Abs sensor MITSUBISHI ENDEAVOR 2004 Service Owner's Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2004, Model line: ENDEAVOR, Model: MITSUBISHI ENDEAVOR 2004Pages: 3870, PDF Size: 98.47 MB
Page 65 of 3870
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
2. Turn the ignition switch to the "ON" position.
3. Check whether DTC C1200, C1205, C1210 or C1215 have been set.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC C1200, C1205, C1210 or C1215 set?
YES: Carry out diagnosis relevant to DTC C1200, C1205, C1210 or
C1215 (Refer to DIAGNOSTIC TROUBLE CODE PROCEDURES
).
NO: Go to Step 4.
STEP 4. Check the installation condition of the ABS sensors.
For the ABS sensor, which the DTC code indicates, check whether the sensor
or its mounting bolts are loosened.
DTC C1201 is set: Front right ABS sensor DTC C1206 is set: Front left ABS sensor DTC C1211 is set: Rear right ABS sensor DTC C1216 is set: Rear left ABS sensor
Q: Is the ABS sensor installed correctly?
YES: Go to Step 5.
NO: Reinstall the ABS sensor correctly. Then go to Step 16 .
STEP 5 Check the ABS sensor after it is removed from the vehicle.
Check the ABS sensor, which the DTC code indicates (Refer to
INSPECTION
).
DTC C1201 is set: Front right ABS sensor DTC C1206 is set: Front left ABS sensor DTC C1211 is set: Rear right ABS sensor DTC C1216 is set: Rear left ABS sensor
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 66 of 3870
Q: Is the ABS sensor in good condition?
YES: Go to Step 6.
NO: Replace the ABS sensor. Then go to Step 16 .
STEP 6. Check the wheel bearing for looseness.
DTC C1201 is set: Check the front right wheel bearing (Refer to WHEEL BEARING END PLAY CHECK
).
DTC C1206 is set: Check the front left wheel bearing (Refer to WHEEL BEARING END PLAY CHECK
).
DTC C1211 is set: Check the front right wheel bearing (WHEEL BEARING END PLAY CHECK
). < AWD > Refer to WHEEL
BEARING END PLAY CHECK
).
DTC C1216 is set: Check the rear left wheel bearing (< FWD > Refer to
WHEEL BEARING END PLAY CHECK
). < AWD > Refer to
WHEEL BEARING END PLAY CHECK ).
Q: Is the wheel bearing end play is not within the standard value?
YES: Go to Step 7.
NO (front bearing end play is not within the standard value): Replace
the front hub assembly (Refer to, FRONT AXLE HUB ASSEMBLY
).
Then go to Step 16 .
NO (rear bearing end play is not within the standard value < FWD >):
Replace the rear hub assembly (Refer to REAR AXLE HUB
ASSEMBLY
). Then go to Step 16 .
NO (rear bearing end play is not within the standard value < AWD
>): Replace the rear hub assembly (Refer to , REAR AXLE HUB
ASSEMBLY ). Then
go to Ste
p 16. NOTE: If the wheel bearing is loose, the gap between the ABS
sensor and rotor may become excessive. Check the
wheel bearing, which DTC code indicates, for
looseness.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 67 of 3870
STEP 7. Check the ABS rotor.
Check the ABS rotor, which DTC code indicates, for foreign material or
deformation.
DTC C1201 is set: Front right ABS sensor DTC C1206 is set: Front left ABS sensor DTC C1211 is set: Rear right ABS sensor DTC C1216 is set: Rear left ABS sensor
Q: Is the ABS rotor in good condition?
YES: Go to Step 8.
NO (front bearing end play is not within the standard value): If the
ABS rotor is contaminated with foreign material, clean it. If the driveshaft
is deformed, replace it (Refer to DRIVE SHAFT ASSEMBLY
, ). Then
go to Step 16 .
NO (rear bearing end play is not within the standard value < FWD >):
If the ABS rotor is contaminated with foreign material, clean it. If the
ABS rotor is deformed, replace it (Refer to REAR AXLE HUB
ASSEMBLY
, ). Then go to Step 16 .
NO (rear bearing end play is not within the standard value < AWD
>): If the ABS rotor is contaminated with foreign material, clean it. If the
BJ assembly is deformed, replace it (Refer to DRIVE SHAFT
ASSEMBLY
). Then go to Step 16 .
STEP 8. Measure the voltage at ABS-ECU connector A-02.
1. Disconnect the connector A-02, and connect special tool ABS Check
Harness (MB991970) to the wiring harness-side connector.
NOTE: Do not connect special tool ABS Check Harness
(MB991970) to the ABS-ECU.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 69 of 3870
2. Turn the ignition switch to the "ON" position.
3. Measure the voltage between the relevant signal and ground terminals in
the ABS sensor circuit and body ground. It should be less than 1V.
DTC C1201 is set: Between signal terminal 9 and body ground, and
between ground terminal 10 and body ground DTC C1206 is set: Between signal terminal 26 and body ground, and
between ground terminal 16 and body ground DTC C1211 is set: Between signal terminal 11 and body ground, and
between ground terminal 17 and body ground DTC C1216 is set: Between signal terminal 28 and body ground, and
between ground terminal 27 and body ground
Q: Does the voltage measure 1 V or less?
YES: Go to Step 9.
NO (When the voltage between terminal 9 or 10 - and body ground
measures more than 1 V): Go to Step 11 .
