lock MITSUBISHI iMiEV 2012 1.G Owners Manual

Vehicle care and maintenance
7-33
7
Identification of fuse
N00901100078
Fuse replacement
N00954900115
1. Before replacing a fuse, always turn off the electrical item
connected to the fuse and turn the electric motor switch to
the “LOCK” position.
2. Remove the fuse puller (A) from the inside of the fuse
cover in the passenger compartment.
Capacity
Color
7.5 A Brown
10 A Red
15 A Blue
20 A Yellow
30 A Green (fuse type) /Pink (fusible link type)
40 A Green (fusible link type)
BK0140800US.book 33 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-34 Vehicle care and maintenance
7
3. Clamp it on the fuse you wish to remove, and pull the fuse
straight out from the fuse block.4. Use the fuse location diagrams and their corresponding
tables, to check the fuse that is related to the problem. If
the fuse is not blown, something else must be causing the
problem.
Contact a certified i-MiEV dealer to have the problem
checked.
5. Insert a new fuse of the same capacity securely into the
appropriate slot.
B- Fuse is OK
C- Blown fuse
BK0140800US.book 34 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-38 Vehicle care and maintenance
7
Front side-marker lights
N00915500161
1. Insert a flat blade screwdriver into the end of the light
nearer the rear of the body and pry gently to remove the
light.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.2. Remove the socket and bulb assembly together by turning
it counterclockwise.*: Front of the vehicle
*
BK0140800US.book 38 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-40 Vehicle care and maintenance
7
Front turn signal lights/Front fog lights (if so
equipped)/Daytime running lights
(if so equipped)
N00943400312
1. To create enough work space, turn the steering wheel all
the way in the same direction to the side you wish to
replace.
2. Remove the clip (A) and bolts (B), then lift the cover (C).3. Turn the socket counterclockwise to remove it.
D- Front turn signal light
E- Front fog light
F- Daytime running light
BK0140800US.book 40 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-43
7
4. Turn the socket counterclockwise to remove it.NOTE
The tail and stop lights use LEDs rather than bulbs.
For repair and replacement, contact a certified i-MiEV
dealer.5. Pull the bulb out of the socket.
6. To install the bulb, perform the removal steps in reverse.C- Tail and stop light (LED) - cannot be replaced
D- Rear turn signal light
E- Back up light
BK0140800US.book 43 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-44 Vehicle care and maintenance
7
Rear side-marker lights
N00935400108
1. Remove the clips (A), then lift the cover (B).2. Turn the socket (C) counterclockwise to remove it.
3. Pull the bulb out of the socket.
BK0140800US.book 44 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-50 Vehicle care and maintenance
7
These can all be dangerous, and they all can damage your vehi-
cle.
Cleaning the inside of your vehicle
N00945200079
After washing the inside of your vehicle with any cleaner, wipe
it dry in a shady, well ventilated area. NOTE
Always read the instructions on the cleaner label.Plastic, vinyl leather, fabric and flocked parts
N00945300214
1. Lightly wipe these off with a soft cloth soaked in a mild
soap and water solution.
2. Dip cloth in fresh water and wring out well. Using this
cloth, wipe off the detergent thoroughly.
CAUTION
!
Do not use organic substances (solvents, benzine,
kerosene, alcohol, gasoline, etc.) or alkaline or acidic
solutions.
These chemicals can cause discoloring, staining or
cracking of the surface.
If you use cleaners or polishing agents, make sure
their ingredients do not include the substances men-
tioned above.
BK0140800US.book 50 ページ ２０１１年９月２９日　木曜日　午後３時２８分

7-52 Vehicle care and maintenance
7Cleaning the outside of your vehicle
N00945700061
To protect your vehicle’s finish, wash it often and thoroughly.
If desired, you may wax your vehicle using a nonabrasive auto-
mobile wax. Foreign material
N00945800046
Industrial pollution, road tar, bird droppings, tree sap, insect
remains, sea water and other foreign matters can damage the
finish on your vehicle.
Generally, the longer any foreign material stays on the finish,
the worse the damage. Wash your vehicle as soon as possible
whenever the finish gets soiled.Wa s h i n g
N00945900627
Chemicals contained in the dirt and dust picked up from air,
rain, snow or road surfaces can damage the paint and body of
your vehicle if left on.
Frequent washing and waxing is the best way to protect your
vehicle from this damage.
Do not wash the vehicle in direct sunlight. Park the vehicle in
the shade and spray it with water to remove dust. Next, using
plenty of clean water and a car washing mitt or sponge, wash
the vehicle from top to bottom.
Use a mild car washing soap if necessary. Rinse thoroughly
and wipe dry with a chamois or soft cloth. After washing the
vehicle, carefully clean the joints and flanges of the doors,
hood, etc., where dirt is likely to remain.
WA R N I N G
!
Do not wash the vehicle while charging the main
drive lithium-ion battery.
Doing so could cause a fire or an electric shock.
Before washing the vehicle, make sure that the
charging lid and the inner lid are completely closed.
If the lid is open, the charging unit is exposed to
water, resulting in a fire or an electric shock.
Do not pour water inside the electric motor unit
room. Doing so could cause a fire or an electric
shock.
CAUTION
!
When washing the vehicle, turn the electric motor
switch to the “LOCK” position.
Do not use a high pressure washing machine to clean
the underneath of the vehicle.
Doing so might cause the electric motor unit prob-
lem or malfunction.
When washing the underside of your vehicle or the
wheels, wear a pair of gloves to protect your hands.
Never spray or splash water on the electrical parts
in under the hood. This may damage them. Be care-
ful also when washing the underbody. Do not spray
water up under the hood.
BK0140800US.book 52 ページ ２０１１年９月２９日　木曜日　午後３時２８分

9-4 Specifications
9
Electric motor numberThe electric motor number is stamped on the cylinder block as
shown in the illustration.
Tire and loading information placard
N01148100599
The tire and loading information placard is located on the
driver’s door sill.
*- Front of the vehicleBK0140800US.book 4 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Specifications
9-7
9 Charging system specifications
N01148500014
*: When using a genuine charging cable with control boxRegular charging system
Rated input voltage AC 240V (single phase) AC 120V (single phase)Rated input frequency 50 Hz/60 HzMaximum rated current 15 A 8 A*Maximum power consumption 3.3 kW 1.0 kW*Applicable standardsUL2594: Electric Vehicle Supply Equipment
UL62: Flexible Cords and Cable
UL2251: Plugs, Receptacles and Couplers for Electric Vehicle
SAE J1772: (R) SAE Electric Vehicle and Plug in Hybrid Electric
Vehicle Conductive Charge Coupler
CSA C22.2 No.107.1-01: General use power supplies
CSA C22.2 No.42-10: General use receptacles, attachment plugs,
and similar wiring devices
CSA C22.2 No.49-10: Flexible Cords and Cables
CSA C22.2 No.182.2-M1987: Industrial Locking Type, Special
Use Attachment Plugs, Receptacles and ConnectorsLeakage current sensitivity in
cable control box20 mA
Quick charging system
Applicable standards CHAdeMOMaximum input current 125 A
Common charging system
Enclosure typeCharge connector: Type 3s
Control box (CCID): Type 3
BK0140800US.book 7 ページ ２０１１年９月２９日　木曜日　午後３時２８分