light MITSUBISHI iMiEV 2012 1.G Owners Manual

5-6 Comfort controls
5Air conditioning
N00730300328
The air conditioning can only be used when the ready indicator
is illuminated.NOTE
If the energy level gauge is at 0 bars or the power down
warning light illuminates, the vehicle interior may not be
cooled/heated even though the dial or switch is operated.
Furthermore, the defog performance may be also reduced.
Refer to “Energy level gauge” on page 3-69.
Refer to “Power down warning light” on page 3-75.
Control panel
N00730500290
A- Temperature control dial
B- MAX switch
C- Blower speed selection dial
D- Air conditioning switch
E- Mode selection dial
F- Air selection switch
BK0140800US.book 6 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Comfort controls
5-9
5
“AUTO” position
The vents change to the following positions according to the
position of the temperature control dial.
Refer to “Temperature control dial” on page 5-8.
Air selection switch
N00736800400
Normally, use the outside air position to keep the windshield
and side windows clear and to quickly remove fog or frost
from the windshield.
To change the air selection, simply press the air selection
switch.

Outside air {Indicator light (A) OFF}
Outside air is introduced into the passenger compartment.

Recirculated air {Indicator light (A) ON}
Air is recirculated inside the passenger compartment.
Temperature control dial position
Ve n t s
Between “C” and middle(
): Upper part of front
passenger compartment
Middle(
)Set the dial to middle
(
) from the “C” side: Upper part of front
passenger compartment
Set the dial to middle
(
) from the “H” side: Leg area
Between
middle (
)
and “H”Near middle (
)
: Leg area
Near “H”: Leg area,
windshield, and door
windowsCAUTION
!
When using the mode selection dial between the
“ ” and “ ” positions, prevent fogging by press-
ing the air selection switch to select outside air.
(Refer to “Air selection switch” on page 5-9.)
BK0140800US.book 9 ページ ２０１１年９月２９日　木曜日　午後３時２８分

5-10 Comfort controls
5
If high cooling performance is desired, or, if the outside air is
dusty or contaminated in some way, use the recirculation posi-
tion. Switch to the outside air position every now and then to
keep the windows from fogging up. NOTE
When the mode selection dial is set to the “ ” position,
the air conditioning compressor runs automatically. Out-
side air introduction will also be selected automatically.

When the temperature control dial is set to the “C” posi-
tion, the air selection will be automatically set to the
recirculation position.
Air conditioning switch
N00731000465
Push the switch, and the air conditioning compressor will turn
on. The air conditioning indicator light (A) will come on.
Push the switch again and the air conditioning compressor will
stop and the indicator light (A) goes off.
CAUTION
!
Using recirculated air for a long time may cause the
windows to fog up.
BK0140800US.book 10 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Comfort controls
5-11
5
MAX switch
N00766500015
When the blower speed selection dial is not OFF and the MAX
switch is pressed, the indicator light (A) illuminates and cool-
ing/heating performance and the air conditioning setting is
changed according to the temperature control dial position.
When the switch is pressed again, the operation returns to the
mode before pressing the switch.
When the temperature control dial is set between middle
(
) and “H” position
The heating capability is at maximum.
When the temperature control dial is in middle (
) posi-
tion
The air flow is at maximum.When the temperature control dial is set between “C” and
middle (
) position
The air conditioning automatically operates and the cooling
capability is at maximum.
NOTE
Do not use the cooling/heating function with the MAX
switch for a long time. Because the power consumption is
greatly increased, the cruising range is shortened.

When the blower speed selection dial or temperature con-
trol dial is operated with the indicator light illuminated,
the indicator light goes out and the selected function over-
rides others.
Other functions return to the mode before pressing the
MAX switch.

When the air conditioning is operated with the MAX
switch, the air conditioning does not stop if the function is
cancelled.
BK0140800US.book 11 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Comfort controls
5-13
5
Quick heating1. Set the mode selection dial to the “ ” position.
2. Set the air selection switch (A) to the outside position.
3. Turn the temperature control dial clockwise or counter-
clockwise to between middle (
) position and “H” posi-
tion.
4. Turn the blower speed selection dial to any position other
than “OFF” position.
5. Press the MAX switch (B).NOTE
Do not use the heating function with the MAX switch for
a long time. Because the power consumption is greatly
increased, the cruising range is shortened.
Cooling
N00731200337
For ordinary cooling

1. Set the mode selection dial to the “ ” position.
2. Set the air selection switch (A) to the outside position.
3. Turn the temperature control dial clockwise or counter-
clockwise to the desired temperature between middle (
)
and “C” position.
4. Select the desired blower speed.
5. Push the air conditioning switch (B).
6. When the air conditioning is operating, the switch indica-
tor light (C) illuminates.
BK0140800US.book 13 ページ ２０１１年９月２９日　木曜日　午後３時２８分

5-14 Comfort controls
5
NOTE
If the outside air is dusty or contaminated in some way, set
the air selection switch (A) to the recirculation position.
Let in some outside air from time to time for good ventila-
tion.

To cool the leg areas, set the mode selection dial to the
“ ” position.NOTE
When the blower speed selection dial is set to the
“AUTO” position, the air flow is adjusted automatically
according to the temperature of the interior and the posi-
tion of the temperature control dial.For quick cooling

1. Set the mode selection dial to the “ ” position.
2. Set the air selection switch (A) to the recirculation posi-
tion.
3. Turn the temperature control dial clockwise or counter-
clockwise to between middle (
) and “C” position.
4. Turn the blower speed selection dial to any position other
than “OFF” position.
5. Press the MAX switch (B).
The air conditioning automatically operates and the indi-
cator light (C) illuminates.
NOTE
Do not use the cooling function with the MAX switch for
a long time. Because the power consumption is greatly
increased, the cruising range is shortened.
BK0140800US.book 14 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Comfort controls
5-17
5 Important air conditioning operating tips
N00733700323
1. Park the vehicle in the shade whenever possible. Parking
in the hot sun makes the vehicle interior extremely hot
which then requires more time to cool. If it is necessary to
park in the sun, open the windows for the first few min-
utes of air conditioning to expel the hot air.
2. Afterwards, keep the windows closed when the air condi-
tioning is in use. The entry of outside air through open
windows will reduce cooling efficiency.
3. When running the air conditioning, make sure the air
intake, which is located in front of the windshield, is free
of obstructions such as leaves. Leaves collected in the air-
intake chamber may reduce air flow and plug the water
drains. Air conditioning system refrigerant and lubri-
cant recommendations If the air conditioning seems less effective than usual, the cause
might be a refrigerant leak.
Have the system inspected by a certified i-MiEV dealer.
During a long period of disuse The air conditioning should be operated for at least five min-
utes each week, even in cold weather. This includes the quick
defrosting mode. Operating the air condition system weekly
maintains lubrication of the compressor internal parts and
maintains the air conditioning in the best operating condition.
CAUTION
!
The air conditioning system in your vehicle must be
charged with the refrigerant HFC-134a and the
lubricant POE MA68EV.
Use of any other refrigerant or lubricant will cause
severe damage and may require replacing your vehi-
cle’s entire air conditioning system.
The release of refrigerant into the atmosphere is not
recommended.
The new refrigerant HFC-134a in your vehicle is
designed not to harm the earth’s ozone layer. How-
ever, it may contribute slightly to global warming.
It is recommended that the old refrigerant be saved
and recycled for future use.
BK0140800US.book 17 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Comfort controls
5-39
5

In the following circumstances, moisture can form on
compact discs and inside the audio system, preventing
normal operation.
• When there is high humidity (for example, when it is
raining).
• When the temperature suddenly rises, such as right after
the heater is turned on in cold weather.
In this case, wait until the moisture has had time to dry
out.

When the CD player is subjected to violent vibrations,
such as during off-road driving, the tracking may not
work.

When storing compact discs, always store them in their
separate cases. Never place compact discs in direct sun-
light, or in any place where the temperature or humidity is
high.

Never touch the flat surface of the disc where there isn’t a
label. This will damage the disc surface and could affect
the sound quality. When handling a compact disc, always
hold it by the outer edge and the center hole.

To clean a disc, use a soft, clean, dry cloth. Wipe directly
from the center hole toward the outer edge. Do not wipe in
a circle. Never use any chemicals such as benzine, paint
thinner, a disc spray cleaner, or an anti-static agent on the
disc.

Do not use a ball point pen, felt pen, pencil, etc. to write
on the label surface of the disc.
Do not put additional labels or stickers on compact discs.
Also, do not use any compact disc on which a label or
sticker has started to peel off or any compact disc that has
stickiness or other contamination left by a peeled-off label
or sticker. If you use such a compact disc, the CD player
may stop working properly and you may not be able to
eject the compact disc.
BK0140800US.book 39 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Comfort controls
5-43
5
ReflectionThe reason why one can hear FM but not AM in parking
garages, under bridges etc., is that FM signals, unlike AM sig-
nals, are reflected by solid objects such as buildings, etc.
Because FM signals are easily reflected by buildings, this can
also cause reception disturbances.
The direct signal from the broadcast station reaches the antenna
slightly before the reflected signal. This time difference may
cause some reception disturbance or flutter.
This problem occurs primarily in urban areas.
Cross modulationIf one listens to a weak station and is in the vicinity of another
strong station, both stations might be received simultaneously.FM stereo receptionStereo reception requires a high quality broadcast signal. This
means that types of disturbances mentioned previously become
more marked and the reception range is somewhat diminished
during stereo reception.
BK0140800US.book 43 ページ ２０１１年９月２９日　木曜日　午後３時２８分

5-44 Comfort controls
5
Causes of disturbancesFM reception is affected by the electrical systems of vehicles in
the vicinity, especially those without an electronic noise sup-
pression device. The disturbance is even greater if the station is
weak or poorly tuned.
FM reception is not as sensitive to electrical disturbances as
AM. AM reception is sensitive to electrical disturbances such
as power lines, lightning and other types of similar electrical
phenomena.BK0140800US.book 44 ページ ２０１１年９月２９日　木曜日　午後３時２８分