lock MITSUBISHI iMiEV 2012 1.G Service Manual

3-2 Features and controls
3Break-in recommendations
N00508700343
Advanced automobile manufacturing techniques permit you to
operate your new vehicle without requiring a long break-in
period of low-speed driving.
However, you can add to the future performance and economy
of your vehicle by observing the following precautions during
the first 300 miles (500 km).
Drive your vehicle at moderate speeds during the break-in
period.

Do not overload the vehicle. Observe the seating capacity
(See “Cargo load precautions” on page 4-13).

Do not use this vehicle for trailer towing.
Keys
N00508800618
Two keys are provided.
The keys fit all locks. Keep one in a safe place as a spare key.
BK0140800US.book 2 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-4 Features and controls
3
NOTE
In the following cases, the vehicle may not be able to rec-
ognize the registered ID code from the key. This means
the electric motor unit will not start even when the
registered key is turned to the “START” position.
• When the key contacts a key ring or other metallic or
magnetic object (Type A)
• When the key grip contacts metal of another key
(Type B)
• When the key contacts or is close to other immobilizing
keys (including keys of other vehicles) (Type C)

In cases like the above, move the offending object(s) away
from the key and turn the key back to the “ACC” or
“LOCK” position. Then try to start the electric motor unit
again. If the electric motor unit does not start, contact a
certified i-MiEV dealer.
BK0140800US.book 4 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-5
3
NOTE
Electronic immobilizer is not compatible with commer-
cially available remote starting systems. Use of commer-
cially available remote starting systems may result in
vehicle starting problems and a loss of security protection.

A system failure is suspected when the electric motor
switch is turned to the “START” position, and the electric
motor unit does not start. In such a case, contact a certified
i-MiEV dealer.Replacement keysOnly keys that have been programmed to the vehicle electron-
ics can be used to start the vehicle.
If you lose a key, you can order a key from a certified i-MiEV
dealer by referring to the key number.
To prevent vehicle theft, the ID code for the vehicle keys must
be changed.
Take your vehicle and all remaining keys to a certified i-MiEV
dealer to have your ID code changed.
Additional keysTo add a key, you need to register the ID code to the vehicle.
Registering the ID code can be done by a certified i-MiEV
dealer. Or it can be done by yourself (except for vehicles sold
in Canada).
To register the ID code yourself, follow the “Customer key
programming” procedure below.
If you choose to have a certified i-MiEV dealer register the ID
code, take your vehicle and any remaining keys to a certified i-
MiEV dealer.NOTE
You are provided with 2 keys, but you may add up to 6
more keys.Customer key programming (Except for vehicles
sold in Canada)
N00562200113
You can program new keys to the system if you have two valid
(already registered) keys and blank (not registered) immobi-
lizer key (specially cut for your vehicle at a certified i-MiEV
dealer) by doing the following:
1. Insert the first valid key into the ignition and turn the igni-
tion to the “ON” position for 5 seconds.
2. Turn the ignition to the “LOCK” position and remove the
first key.
3. Within 30 seconds of turning the first key to the “LOCK”
position, insert the second valid key into the ignition and
turn it to the “ON” position. About 10 seconds later, the
immobilizer indicator will start blinking.
CAUTION
!
Do not make any alterations or additions to the
immobilizer system. Alterations or additions could
cause failure of the immobilizer.
BK0140800US.book 5 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-6 Features and controls
3
4. When the immobilizer indicator starts blinking, turn the
second valid key to the “LOCK” position and remove it.
Within 30 seconds after doing so, insert a blank immobi-
lizer key into the ignition and turn it to the “ON” position.
Perform this operation no more than 30 seconds after the
immobilizer indicator starts blinking. When registration
of the ID code is complete, the immobilizer indicator will
come on for 3 seconds then go off. If an error occurs, the
immobilizer indicator will go off during the procedure.
5. If you wish to register another key, perform the process
again from step 1.
NOTE
It is not possible to register a key if:
• the immobilizer indicator goes off during the procedure
• the immobilizer indicator does not come on for 3 sec-
onds after turning the ignition to the “ON” position with
a blank immobilizer key

The procedure will be terminated automatically if:
• a period of 30 seconds or longer elapses from the
moment when the first key is turned to the “LOCK”
position to the moment when the second key is turned to
the “ON” position
• a period of 30 seconds or longer elapses from the
moment when the second key is turned to the “LOCK”
position to the moment when the blank immobilizer key
(specially cut for your vehicle at a certified i-MiEV
dealer) is turned to the “ON” position
• more than 20 seconds elapse after the immobilizer indi-
cator starts blinking
BK0140800US.book 6 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-7
3
General information
N00562300084
Your electronic immobilizer operates on a radio frequency sub-
ject to Federal Communications Commission (FCC) Rules
(For vehicles sold in U.S.A.) and Industry Canada Rules (For
vehicles sold in Canada). This device complies with Part 15 of
the FCC Rules and RSS-Gen of the Industry Canada Rules.
Operation is subject to the following two conditions.

This device may not cause harmful interference.

