heating MITSUBISHI ENDEAVOR 2010 1.G User Guide

4-20 Driving safety
4
When towing at high altitudes, engine coolant and automatic
transaxle fluid will overheat at a lower temperature than at nor-
mal altitudes.
If you turn your engine off immediately after towing at high
altitude on steep uphill grades, your vehicle may show signs
similar to overheating. To avoid this, let the engine run while
parked (preferably on level ground) with the automatic tran-
saxle in “P” (PARK) position for a few minutes before turning
the engine off.

If the needle in the engine coolant temperature gauge
approaches the overheating zone, refer to “Engine over-
heating” on page 6-5.

If the automatic transaxle fluid temperature warning light
illuminates, refer to “Automatic transaxle fluid tempera-
ture warning light” on page 3-43.Driving on hillsReduce speed and shift to a lower gear before you start down a
long or steep downgrade. If you don’t shift down, over using
the brakes can cause reduced brake efficiency.
You can tow in “D” (DRIVE) position. You may want to shift
the transaxle to 3rd gear or a lower gear, under heavy loads or
hilly conditions.
ParkingAlways place chocks or blocks under both the vehicle and
trailer wheels when parking. Apply the parking brake firmly.
Move the selector lever to the “P” (PARK) position. Avoid
parking on a hill with a trailer, but if it cannot be avoided, do so
only after performing the following:
1. Apply the brakes and keep them applied.
2. Have someone place chocks or blocks under both the
vehicle and trailer wheels.
3. When the chocks or blocks are in place, release your
brakes slowly until the chocks or blocks absorb the load.
4. Apply the parking brake firmly.
5. Move the selector lever to the “P” (PARK) position and
turn off the engine.
When restarting out after parking on a hill:
1. Make sure the selector lever is in the “P” (PARK) posi-
tion, and start the engine. Be sure to keep the brake pedal
depressed.
2. Move the selector lever to the 2nd gear, 1st gear or “R”
(REVERSE) position.
3. Release the parking brake and brake pedal and slowly pull
or back away from the chocks or blocks. Stop and apply
your brakes.
4. Have someone retrieve the chocks or blocks.
BK0102600US.book 20 ページ ２００９年３月３０日　月曜日　午後２時２分

5-10 Comfort controls
5
Operating the air conditioning system
N00731100176
Heating Set the mode selection dial to the “ ” position and set the air
selection switch (A) to the outside position.
Turn the temperature control dial clockwise or counterclock-
wise to the desired temperature. Select the desired blower
speed.
Cooling
N00731200281
For ordinary cooling

1. Set the mode selection dial to the “ ” position.
2. Set the air selection switch (A) to the outside position.
3. Push the air conditioning switch (B).
4. Change the temperature by turning the control dial clock-
wise or counterclockwise.
5. Select the desired blower speed.
BK0102600US.book 10 ページ ２００９年３月３０日　月曜日　午後２時２分

Comfort controls
5-23
5
NOTE
Set the temperature {at about 75 (Type 1) or 25 (Type 2)
under normal conditions}.

When the temperature is set to the highest or the lowest
setting under the AUTO operation, the air selection and
the air conditioning will be automatically changed as fol-
lows.
• Quick Heating (When the temperature is set to the high-
est setting)
Outside air will be introduced and the air conditioning
will stop.
• Quick Cooling (When the temperature is set to the low-
est setting)
Inside air will be recirculated and the air conditioning
will operate.

When the temperature is set to the highest setting, you can
turn the air conditioning on.
Operating the air conditioning system (manual
mode)
N00731800027
Blower speed and vent mode may be controlled manually by
setting the blower speed selection dial and the mode selection
dial to the desired positions. To return to automatic operation,
set the dials to the “AUTO” position.Defrosting or defogging the windshield and door win-
dows
N00732400310
To remove frost or fog from the windshield and door windows,
use the mode selection dial (“ ” or “ ”).
CAUTION
!
For safety, make sure you have a clear view through
all the windows.
BK0102600US.book 23 ページ ２００９年３月３０日　月曜日　午後２時２分

6
For emergencies
If the vehicle breaks down . . . . . . . . . . . . . . . . . . .6- 2
Jump-starting the engine . . . . . . . . . . . . . . . . . . . .6- 2
Engine overheating . . . . . . . . . . . . . . . . . . . . . . . .6- 5
Tools and jack . . . . . . . . . . . . . . . . . . . . . . . . . . . .6- 7
How to change a tire . . . . . . . . . . . . . . . . . . . . . . .6- 12
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6- 23
Operation under adverse driving conditions . . . . .6- 25
BK0102600US.book 1 ページ ２００９年３月３０日　月曜日　午後２時２分

For emergencies
6-5
6
As your vehicle has anti-lock brakesIf you drive your vehicle with a low battery charge, after the
engine has been started by using jumper cables, the engine may
misfire. This can cause the anti-lock braking system warning
light to blink on and off. This is only due to the low battery
voltage. It is not a problem with the brake system. If this hap-
pens, fully charge the battery and ensure the charging system is
operating properly.
Engine overheating
N00836500222
If the engine coolant temperature gauge indicator moves to the
“H” (hot) position (red zone), the engine may be overheated. If
this happens:
1. Stop the vehicle in a safe place. Turn on the hazard warn-
ing flashers.
2. With the engine still running, carefully raise the engine
hood to vent the engine compartment.
3. Check that the cooling fan is running. If the fan is not
turning, stop the engine immediately and contact an
authorized Mitsubishi Motors dealer or a repair facility of
your choice for assistance.
4. If you see steam or spray coming from under the hood,
turn off the engine.
WA R N I N G
!
To avoid personal injury, keep hands, hair, jewelry
and clothes away from the cooling fan. The cooling
fan can start at any time.
BK0102600US.book 5 ページ ２００９年３月３０日　月曜日　午後２時２分

For emergencies
6-25
6
Towing with rear wheels off the ground (Type B)Place the selector lever in the “N” (NEUTRAL) position.
Turn the ignition key to the “ACC” position and secure the
steering wheel in a straight-ahead position with a rope or tie-
down strap. Never place the ignition key in the “LOCK” posi-
tion when towing.Towing with front wheels off the ground (Type C)Release the parking brake.
Place the selector lever in the “N” (NEUTRAL) position.
Operation under adverse driving conditions
N00837200620
If your vehicle becomes stuck in sand, mud or
snow If your vehicle becomes stuck in snow, sand, or mud, it can
often be moved by a rocking motion. Move the selector lever
rhythmically between “Sports mode” and “R” (REVERSE)
position, while pressing lightly on the accelerator pedal.
Do not rev the engine or spin the wheels. Constant efforts to
free a stuck vehicle can cause overheating and transaxle fail-
ure. Let the engine idle for a few minutes to cool the transaxle
before trying again.
If your vehicle is still stuck after several rocking attempts, call
for a commercial tow truck service.
CAUTION
!
Never tow an automatic transaxle vehicle with the
rear wheels up (and the front wheels on the ground)
(Type B) when the automatic transaxle fluid level is
low. This may cause serious and expensive damage
to the transaxle.
WA R N I N G
!
To prevent entry of exhaust gas from the towing
vehicle, set your air selection switch to the recircula-
tion position.
WA R N I N G
!
When trying to rock your vehicle out of a stuck posi-
tion, make sure that there are no people nearby. The
rocking motion can make your vehicle suddenly
lurch forward or backward, and injure any
bystanders.
BK0102600US.book 25 ページ ２００９年３月３０日　月曜日　午後２時２分

Vehicle care and maintenance
7-3
7 Catalytic converter
N00937400421
The catalytic converter requires you to use unleaded fuel only.
Leaded gasoline will destroy the emission-control effective-
ness of the converter.
Normally, the catalytic converter does not require maintenance.
However, it is important to keep the engine properly tuned for
the converter to continue to work properly. To reduce the possibility of catalytic converter damage:

Use UNLEADED GASOLINE ONLY of the type of rec-
ommended in “Fuel selection”.

Do not drive with an extremely low fuel level. Running
out of gas could damage the catalytic converter.

Do not idle the engine with any spark plug wires discon-
nected or removed, such as when performing diagnostic
tests.

Do not idle the engine for a long time if it is idling
roughly or otherwise obviously malfunctioning.

To prevent the catalytic converter from being damaged
from unburned gas, do not race the engine when turning
off the ignition switch.

Stop driving the vehicle if you think the performance is
noticeably low, or the engine has a malfunction. If you are
not able to stop driving immediately, slow down and drive
for only a short time. Have an inspection made by an
authorized Mitsubishi Motors dealer or a repair facility of
your choice as soon as possible.

In unusual situations involving major engine problems, a
burning odor may indicate severe and abnormal catalytic
converter overheating. If this occurs, stop in a safe place,
shut the engine off and let the vehicle cool. Once the
engine is cool, immediately take your vehicle to an autho-
rized Mitsubishi Motors dealer or a repair facility of your
choice for service.
CAUTION
!
Damage to the catalytic converter can result if your
vehicle is not kept in proper operating condition. If
the engine malfunctions or misfires, or if your vehi-
cle performance suffers, have it serviced promptly.
Running your vehicle when it is overheated may
result in damage to the converter and vehicle.
WA R N I N G
!
Do not park or run your vehicle in areas where com-
bustible materials such as dry grass or leaves can
come in contact with a hot exhaust, since a fire could
occur.
Do not put undercoat paint on the catalytic con-
verter.
BK0102600US.book 3 ページ ２００９年３月３０日　月曜日　午後２時２分

Vehicle care and maintenance
7-35
7
and release lever. Work the grease into the hood lock mecha-
nism until all the movable surfaces are covered.
Also, put a light coat of the same grease on the safety catch
wherever moving parts touch.
For cold and snowy weather
N00942600115
Ventilation slotsThe ventilation slots in front of the windshield should be kept
clear of leaves or brushed clear after a heavy snowfall, so that
the operation of the heating and ventilation systems will not be
impaired.WeatherstrippingTo prevent freezing of the weatherstripping on the doors,
engine hood, etc., they should be treated with silicone grease.Additional equipment (For regions where snow is
encountered)It is a good idea to carry a shovel or a short-handled spade in
the vehicle during the winter so that you can clear away snow
if you get stranded. A small hand-brush for sweeping snow off
the vehicle and a plastic scraper for the windshield, side and
rear window are also useful.
BK0102600US.book 35 ページ ２００９年３月３０日　月曜日　午後２時２分

Alphabetical index
3
Hood 7-4
Malfunction indicator 3-84
Oil and oil filter 7-6
,9-8
Overheating 6-5
Serial number 9-2
Specifications 9-6
Error codes 5-72
Exhaust system 7-34
F
Filling the fuel tank 1-4
Floor console box 3-204
Fluid
Automatic transaxle fluid 7-12
,9-8
Brake fluid 7-15
,9-8
Engine coolant 7-9,9-8
Power steering fluid 7-16
,9-8
Washer fluid 7-14
,9-8
Fluid capacities and lubricants 9-8
Fog lights
Bulb capacity 7-45
Indicator 3-83
Replacement 7-49
Switch 3-158
For cold and snowy weather 7-35
Front side-marker lights
Bulb capacity 7-45
Replacement 7-48
Front turn signal lightsBulb capacity 7-45
Replacement 7-48
Fuel
Fuel economy 4-2
Fuel gauge 3-80
Fuel hoses 7-32
Fuel selection 1-2
Low-fuel warning light 3-80
Modification/alterations to the electrical or fuel systems 1-8
Tank capacity 1-5
,9-8
Full-time all-wheel drive 3-47
Fuse links 7-36
Fuses 7-36
G
Gauges 3-77
General maintenance 7-33
General vehicle data 9-4
,9-5
Genuine parts 1-9
Glove compartment 3-204
H
Hands-free Bluetooth
® cellular phone interface system with
voice recognition 3-164
Hazard warning flasher switch 3-158
Hazard warning lights 3-83
Head restraints 2-12
Headlights
Bulb capacity 7-45
BK0102600US.book 3 ページ ２００９年３月３０日　月曜日　午後２時２分

Alphabetical index
5
Engine oil 7-6
,9-8
Rear axle oil 7-14,9-8
Transfer oil 7-13
,9-8
Oil pressure warning light 3-85
Operation under adverse driving conditions 6-25
Outside rearview mirrors 3-32
Overhead console control switch 3-165
Overheating 6-5
P
Parking 4-7
Parking brake 3-28
Parking brake pedal stroke 7-30
Parking brake 7-30
Parking brake break-in 7-30
Parking lights
Bulb capacity 7-45
Replacement 7-48
Polishing 7-61
Power brakes 3-53
Power door locks 3-15
Power outlet 3-195
Power steering
Fluid 7-16
,9-8
System 3-57
Power windows 3-23
Main switch 3-24
Sub switch 3-24
Timer function 3-24Puncture (Tire changing) 6-12
R
Radiator cap 7-10
Radio
AM/FM electronically tuned radio with
CD autochanger-Type 2 5-43
AM/FM electronically tuned radio with CD player-Type 1
5-30
AM/FM/Satellite electronically tuned radio with
CD autochanger-Type 3 5-43
General information about your radio 5-78
Reading lights
Replacement 7-55
Switch 3-200
Rear axle oil 7-14
,9-8
Rear cooler 5-25
Rear personal lights
Bulb capacity 7-46
Replacement 7-56
Switch 3-201
Rear side-marker light
Bulb capacity 7-45
Replacement 7-51
Rear turn signal lights
Bulb capacity 7-45
Replacement 7-51
Rear window defogger switch 3-163
Rear-view camera 3-75
BK0102600US.book 5 ページ ２００９年３月３０日　月曜日　午後２時２分