oil type MITSUBISHI L200 2017 (in English) User Guide
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2017, Model line: L200, Model: MITSUBISHI L200 2017Pages: 426, PDF Size: 14.12 MB
Page 368 of 426
No.Sym-bolElectrical sys- temCa-
paci- tiesF11Headlamp wash- er20 AF12Stop lamps
(Brake lamps)15 AF13Ignition coil10 AF14Engine control7.5 AF15Alternator7.5 AF16Hazard warning flasher15 AF17Automatic trans-mission20 AF18Air conditioning20 A
F19
ETV15 AFuel line heater20 AF20Starter7.5 AF21———F22Fuel pump15 AF23Engine20 A*: Fusible link
No.Sym-
bolElectrical sys- temCa-
paci- tiesF24———#1—Spare fuse20 A#2—Spare fuse30 A* : Fusible link
l Some fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
l The table above shows the main equip-
ment corresponding to each fuse.
The fuse block does not contain spare 7.5 A ,
10 A or 15 A fuses. If one of these fuses burns out, substitute with the following fuse.7.5 A: Outside rear-view mirrors
10 A: Option
15 A: Cigarette lighter
When using a substitute fuse, replace with a
fuse of the correct capacity as soon as possi-
ble.
Identification of fuse
E01008100366
Ca-
pacityColour7.5 ABrownCa-
pacityColour10 ARed15 ABlue20 AYellow30 AGreen (fuse type) / Pink (fusible link type)40 AGreen (fusible link type)Fuse replacement
E01007801943
1.Before replacing a fuse, always turn off
the electrical circuit concerned and place
the ignition switch in the “LOCK” posi-
tion or put the operation mode in OFF.
2. Remove the fuse puller (A) from the in-
side of the fuse box in the engine com- partment.
Fuses
10-20OKTE17E1Maintenance10
Page 370 of 426
CAUTIONlNever hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., and
refit it after drying it thoroughly.
l Do not install commercially available LED-
type bulbs.
Commercially available LED-type bulbs
could adversely affect the operation of the vehicle, such as by preventing the lamps and
other vehicle equipment from operating properly.
NOTEl If you are unsure of how to carry out the
work as required, we recommend you to consult a specialist.
l Be careful not to scratch the vehicle body
when removing a lamp and lens.NOTEl When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon as when window glass mists up on a humid
day, and does not indicate a functional prob- lem. When the lamp is switched on, the heat
will remove the fog. However, if water gath- ers inside the lamp, we recommend you tohave the lamp checked.Bulb location and capacity
E01003201415
When replacing a bulb, use a new bulb with
the same wattage and colour.
OutsideE01003304967
Front
Except for vehicles with high intensity dis-charge headlamps
1. Position lamps: 5 W (W5W)
2. Front turn-signal lamps: 21 W (PY21W/
P21W)
3. Headlamps, high/low beam: 60/55 W
(H4)
4. Type 1 Front fog lamps: 35 W (H8)
Daytime running lamps: 13 W (P13W)
Type 2
Daytime running lamps: 13 W (P13W)
5. Side turn-signal lamps (on fender)* 1
, * 2
:
5 W
6. Side turn-signal lamps (on outside rear-
view mirror)* 1
Vehicles with high intensity discharge
headlamps 1. Front turn-signal lamps: 21 W (PY21W)
2. Position lamps/Daytime running lamps
3. Headlamps, high/low beam: 25 W (D5S) 4. Front fog lamps: 19 W (H16)
5. Side turn-signal lamps (on fender)* 1
, * 2
:
5 W
6. Side turn-signal lamps (on outside rear-
view mirror)* 1*
1
:if so equipped* 2
:Have the lamps bulbs replaced
at a MITSUBISHI MOTORS
Authorized Service point.
Codes in parentheses indicate bulb types.
Replacement of lamp bulbs
10-22OKTE17E1Maintenance10