C-31 is
damaged, repair or replace the connector as described
in HARNESS CONNECTOR INSPECTION
.

2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

Refer to
HOW TO USE TROUBLESHOOTING/ INSPECTION
SERVICE POINTS
.
NO:
Repair the wiring harness. Check that the air conditioning works
normall
y.

2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor

Fig. 258: Locating Connectors C
-04 And C
-31
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 HVAC Heater Air Conditioning, Ventilation - Endeavor