NO (When the voltage between terminal 26 or 16 - and body ground
measures more than 1 V): Go to Step 12 .
NO (When the voltage between terminal 11 or 17 - and body ground
measures more than 1 V): Go to Step 13 .
NO (When the voltage between terminal 28 or 27 - and body ground
measures more than 1 V): Go to Step 14 .
STEP 9. Measure the resistance at ABS-ECU connector A-02.
1. Disconnect the connector A-02, and connect special tool ABS Check
Harness (MB991970) to the wiring harness-side connector.
2. Measure the resistance between the relevant signal and ground terminals
in the ABS sensor circuit and body ground. OK if there is no continuity. DTC C1201 is set: Between signal terminal 9 and bo
dy ground, and NOTE: Do not connect special tool ABS Check Harness
(MB991970) to the ABS-ECU.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 72 of 3870
Q: Does continuity exist?
YES (Continuity exists between terminal 9 or terminal 10 and body
ground): Go to Step 11 .
YES (Continuity exists between terminal 26 or terminal 16 and body
ground): Go to Step 12 .
YES (Continuity exists between terminal 11 or terminal 17 and body
ground): Go to Step 13 .
YES (Continuity exists between terminal 28 or terminal 27 and body
ground): Go to Step 14 .
NO: Go to Step 10.
STEP 10. Measure the resistance at ABS-ECU connector A-02.
1. Disconnect the connector A-02, and connect special tool ABS Check
Harness (MB991970) to the wiring harness-side connector.
2. Measure the resistance between the relevant signal and ground terminals
in the ABS sensor circuit.
DTC C1201 is set: Between signal terminal 9 and ground terminal 10 DTC C1206 is set: Between signal terminal 26 and ground terminal
16 DTC C1211 is set: Between signal terminal 11 and ground terminal
17 DTC C1216 is set: Between signal terminal 28 and ground terminal
27
Standard Value: 1.24 - 1.64 kohm NOTE: Do not connect special tool ABS Check Harness
(MB991970) to the ABS-ECU.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 74 of 3870
Q: Is the resistance between terminals 16 and 26, 9 and 10, 27 and 28, or
11 and 17 within the standard value?
YES (When resistance between all terminals are within the standard
value): Go to Step 15 .
NO (When resistance between terminals 9 and 10 is not within the
standard value): Go to Step 11.
NO (When resistance between terminals 16 and 26 is not within the
standard value): Go to Step 12 .
NO (When resistance between terminals 11 and 17 is not within the
standard value): Go to Step 13 .
NO (When resistance between terminals 27 and 28 is not within the
standard value): Go to Step 14 .
STEP 11. Check ABS-ECU connector A-02 and ABS sensor < front: RH >
connector A-31 for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 76 of 3870
Fig. 46: Checking ABS Sensor Connector A
-31
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are ABS-ECU connector A-02 and ABS sensor < front: RH >
connector A-31 damaged?
YES: Repair or replace the damaged component(s). Then go to Step 16 .
NO: Open or short circuit may be present in the front right ABS sensor
circuit. Repair the wiring harness between ABS-ECU connector A-02
(terminals 9 and 10) and front right ABS sensor A-31 (terminals 2 and 1).
Then go to Step 16 .
STEP 12. Check ABS-ECU connector A-02 and ABS sensor < front: RH >
connector A-14 for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 78 of 3870
Fig. 48: Checking ABS Sensor Connector A
-14
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are ABS-ECU connector A-02 and ABS sensor < front: LH >
connector A-14 damaged?
YES: Repair or replace the damaged component(s). Then go to Step 16 .
NO: Open or short circuit may be present in the front right ABS sensor
circuit. Repair the wiring harness between ABS-ECU connector A-02
(terminals 16 and 26) and front left ABS sensor A-14 (terminals 1 and 2).
Then go to Step 16 .
STEP 13. Check ABS-ECU connector A-02, intermediate connector C-32
and ABS sensor < Rear: RH > connector D-10 for loose, corroded or
damaged terminals, or terminals pushed back in the connector.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 81 of 3870
Fig. 51: Checking ABS Sensor Connector D
-10
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are ABS-ECU connector A-02, intermediate connector C-32 and ABS
sensor < Rear: RH > connector D-10 damaged?
YES: Repair or replace the damaged component(s). Then go to Step 16 .
NO: Open or short circuit may be present in the rear right ABS sensor
circuit. Repair the wiring harness between ABS-ECU connector A-02
(terminals 11 and 17) and rear right ABS sensor D-10 (terminals 1 and 2).
Then go to Step 16 .
STEP 14. Check ABS-ECU connector A-02, intermediate connector C-32
and ABS sensor < rear: LH > connector D-15 for loose, corroded or
damaged terminals, or terminals pushed back in the connector.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor
Page 84 of 3870
Fig. 54: Checking ABS Sensor Connector D
-15
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are ABS-ECU connector A-02, intermediate connector C-32 and ABS
sensor < rear: LH > connector D-15 damaged?
YES: Repair or replace the damaged component(s). Then go to Step 16 .
NO: Open or short circuit may be present in the rear left ABS sensor
circuit. Repair the wiring harness between ABS-ECU connector A-02
(terminals 27 and 28) and rear left ABS sensor D-10 (terminals 2 and 1).
Then go to Step 16 .
STEP 15. Recheck for diagnostic trouble code.
Check again if the DTC is set.
1. Turn the i
gnition switch to the "ON"
position.
2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor