warning MITSUBISHI GALANT 2012 9.G Owner's Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2012, Model line: GALANT, Model: MITSUBISHI GALANT 2012 9.GPages: 424, PDF Size: 61.76 MB
Page 169 of 424
3-80 Features and controls
3
Charging system warning light
N00520600209
This light comes on in the event of a malfunction in the charg-
ing system or when the ignition key is turned to the “ON” posi-
tion (engine off). When the engine is started, the light should
go out. Check to make sure that the light has gone out before
driving.Oil pressure warning light
N00520700170
This light comes on when the engine oil pressure is below nor-
mal. If the light stays on while driving, stop the engine as soon
as possible. Do not run the engine until the cause of the low oil
pressure is corrected.
Door-ajar warning light and buzzer
N00520900299
This light comes on when any door is open or not completely
closed.
When the vehicle is moving at more than 5 mph (8 km/h) and
any door is open or ajar, a tone will sound 4 times and the
warning light will flash 4 times to inform the driver that a door
is not properly shut.NOTEThe light goes out automatically after about 30 minutes.
Refer to “Interior light auto-shutoff function (dome light
and other lights)” on page 3-130.
For vehicles equipped with the Mitsubishi Multi-Commu-
nication System, Mitsubishi Multi-Communication Sys-
tem can be used to stop the warning lamp from flashing
and to stop the tone from functioning.
For details, refer to the separate owner’s manual.
CAUTION
!If the charging light stays on after the engine has
started, the battery charging system may be mal-
functioning. In this case, take your vehicle to an
authorized Mitsubishi Motors dealer or a repair
facility of your choice and have the system checked.
CAUTION
!If this light comes on when the engine oil level is not
low, have your vehicle checked at an authorized Mit-
subishi Motors dealer or a repair facility of your
choice.This warning light does not show the amount of oil
in the crankcase. This can only be determined by
checking the oil level with the dipstick with the
engine turned off.
CAUTION
!Before driving, make sure that the door-ajar warn-
ing light is off.
BK0139500US.book 80 ページ 2011年4月19日 火曜日 午後1時48分
Page 174 of 424
Features and controls
3-85
3
NOTEA light in the instrument panel flashes to show when the
front and rear turn signal lights are working properly.
If this light flashes faster than usual, check for a burned
out lamp bulb or malfunctioning connection.
If the panel light does not come on when the lever is
moved, check for a blown fuse or a burned out bulb in the
panel.
Have the vehicle inspected by an authorized Mitsubishi
Motors dealer or a repair facility of your choice.
For vehicles equipped with the Mitsubishi Multi-Commu-
nication System, Mitsubishi Multi-Communication Sys-
tem can be used to select whether the tone will sound or
not sound when the turn signal lights are activated.
For details, refer to the separate owner’s manual.
Hazard warning flasher switch
N00522700262
If you press the flasher switch, the front and rear turn signals
will flash intermittently, and so will the hazard warning lights.
This is an emergency warning system and should not be used
when the vehicle is in motion, except for emergencies.
If you need to leave your vehicle, the flashers will keep work-
ing after the ignition key is removed. NOTEIf you keep the flashers on for several hours with the
engine turned off, the battery will run down.
For vehicles equipped with the Mitsubishi Multi-Commu-
nication System, Mitsubishi Multi-Communication Sys-
tem can be used to select whether the tone will sound or
not sound when the hazard warning flashers are activated.
For details, refer to the separate owner’s manual.
BK0139500US.book 85 ページ 2011年4月19日 火曜日 午後1時48分
Page 288 of 424
Comfort controls
5-51
5
To unlock locked channels
N00701700056
You can unlock one or all locked channels. Unlocking one or
more channels requires entry of the code.NOTEThe code is set to “1111” at the factory.
It is possible to change the code to any desired number
using “CODE EDIT”.
1. If you wish to unlock a single desired channel, select the
channel you wish to unlock. (If you wish to unlock all
locked channels, it doesn’t matter which channel you
select.)
2. Push the AUDIO switch (6) for at least about two seconds
to select the MENU mode. Then select the LOCK setting
mode.
3. In the LOCK setting mode, turn the AUDIO switch (6) to
select “UNLOCK” if you wish to unlock a single desired
channel or “UNLOCK ALL” if you wish to unlock all
locked channels.
4. Push the AUDIO switch (6). The code entry window will
display.5. Use the memory select buttons (7) to enter the code (1111
to 6666).
6. If you entered the correct code, the channel lock setting
will be cancelled and the system will return to the LOCK
setting mode.
If you entered an incorrect code, a warning sound will be
emitted and “CODE E” will be displayed. Then, the code
entry window will again display. You can retry the code
entry any number of times.
BK0139500US.book 51 ページ 2011年4月19日 火曜日 午後1時48分
Page 289 of 424
5-52 Comfort controls
5
To change the lock cancellation code
N00701800057
It is possible to change the code for lock cancellation to any
desired number.
1. Push the AUDIO switch (6) for at least about 2 seconds to
select the MENU mode. Then select the LOCK setting
mode.
2. In the LOCK setting mode, turn the AUDIO switch (6) to
select “CODE EDIT”.
3. Push the AUDIO switch (6). The code entry window will
display.
4. Use the memory select buttons (7) to enter the current
code (the code prior to the change).
5. If you entered the correct code, the code entry window
will again be shown. Enter your desired code.
If you entered an incorrect code, a warning sound will be
emitted and “CODE E” will be displayed. Then, the code
entry window will again be shown. You can retry the code
entry any number of times.
6. After entering the new code, push the AUDIO switch (6).
The code entry window will again be shown for confirma-
tion. Enter the new code again, then push the AUDIO
switch (6).
7. The code will be changed, and the system will return to
the LOCK setting mode.NOTEThe code is stored in memory. If a battery cable is discon-
nected, such settings will be erased. (The code will return
to the “1111” that was set at the factory.)
To reset the lock cancellation code
N00701900045
In case you forget the code, it is possible to reset the code to the
“1111” that was set at the factory.
1. With the audio power OFF, push the PWR switch (1) and
AUDIO switch (6) simultaneously. The display will show
“CODE INITIAL”.
2. Push the AUDIO switch (6). The display will show
“YES”. If you wish to reset the code, push the AUDIO
switch (6) again. If you do not wish to reset the code, turn
the AUDIO switch (6) so the display shows “CANCEL”
and then push the AUDIO switch (6) again.
BK0139500US.book 52 ページ 2011年4月19日 火曜日 午後1時48分
Page 313 of 424
6-2 For emergencies
6If the vehicle breaks down
N00836300174
If your vehicle breaks down on the road, move to the shoulder
and turn on the hazard warning flashers. If there is no shoulder,
or the shoulder is not safe, drive in the right lane slowly, with
the hazard lights flashing, until you come to a safe stopping
place. Keep the flashers flashing. If the engine stops/fails If the engine stops, there will be no power assist to the steering
and brakes, making these difficult to use.
The brake booster will not work, so the brakes will not
grip well. The brake pedal will be harder to press than
usual.
Since there is no power steering assist, the steering wheel
will be hard to turn.When the engine fails at the intersection Get help from your passengers, bystanders, etc. to push the
vehicle and move it to a safe zone.
Jump-starting the engine
N00836400696
If the engine cannot be started because the battery is weak or
dead, you can start it with the battery from another vehicle
using jumper cables.
1. Take off any metal jewelry such as watch bands or brace-
lets that might make an accidental electrical contact.
2. Position the vehicles close enough together so that the
jumper cables can reach, but be sure the vehicles aren’t
touching each other.
WA R N I N G
!When using jumper cables to start a vehicle, follow
the procedures and be very cautious.
CAUTION
!Do not try to start your vehicle by pushing or tow-
ing. Vehicles with automatic transaxles cannot be
started this way. Pushing or towing a vehicle that
has a manual transaxle may overheat and damage
the catalytic converter. Also, there is more risk of an
accident when a vehicle is being pushed or towed.
CAUTION
!Check the other vehicle. It must have a 12-volt bat-
tery. If the other system isn’t 12-volt, both systems
can be damaged.
BK0139500US.book 2 ページ 2011年4月19日 火曜日 午後1時48分
Page 316 of 424
For emergencies
6-5
6
Low battery chargeIf you drive your vehicle with a low battery charge after the
engine has been started by using jumper cables, the engine may
misfire. This can cause the anti-lock braking system warning
light to blink on and off. This is only due to the low battery
voltage. It is not a problem with the brake system. If this hap-
pens, fully charge the battery and ensure the charging system is
operating properly.
Engine overheating
N00836500222
If the engine coolant temperature gauge indicator moves to the
“H” (hot) position (red zone), the engine may be overheated. If
this happens:
1. Stop the vehicle in a safe place. Turn on the hazard warn-
ing flashers.
2. With the engine still running, carefully raise the engine
hood to vent the engine compartment.
3. Check that the cooling fan is running. If the fan is not
turning, stop the engine immediately and contact an
authorized Mitsubishi Motors dealer or a repair facility of
your choice for assistance.
4. If you see steam or spray coming from under the hood,
turn off the engine.
WA R N I N G
!To avoid personal injury, keep hands, hair, jewelry
and clothes away from the cooling fan. The cooling
fan can start at any time.
BK0139500US.book 5 ページ 2011年4月19日 火曜日 午後1時48分
Page 320 of 424
For emergencies
6-9
6 How to change a tire
N00836900806
Before changing a tire, first stop your vehicle in a safe, flat
location.
1. Park the vehicle on level and stable ground.
2. Set the parking brake firmly, move the selector lever to
the “P” (PARK) position.
3. Turn on the hazard flashers and turn the ignition key to the
“LOCK” position.
4. Set up a warning triangle, flashing signal light, etc., at an
adequate distance from the vehicle, and have all your pas-
sengers leave the vehicle.5. To prevent the vehicle from rolling when it is raised on the
jack, place chocks or blocks (A) at the tire that is diago-
nally opposite from the tire (B) you are changing.