This device must accept any interference received, includ-
ing interference that may cause undesired operation.
This digital apparatus does not exceed the Class A limits for
radio noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian Department of
Communications.
Keyless entry system
N00509000907
Press the remote control transmitter buttons to lock or unlock
the doors and to open the liftgate.
It can also help you signal for attention by setting off the panic
alarm.
CAUTION
!
Changes or modifications not expressly approved by
the manufacturer for compliance could void the
user’s authority to operate the equipment.
1-
LOCK ( ) button
2-
UNLOCK ( ) button
3- PANIC button
4- Indicator light
BK0140800US.book 7 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-8 Features and controls
3
To l o c k Press the LOCK button (1) to lock all the doors and the liftgate.
If the dome light switch is in the door position, the dome light
will blink once. The turn signal lights will also blink once. NOTE
If you press the LOCK button (1) after locking the doors
and the liftgate, the horn will sound once to confirm that
they are locked.To unlock Press the UNLOCK button (2) to unlock the driver’s door only.
Within about 2 seconds, press the UNLOCK button one more
time to unlock all the doors and the liftgate.
If the dome light switch is in the door position, the dome light
will turn on for about 30 seconds. The turn signal lights will
also blink twice.NOTE
If the UNLOCK button (2) is pressed and no door or
liftgate is opened within about 30 seconds, relocking will
automatically occur.

The door and liftgate unlock function can be set so that all
doors and liftgate unlock when the UNLOCK button (2) is
pressed once.
For details, please contact a certified i-MiEV dealer.Answerback function The keyless entry system answerback functions from the horn
can each be turned on or off as desired.
Horn deactivation/reactivationThe horn answerback function can be set to the following three
conditions.
Each time the horn answerback function is set, a chime will
sound to tell you the condition of the answerback function.
1. Remove the key from the electric motor switch.
2. Open the driver’s door and turn the combination head-
lights and dimmer switch to the “OFF” position.
3. Press the LOCK button (1) for 4 to 10 seconds and press
the UNLOCK button (2) during this time.
4. Release in sequence the UNLOCK and LOCK buttons
within 10 seconds of pressing the UNLOCK button in step
3.Changing the setting of the turn signal lights answer-
back functionThe turn signal lights answerback function can be changed.
If you want to change the answerback function, please contact
a certified i-MiEV dealer for details.Number of
chimes
Condition
One chime The horn will not sound.
Two chimes The horn will sound.
Three chimesThe horn will sound if the auto light switch is
ON (if so equipped).
Four chimesThe horn will sound if the LOCK button is
pressed twice quickly.
BK0140800US.book 8 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-9
3
Setting of door unlock function
N00543600105
The door and liftgate unlock function can be set so that all
doors and liftgate unlock when the UNLOCK button (2) is
pressed once.
For details, please contact a certified i-MiEV dealer.Using the panic alarm
N00543700050
If you are near your vehicle and feel threatened, you may acti-
vate the alarm to call attention as follows:
1. Press the PANIC button (3) for more than 1 second.
2. The headlights will blink on and off and the horn will
sound intermittently for about 3 minutes.
3. To turn off the alarm, press any button on the remote con-
trol transmitter.
Replacement remote control transmitters
N00543800077
Only remote control transmitters programmed with the vehi-
cle’s electronics can lock or unlock all doors.
If you lose the remote control transmitter, you can order a
remote control transmitter from a certified i-MiEV dealer by
referring to the key number.
To prevent vehicle theft, the ID codes for all the remote control
transmitters except the one for the lost key must be pro-
grammed again.
Take your vehicle and all the remaining remote control trans-
mitters to a certified i-MiEV dealer to have your ID codes pro-
grammed again.
BK0140800US.book 9 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-12 Features and controls
3Door locks
N00509200534
To lock or unlock the door with the keyTurn the key toward the front of the vehicle to lock the door.
After checking that the door is locked, turn the key back to the
center and remove it.
WA R N I N G
!
Make sure all doors are tightly closed and locked
while driving.
• Locked doors, in combination with the use of seat
belts, can help reduce the risk of ejection in an
accident.
• Locked doors can help keep passengers, especially
small children, from opening doors and falling out
of moving vehicles.
• Locked doors can help prevent outsiders from
gaining access to your vehicle when you slow down
or come to a stop.

Lock your vehicle whenever you leave it. Children
who get into unlocked vehicles may not be able to
get out. Children trapped inside vehicles can quickly
be overcome by heat and suffer serious injury or
death due to heat stroke.
Never leave children unattended inside a vehicle. In
addition to the risk of heat stroke, children can acti-
vate switches and controls, resulting in an injury or
fatal accident.
1- Insert or remove the key
2- Lock
3- Unlock
BK0140800US.book 12 ページ ２０１１年９月２９日　木曜日　午後３時２８分

Features and controls
3-13
3
To lock or unlock the door from the inside Move the lock knob to the lock position to lock the door.
All doors should be kept locked while driving.
The driver’s door can be unlocked without using the lock knob
by pulling on the inside door handle.
To lock the door without using the key 1. Move the inside lock knob to the locked position.
2. Be sure the keys are not inside the vehicle. Close the door. Key reminder buzzer
N00549600240
If you open the driver’s door while the key is in the “LOCK” or
“ACC” position, a tone will sound, reminding you to remove
the key. Lock out protection
N00549700179
If the key is in the electric motor switch when you push the
lock knob forward with the driver’s door or passenger’s door
open, the lock knob will automatically return to the unlocked
position.
1- Lock
2- Unlock
BK0140800US.book 13 ページ ２０１１年９月２９日　木曜日　午後３時２８分

3-14 Features and controls
3Power door locks
N00509300607
NOTE
When locking or unlocking with the key on the driver’s
door, only the driver’s door will lock or unlock.

Repeated continuous operation between lock and unlock
could activate the power door locking systems built-in
protection circuit and prevent the system’s from operat-
ing. If this occurs, wait about 1 minute before operating
the power door lock switch.
To lock and unlock by the power door lock switchAll of the doors and the liftgate can be locked or unlocked by
operating the power door lock switch on the driver’s or the pas-
senger’s door. 1- Lock
2- Unlock
BK0140800US.book 14 ページ ２０１１年９月２９日　木曜日　午後３時２８分