lock MITSUBISHI iMiEV 2012 1.G Repair Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2012, Model line: iMiEV, Model: MITSUBISHI iMiEV 2012 1.GPages: 442, PDF Size: 12.6 MB
Page 181 of 442
3-32 Features and controls
3Steering wheel lock
N00512500209
To l o c kRemove the key at the “LOCK” position.
Turn the steering wheel until it is locked.To unlockTurn the key to the “ACC” position while moving the steering
wheel slightly.
NOTEIf the front wheels are turned, the anti-theft lock may
sometimes make it difficult to turn the key from “LOCK”
position to “ACC” position. Firmly turn the steering
wheel to the left or to the right as you turn the key.
CAUTION
!Remove the key when leaving the vehicle.If your vehicle needs to be towed, turn the key to the
“ACC” position to unlock the steering wheel.
BK0140800US.book 32 ページ ２０１１年９月２９日 木曜日 午後３時２８分
Page 183 of 442
3-34 Features and controls
3
NOTETo avoid erroneous operation, move the selector lever
firmly into each position and briefly hold it there. Always
check the position shown by the selector lever position
display after moving the selector lever.
If the brake pedal is not depressed and held, the shift-lock
device activates to prevent the selector lever from being
moved from the “P” (PARK) position.
Selector lever position indicator
N00513900431
When the electric motor switch is turned to the “ON” position,
the current position of the selector lever is indicated on the
instrument cluster.
WA R N I N G
!Always depress the brake pedal when shifting the
selector lever into another position from the “P”
(PARK) or “N” (NEUTRAL) position.
Never put your foot on the accelerator pedal while
shifting the selector lever from the “P” (PARK) or
“N” (NEUTRAL) position.
BK0140800US.book 34 ページ ２０１１年９月２９日 木曜日 午後３時２８分
Page 184 of 442
Features and controls
3-35
3
When the selector lever position indicator flashes while you are
driving, there could be a malfunction in the transmission.
Selector lever positions
N00514200369
“P” PARKThis position locks the transmission to prevent the vehicle
from moving. The electric motor unit can be started from the
“PARK” position.“R” REVERSEThis position is to back up.
CAUTION
!If the selector lever position indicator blinks while
you are driving, it is likely that a safety device is
operating because of a malfunction in the transmis-
sion system. We recommend you to have your vehi-
cle inspected as soon as possible.The selector lever position indicator warning func-
tion does not operate with the selector lever in the
“R” (REVERSE) position.
WA R N I N G
!Do not leave the vehicle with the electric motor
switch in the “ON” position. The vehicle can move
suddenly. To be sure the vehicle will not move, even
when you are on level ground, always set the park-
ing brake and move the selector lever to the “P”
(PARK) position.
CAUTION
!Never move the selector lever to the “P” (PARK) or
“R” (REVERSE) position while the vehicle is in
motion. If the lever is moved to the “P” (PARK) or
“R” (REVERSE) position while the vehicle is in
motion, the transmission could be damaged.
BK0140800US.book 35 ページ ２０１１年９月２９日 木曜日 午後３時２８分
Page 187 of 442
3-38 Features and controls
3Acoustic vehicle alerting system (AVAS)
N00571900028
While driving at low speeds, such as in parking lots, the acous-
tic vehicle alerting system (AVAS) alerts people who may not
hear your vehicle approaching.
The system sounds when the vehicle speed is approximately 22
mph (35 km/h) or less.
The acoustic vehicle alerting system (AVAS) will operate
under the following conditions:
When the vehicle speed is approximately 2 mph (3 km/h)
or less and the brake pedal is not depressed.
When the vehicle speed is approximately 2-22 mph (3-35
km/h).
The system will not operate under the following conditions:
When the vehicle speed is approximately 2 mph (3 km/h)
or less and the brake pedal is depressed.
When the vehicle speed is approximately 22 mph (35
km/h) or more.
When the selector lever is in the “P” (PARK) position.Under normal conditions, the indicator light in the instrument
cluster illuminates when the electric motor switch is turned to
the “ON” position and goes off a few seconds later. Always
confirm the indicator light goes off before driving.
NOTEIf the indicator light blinks, turn the electric motor switch
back to the “LOCK” position and again turn the switch to
the “ON” position.
It is not a malfunction if the indicator light goes off. If the
indicator light blinks again, however, have the vehicle
inspected at a certified i-MiEV dealer as soon as possible.
WA R N I N G
!Always pay special attention to pedestrians. Even if
the acoustic vehicle alerting system (AVAS) sounds,
pedestrians may not notice your vehicle.
BK0140800US.book 38 ページ ２０１１年９月２９日 木曜日 午後３時２８分
Page 190 of 442
Features and controls
3-41
3
NOTEOnce the brake assist system is operational, it maintains
great braking force even if the brake pedal is lightly
released.
To stop its operation, completely remove your foot from
the brake pedal.
The brake assist system may become operational when the
brake pedal is fully depressed even if it has not been
depressed suddenly.
When the brake assist system is in use while driving, you
may feel as if the depressed brake pedal is soft, the pedal
moves in small motions in conjunction with the operation
noise, or the vehicle body and the steering wheel vibrate.
This occurs when the brake assist system is operating nor-
mally and does not indicate faulty operation. Continue to
depress the brake pedal.
You may hear an operation noise when the brake pedal is
depressed suddenly while stationary. This does not indi-
cate a malfunction and the brake assist system is operating
normally.
Anti-lock braking system
N00517900325
The anti-lock braking system helps prevent the wheels from
locking up when braking. This helps you keep control of your
vehicle and its direction. Driving hints When using the anti-lock brakes (sudden braking), steer-
ing is slightly different from normal driving conditions.
Use the steering wheel carefully.
Always keep a safe distance from the vehicle in front of
you. Even if your vehicle is equipped with the anti-lock
braking system, leave a greater braking distance when:
• Driving on gravel or snow-covered roads.
• Driving on uneven road surfaces.
Operation of anti-lock braking system is not restricted to
situations where brakes are applied suddenly. This system
may also prevent the wheels from locking when you drive
over manholes, steel roadwork plates, road markings, or
any uneven road surface.
When the anti-lock braking system is in use, you may feel
the brake pedal vibrating and hear a unique sound. You
may also feel as if the pedal resists being pressed.
In this situation, simply hold the brake pedal down
firmly. Do not pump the brake, which will result in
reduced braking performance.
BK0140800US.book 41 ページ ２０１１年９月２９日 木曜日 午後３時２８分
Page 191 of 442
3-42 Features and controls
3
An operation noise may be emitted from under the hood in
the following situations. The sound is associated with
checking the operations of the anti-lock braking system.
At this time, you may feel a shock from the brake pedal if
you depress it. These do not indicate a malfunction.
• When the electric motor switch is set to the “ON” posi-
tion.
• When the vehicle is driven for a while after the electric
motor is turned on.
The ABS can be used after the vehicle has reached a speed
over approximately 6 mph (10 km/h). It stops working
when the vehicle slows below approximately 3 mph (5
km/h).
Anti-lock braking system warning light
N00531600661
This light comes on in the event of a malfunction in the anti-
lock braking system. It will also come on as a self-check for a
few seconds when the electric motor switch is turned to the
“ON” position. Always make sure that the light goes out before
beginning to drive.
CAUTION
!The anti-lock braking system cannot prevent acci-
dents. It is your responsibility to take safety precau-
tions and to drive carefully. Be sure to use the specified type and size of tire on
all four wheels. Otherwise, the ABS may not work
properly.Do not install any aftermarket limited slip differen-
tial (LSD) on your vehicle. The ABS may stop func-
tioning properly.
CAUTION
!If the anti-lock braking system warning light comes
on and stays on after starting the electric motor unit
or while driving, it means that the anti-lock braking
system is not working and that only the standard
brake system is available. (The standard brake sys-
tem will still work properly.) If this happens, take
your vehicle to a certified i-MiEV dealer as soon as
possible.
BK0140800US.book 42 ページ ２０１１年９月２９日 木曜日 午後３時２８分
Page 192 of 442
Features and controls
3-43
3
If the warning light illuminates while driving
N00531700590
If only the ABS warning light illuminateAvoid hard braking and high-speed driving. Stop the vehicle in
a safe place, put the selector lever to the “P” (PARK) position
and turn off the electric motor unit.
Restart the electric motor unit and check to see whether the
light goes out after a few minutes driving; if it then remains off
during driving, there is no problem.
However, if the warning light does not disappear, or if it comes
on again when the vehicle is driven, we recommend you to
have the vehicle checked.If the ABS warning light and brake warning light illu-
minate at the same timeThe ABS and brake force distribution function may not work,
so hard braking could make the vehicle unstable.
Avoid hard braking and high-speed driving. Stop the vehicle in
a safe place and we recommend you to have the vehicle
checked.NOTEThe warning light may be illuminated when the electric
motor unit is started while the 12V starter battery voltage
is low, but this is not an ABS malfunction.
When the main drive lithium-ion battery is charged, the
12V starter battery is charged at the same time, and the
warning light will go out.
If the warning light does not go out or illuminates from
time to time even after the battery is charged, take your
vehicle to a certified i-MiEV dealer and have the system
checked as soon as possible.After driving on snow or icy roads, remove any snow and
ice which may have been left around the wheels. On vehi-
cles that have an anti-lock braking system, be careful not
to damage the wheel speed sensors (A) or the cables
located at each wheel.
Front
BK0140800US.book 43 ページ ２０１１年９月２９日 木曜日 午後３時２８分
Page 193 of 442
3-44 Features and controls
3Electric power steering system (EPS)
N00568400045
The electric power steering system (EPS) operates while the
electric motor unit is running.
The EPS uses an electric motor to assist the turning of the
steering wheel.
The EPS has mechanical steering capability in case the power
assist is lost. If the power assist is lost for some reason, you
will still be able to steer your vehicle. If the power assist is lost,
you will notice it takes much more effort to steer and that there
is much more “free play” in the steering wheel. If this happens,
take your vehicle to a certified i-MiEV dealer.NOTEDuring repeated full-lock turning of the steering wheel
(for example, while you are maneuvering the vehicle into
a parking space), a protection function may be activated to
prevent overheating of the power steering system. This
function will make the steering wheel gradually harder to
turn. In this event, limit your turning of the steering wheel
for a while. When the system has cooled down, the steer-
ing effort will return to normal.
Rear
WA R N I N G
!Do not turn the key from the ON position while the
vehicle is moving. Stopping the electric motor unit
would make the steering wheel extremely hard to
turn, possibly resulting in an accident.
BK0140800US.book 44 ページ ２０１１年９月２９日 木曜日 午後３時２８分
Page 195 of 442
3-46 Features and controls
3Active stability control (ASC)
N00559100163
The active stability control (ASC) takes overall control of the
anti-lock braking system, traction control function and skid
control function to help maintain the vehicle’s control. Also
refer to the following pages on the anti-lock braking system,
traction control function and skid control function.
Anti-lock braking system (ABS) → P. 3 - 4 1
Traction control function → P. 3 - 4 6
Skid control function → P. 3 - 4 7
NOTEAn operation noise may be emitted from under the hood in
the following situations. The sound is associated with
checking the operations of the ASC. At this time, you may
feel a shock from the brake pedal if you depress it. These
do not indicate a malfunction.
• When the electric motor switch is set to the “ON” posi-
tion.
• When the vehicle is driven for a while after the electric
motor unit is turned on.
When the ASC is activated, you may feel a vibration in
the vehicle body or hear a whining sound from under the
hood.
This indicates that the system is operating normally. It
does not indicate a malfunction.
When the anti-lock braking system warning light is illu-
minated, the ASC is not active.Traction control function
N00559200050
On slippery surfaces, the traction control function prevents the
drive wheels from spinning excessively, thus helping the vehi-
cle to start moving from a stopped condition. It also provides
sufficient driving force and steering performance as the vehicle
turns while pressing the acceleration pedal.
CAUTION
!Do not over-rely on the ASC. Even the ASC cannot
prevent the natural laws of physics from acting on
the vehicle. This system, like any other system, has
limits and cannot help you to maintain traction and
control of the vehicle in all circumstances. Reckless
driving can lead to accidents. It is the driver’s
responsibility to drive carefully. This means taking
into account the traffic, road and environmental
conditions.Be sure to use the specified type and size of tire on
all four wheels. Otherwise, the ASC may not work
properly.Do not install any aftermarket limited slip differen-
tial (LSD) on your vehicle. The ASC may stop func-
tioning properly.
CAUTION
!When driving a vehicle on a snowy or icy road, be
sure to install snow tires and drive the vehicle at
moderate speeds.
BK0140800US.book 46 ページ ２０１１年９月２９日 木曜日 午後３時２８分
Page 211 of 442
3-62 Features and controls
3
NOTEThe cruising range indicator and outside temperature dis-
play are indicated when the electric motor switch is in the
“ON” position.
If there is no operation for about 10 seconds when the
meter illumination control or service reminder is shown,
the display returns to the odometer.Odometer
N00572300016
The odometer indicates the total distance the vehicle has trav-
eled.NOTEEven if the electric motor switch is turned to “ACC” or
“LOCK”, the odometer will be displayed for about 30 sec-
onds after the reset button is pressed.
1- Odometer
2-
Trip odometer
3-
Trip odometer
4- Dash lights brightness indicator
5- Service reminder (Drive distance remaining until next
inspection)
6- Service reminder (Number of months remaining until next
inspection)
7- Cruising range indicator
8- Outside temperature display
BK0140800US.book 62 ページ ２０１１年９月２９日 木曜日 午後３時２８分