lock MITSUBISHI iMiEV 2012 1.G Owners Manual

Comfort controls
5-41
5 Clock
(if so equipped)
N00755000124
The time is displayed when the electric motor switch is in the
“ON” or “ACC” position.To set the time1. Press and hold the clock button and the clock display
flashes.
2. Press the SEEK button to adjust the “hours” digit.
If you keep pressing the button, fast-forward begins.3. When the “hours” digit is adjusted, press the clock button
to flash the “minutes” digit.
Press the SEEK button to adjust the “minutes” digit.
If you keep pressing the button, fast-forward begins.
4. When the time is set, press the clock button to stop the
clock display from flashing.
NOTE
Reset the time after the 12V starter battery terminals are
disconnected and reconnected.

Seconds do not appear in the clock display, but after
adjusting the “minutes” setting, the clock begins to oper-
ate from 0 seconds.
A- Clock button
B- SEEK (clock adjustment up) button
C- SEEK (clock adjustment down) button
BK0140800US.book 41 ページ ２０１１年９月２９日　木曜日　午後３時２８分

5-42 Comfort controls
5General information about your radio
N00733900439
Your vehicle’s radio receives both AM and FM stations.
The quality of your reception is affected by distance, obstacles,
and signal interference.
This radio complies with Part 15 of Federal Communications
Commission (FCC) Rules (for vehicles sold in U.S.A.). Opera-
tion is subject to the following conditions:

The device may not cause harmful interference.

This device must accept any interference recieved, includ-
ing interference that may cause undesirable operation.
Signal transmissionFM signals do not follow the earth surface nor are they
reflected by the upper atmosphere. For this reason, FM broad-
casts cannot be received over long distances. AM signals fol-
low the earth’s surface and are reflected by the upper
atmosphere. For this reason, AM broadcasts can be received
over longer distances.Weak reception (fading)Because of the limited range of FM signals and the way FM
waves transmit, you may experience weak or fading FM recep-
tion. When the broadcast is blocked by mountains or similar
obstructions, reception can be disturbed.
CAUTION
!
Changes or modifications not expressly approved by
the party meeting the above conditions could void
the user’s authority to operate the equipment.
FM AM
25 to 40 mile radius
(25 to 40 miles)100 mile radius
(100 miles)
BK0140800US.book 42 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-3
6
2. Position the vehicles close enough together so that the
jumper cables can reach, but be sure the vehicles are not
touching each other.
3. Set the parking brake firmly on your vehicle and move the
selector lever into the “P” (PARK) position.
4. Set the parking brake firmly on the other vehicle. Put the
automatic transaxle in “P” (PARK) or the manual
transaxle in “N” (Neutral).
5. Turn the ignition switch (the electric motor switch) on
each vehicle to the “LOCK” position.NOTE
Turn off all lights, heater, and other electrical loads. This
will help avoid sparks.6. Remove the battery cover, and then make sure your 12V
starter battery electrolyte is at the proper level. (Refer to
“Checking 12V starter battery electrolyte level” on page
7-14.)
7. Connect one end of one jumper cable to the positive
(+) terminal of the discharged battery (A), and then con-
nect the other end to the positive (+) terminal of the
booster battery (B).
CAUTION
!
Check the other vehicle. It must have a 12V battery.
If the other system is not 12V, both systems can be
damaged.
WA R N I N G
!
If the electrolyte fluid is not visible, or looks frozen,
DO NOT ATTEMPT JUMP STARTING!!
The battery might split open or explode if the tem-
perature is below the freezing point or if it is not
filled to the proper level.
BK0140800US.book 3 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-5
6
10. Check if the ready indicator illuminates.
[When the ready indicator illuminates]
Stop the engine of the other vehicle, and disconnect the
cables in the reverse order and keep the electric motor
switch in the ON position to charge the 12V starter battery
for more than 30 minutes.
After the 12V starter battery is charged, continue the pro-
cess from step 15.
[When the ready indicator does not illuminate]
Both the 12V starter battery and the main drive lithium-
ion battery have gone flat at the same time.
Charge the 12V starter battery and the main drive lithium-
ion battery by following steps from steps 11 to 13.
11. Keep the jumper cables to each vehicle connected and
turn the electric motor switch of your vehicle to the
“LOCK” position.NOTE
The jumper cables need to be connected to the 12V starter
battery when you start charging the main drive lithium-ion
battery because the on board charger etc. operate utilizing
power from the 12V starter battery.
12. Charge the main drive lithium-ion battery by regular
charging. The 12V starter battery is automatically charged
while charging the main drive lithium-ion battery. (Refer
to “Regular charging” on page 1-20.)13. When the charging indicator on the instrument cluster is
illuminated, stop the engine of the other vehicle and dis-
connect the jumper cables in the reverse order.
NOTE
When the regular charge connector is connected to the
charge port, the charging indicator will blink. When
charging has started, the charging indicator will illumi-
nate.

The 12V starter battery will automatically charge while
the main drive lithium-ion battery is charging.
14. Charge the main drive lithium-ion battery for more than 1
hour.
15. Disconnect the charging cable.
(Refer to “Regular charging” on page 1-20.)
BK0140800US.book 5 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-7
6
As your vehicle has anti-lock brakesIf you drive your vehicle with a low battery charge, after the
electric motor unit has been started by using jumper cables, it
can cause the anti-lock braking system warning light to illumi-
nate. This is only due to the low battery voltage. It is not a
problem with the brake system. If this happens, fully charge the
12V starter battery and ensure the charging system is operating
properly.
Tire repair kit
N00836600366
This vehicle is equipped with a tire repair kit which can be
used to repair a minor puncture in tread area caused by a nail,
screw or similar object. A spare tire is not provided with this
vehicle.
WA R N I N G
!
The tire repair kit may not permanently seal a punc-
tured tire.
Using the tire repair kit may damage the wheel
and/or the tire inflation pressure sensor for the tire.
The vehicle must promptly be inspected and
repaired by a certified i-MiEV dealer after using the
tire repair kit.
Use only the Mitsubishi genuine tire repair kit. Seal-
ant in other repair kits may not sufficiently seal the
tire puncture.
BK0140800US.book 7 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-11
6
NOTE
Do not pull out an object, such as a nail or screw, that pen-
etrates the punctured tire.

Move the vehicle so that the tire valve is positioned away
from the point where the tire touches the ground. If the
valve is near the point where the tire touches the ground,
the sealant may not enter the tire easily.
1. Park the vehicle on a safe, flat and level place.
2. Set the parking brake firmly.
3. Move the selector lever to the “P” (PARK) position and
turn the electric motor switch to the “LOCK” position.
4. Turn on the hazard warning flashers and set up a warning
sign, such as a warning triangle or flashing signal lamp, at
an adequate distance from the vehicle, and have all your
passengers leave the vehicle.
5. Take out the tire sealant bottle and the compressor.6. Shake the tire sealant bottle well.
NOTE
In cold conditions (when the ambient temperature is 32 °F
{0 °C} or lower), thickening of the tire sealant can make
the tire sealant hard to squeeze out of the bottle. Warm the
bottle between your hands inside the vehicle.
CAUTION
!
If the vehicle body is contaminated by the tire seal-
ant, wipe the tire sealant off immediately with a wet
cloth.
Immediately wash clothes contaminated with tire
sealant.
BK0140800US.book 11 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-13
6
9. Remove the valve insert (J) by turning it counterclockwise
using the valve remover (I). Put the removed valve insert
in a clean place so it does not get dirty.NOTE
Turn the valve remover by hand. If you use a tool, the
valve remover could be damaged.10. Remove the plug (K) from the free end of the hose (L).
Press the hose onto the valve (H).
WA R N I N G
!
If there is any air left in the tire when you remove
the valve insert, the valve insert may fly out and
injure you. Make sure the tire contains no air before
removing the valve insert.
BK0140800US.book 13 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-21
6
If a wheel gets stuck in a ditch, do not try to tow the vehicle.
Please contact a certified i-MiEV dealer or a commercial tow
truck service for assistance.
There may be local regulations concerning towing in your area.
Obey the regulations in the area where you are driving your
vehicle.Towing the vehicle by a tow truckTowing with rear wheels off the ground
Place the selector lever in the “N” (NEUTRAL) position. Turn
the electric motor switch to the “ACC” position and secure the
steering wheel in a straight-ahead position with a rope or tie-
down strap. Never place the electric motor switch in the
“LOCK” or “ON” position when towing.
WA R N I N G
!
Never get under your vehicle after it has been lifted
by a tow truck.
Never ride in a vehicle that is being towed.
CAUTION
!
If the transmission or the steering system has a
problem or damage, transport the vehicle on a flat-
bed truck or tow the vehicle with the all wheels off
the ground.
If the electric motor switch is in the “ON” position,
the Active Stability Control (ASC) system may oper-
ate, resulting in an accident. Make sure the electric
motor switch is in the “ACC” position before tow-
ing.
BK0140800US.book 21 ページ ２０１１年９月２９日　木曜日　午後３時２８分

For emergencies
6-23
6
On snowy or icy roads
When driving on a road covered with snow or ice, use
snow tires. Tire chains cannot be used on your vehicle.
There may be state or local regulations about using snow
tires. Always check the regulations in your local area
before using them. Refer to the section entitled “Snow
tires” on page 7-24 and “Tire chains” on page 7-24.

Drive slowly. Do not make sudden starts or stops, sharp
turns, or slam on the brakes.

Allow extra distance between your vehicle and the vehicle
in front of you, and avoid sudden braking.

If a skid occurs when the accelerator pedal is depressed,
take your foot off the pedal. Steer gently in the direction
of the skid.

Your vehicle is equipped with an anti-lock braking system
(ABS), hold the brake pedal down firmly and keep it
depressed. Do not pump the brake pedal which will result
in reduced braking performance.

After parking on snowy or icy road, it may be difficult to
move your vehicle due to freeze-up of the brake. Depress
the accelerator pedal little by little to move the vehicle
after confirming safety of the vehicle.
On a bumpy or rutted road
Drive as slow as possible when driving on bumpy or rut-
ted roads or over potholes etc.
CAUTION
!
Do not depress the accelerator pedal rapidly. The
vehicle could start moving when it breaks free from
the ice, possibly resulting in an accident.
CAUTION
!
Driving on bumpy, rutted roads or over potholes can
damage the tires and wheels.
Wheels with low-profiles tires or under-inflated tires
are especially at risk for damage.
The vehicle’s body, bumper, muffler and other parts
may be damaged if the vehicle is:
• driven over a step (for example, at the entrance or
exit of a parking lot);
• parked too closely against a curb or parking block,
or by the side of a road with curbstones;
• driven on a steep slope.
BK0140800US.book 23 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Vehicle care and maintenance
7-3
7
Have you purchased the Mitsubishi Motors Diamond Care Pro-
tection Plan? The Plan supplements your new vehicle warran-
ties. See a certified i-MiEV dealer for details.
WA R N I N G
!
When servicing the vehicle, make sure that the elec-
tric motor switch is in the “LOCK” position and the
charging cable is disconnected. Failure to do so
could result in an electric shock.
When checking or servicing under the hood or the
coolant reserve tank, be sure the electric motor unit
is stopped and it has had a chance to cool down.
If you need to work under the hood with the electric
motor unit on, be careful that your clothing, hair,
etc. does not get caught in the fan or other moving
parts.
The fan can turn on automatically even if the elec-
tric motor unit is not running. Turn the electric
motor switch to the “LOCK” position to be safe
while you are working under the hood.
Do not smoke or allow open flames around the 12V
starter battery.
Be extremely careful when working around the 12V
starter battery. It contains poisonous and corrosive
sulfuric acid.
Handling your vehicle’s parts and materials in the
wrong way can injure you. Ask a certified i-MiEV
dealer if you have questions.
CAUTION
!
The components inside the electric motor unit room
may be very hot to the touch.
Make sure all components have sufficiently cooled
before beginning an inspection.
These components are affixed with a label indicating
precautions for handling. Follow the instructions on
the label.
When replacing the 12V starter battery, remove the
positive (+) and negative (-) terminals after turning
the electric motor switch to the “LOCK” position
and waiting at least 2 minutes. If the 12V starter
battery terminal is removed just after the electric
motor switch is turned to the “LOCK” position, this
may cause damage to electric components.
If the electric motor unit warning light illuminates,
do not replace the 12V starter battery. Contact a
certified i-MiEV dealer.
BK0140800US.book 3 ページ ２０１１年９月２９日　木曜日　午後３時２８分