WA R N I N G
!Be sure to apply chocks or blocks to the correct tire
when jacking up the vehicle. If the vehicle moves
while jacked up, the jack could slip out of position,
leading to an accident.
BK0139500US.book 9 ページ 2011年4月19日 火曜日 午後1時48分
Page 375 of 424
7-40 Vehicle care and maintenance
7
*: Fusible link
Some fuses may not be installed on your vehicle, depend-
ing on the vehicle model or specifications.
The table above shows the main equipment corresponding
to each fuse.
4 Ignition switch 40 A*
5 Power window control 30 A*
6Front fog lights/
Daytime running lights15 A
7 Heated seat 20 A
8 Horn 15 A
9 Engine control 20 A
10 Air conditioning 10 A
11 Stop lights 15 A
12 Rear fog light 10 A
13 Alternator 7.5 A
14 Hazard warning flasher 10 A
15 Automatic transaxle 20 A
16 Headlight high beam (right) 10 A
17 Headlight high beam (left) 10 A
18 Headlight low beam (right) 10 A
19 Headlight low beam (left) 10 A
20 Tail light (right) 7.5 A
21 Tail light (left) 7.5 A
22 Dome light 10 A No.
Symbol
Electrical system
Capacity
23 Radio 10 A
24
Fuel pump 15 A
25 Windshield wiper 30 A No.
Symbol
Electrical system
Capacity
BK0139500US.book 40 ページ 2011年4月19日 火曜日 午後1時48分
Page 416 of 424
Alphabetical index
1
A
Accessory boxes 3-131
Accessory (installation) 1-7
Active stability control 3-51
ASC indicator 3-54
ASC OFF indicator 3-54
ASC OFF switch 3-53
Skid control function 3-53
Traction control function 3-52
Air cleaner filter 7-11
Air conditioning 5-5
,5-13
Important operating tips for the air conditioning 5-21
Air conditioning label 9-2
Aluminum wheels 7-66
Antenna
Glass antenna 5-71
Satellite radio antenna 5-71
Anti-lock braking system 3-49
Warning light 3-50
Arm rest 2-11
ASC 3-51
ASC indicator 3-54
ASC OFF indicator 3-54
ASC OFF switch 3-53
Audio system 5-22
AM/FM electronically tuned radio with CD autochanger-
Type 2 5-37AM/FM electronically tuned radio with CD player-Type 1
5-24
AM/FM/Satellite electronically tuned radio with CD au-
tochanger-Type 3 5-37
Handling of compact discs 5-68
Steering wheel remote control switch 5-62
Automatic transaxle 3-39
Fluid 7-12
,9-8
Selector lever operation 3-39
Selector lever positions 3-43
Sports mode 3-44
B
Back-up lights
Capacity 7-45
Replacement 7-54
Ball joint, steering linkage seals, drive shaft boots 7-32
Battery 7-15
Charging system warning light 3-80
Checking battery electrolyte level 7-16
Disconnection and connection 7-17
During cold weather 7-17
Specification 9-7
Brake
Anti-lock braking system 3-49
Braking 4-7
Fluid 7-14
,9-8
Hose 7-31
Parking brake 3-28
BK0139500US.book 1 ページ 2011年4月19日 火曜日 午後1時48分
Page 417 of 424
Alphabetical index
2Parking brake lever stroke 7-28
Pedal 3-47
Pedal free play 7-28
Power brakes 3-48
Service brake 3-47
Warning light 3-78
Break-in recommendations 3-2
Bulb capacity 7-45
C
California Perchlorate Materials Requirements 1-9
Capacities 9-8
Cargo loads 4-13
Catalytic converter 7-3
Certification label 9-4
Charging system warning light 3-80
Child restraints 2-27
Child safety locks for rear door 3-15
Cleaning
Inside of your vehicle 7-62
Outside of your vehicle 7-63
Clock 3-123
Coat hooks 3-134
Combination headlights and dimmer switch 3-81
Consumer information 8-2
Coolant (engine) 7-9
,9-8
Cruise control 3-57
Indicator light 3-58
Cup holder 3-133
D
Defogger (rear window) 3-90
Digital clock 3-123
Dimensions 9-4
Dimmer (high/low beam change) 3-83
Disc brake pads 7-31
Dome light 3-129
Capacity 7-46
Replacement 7-59
Door-ajar warning buzzer 3-80
Door-ajar warning light 3-80
Doors
Lock 3-12
Power door locks 3-14
Drive belt 7-32
Driving during cold weather 4-6
Driving, alcohol and drugs 4-2
E
Electric rear window defogger switch 3-90
Electronic immobilizer (Anti-theft starting system) 3-3
Emission-control system maintenance 7-29
Engine
Compartment 7-6
Coolant 7-9
,9-8
Coolant temperature gauge 3-76
Hood 7-4
Malfunction indicator light 3-79
BK0139500US.book 2 ページ 2011年4月19日 火曜日 午後1時48分