Front suspension MITSUBISHI LANCER 2006 Owner's Manual

ON-VEHICLE SERVICE
REAR SUSPENSION34-7
Carry out adjustment by turning the toe adjusting bolt
(control link mounting bolt which is located on the
inner side of the body).
NOTE: .
•LH: Clockwise viewed from the front → To e - i n
•RH: Clockwise viewed from the front → Toe-out
•Turning the toe adjusting bolt by one groove of
the scale, toe can be changed approximately 2.6
mm (single side toe angle equivalent to 16').
CONTROL LINK PILLOW BALL BUSHING
AXIAL PLAY CHECK
M1341018500066
1. Raise the vehicle.
AC304398ABControl link pillow ball bushing
Front of
vehicle
2.Move the control link up and d o wn with your
ha nds to ch eck for an excessive pla y in the a x ia l
direct ion o f the p illow ball bushing . If the r e is an
exce ssive play , re place the cont rol link (Re f er to
P.34-8).
UPPER ARM PILLOW BALL BUSHING
AXIAL PLAY CHECK
M13410184 0006 9
1.Raise th e ve hicle.
AC304398AC
Upper arm pillow
ball bushing
Front of
vehicle
2. Move the up per arm up and down with you r hand s
to che ck for an e xce ssive play in the axial
d i rection o f the p illow ball bushing . If the r e is an
e xce ssive play , re place the upper arm (Refe r to
P.34-8).
LOWER ARM PILLOW BALL BUSHING
AXIAL PLAY CHECK
M13410169 0005 7
1.Raise th e ve hicle.
2.Remove the st a b ilizer link and shock a b sorb er
f r om t h e l o we r arm a s s e mb l y .
AC304398ADLower arm pillow ball bushing
Front of
vehicle
3.Move the lower a r m u p and down with your h ands
to che ck for an e xce ssive play in the axial
d i rection o f the p illow ball bushing . If the r e is an
e xce ssive play , re place the lower a r m pillo w b a ll
b u shing (Refer to
P.34-10).
4.Af ter inspe c tio n , in st all the st a b ilizer link and
shock a b sorb er to the lower arm assembly (Refer
to
P.34-8).
STABILIZER LINK BALL JOINT DUST
COVER INSPECTION
M1341 0128 0027 4
1.Check st abilize r lin k ba ll joint dust covers f o r
cracks o r damage by pushing it wit h you r fing er .
2. If a du st cove r is crack ed or da mag ed, rep l ace t he
st a b ili zer link assembly .
NOTE: Cracks or dama ge to t he dust co ver may
cause damage to the b a ll join t.

TRAILING ARM ASSEMBLY
REAR SUSPENSION34-13
REMOVAL SERVICE POINTS
<> LIFTING POINT
AC006171AC
Trailing arm
When removing the tra
iling arm, move the lif t ing arm
slightly towards the
front of the vehicle so tha t it will
not be
in the way .
<> LOWER ARM ASSEMBL Y AND
TRAILING ARM DISCONNECTION
AC107126AB
Piece of wood
After supporting the lo we r a r m assembly with a jack,
sep
a rate the lower arm assemb ly a nd trailin g arm
conn
ection.
INST ALLA T ION SER VICE POINT
>>A<< STABILIZER LINK INST ALLA TION
AC103744
A
AC
Ti ghten the self-locking nut un til t he st ab ilizer link
thread
p a rt protrud i ng length mee t s the st a ndard
value.
St andard va lue (A): 6 − 8 mm
INSPECTION
M13410023 0018 2
•Check the bushing s for wea r and d e terio r ation .
•Check the trailing arm fo r bend ing o r damage.
TRAILING ARM BUSHING
REPLACEMENT
M134101 13 0022 1
AC006172AE
Driving out
MB990890
Trailing arm MB990947
MB991816
1.Use the f o llo wing special t ools to drive o u t the
tra iling arm bushing .
•Rear suspension bu shing base (MB99089 0)
•Lower arm b u shing arb o r (MB99 0947)
•
AC006173 AB
Bushing remover an d inst alle r base (MB99 1816)
2.Set the in st allation dire ctio n and inst allation
locat i on o f the tra iling arm bushin g .
(1) P lace the long projectio n end of the t r ailing
arm bush i ng inner p i pe t o wards the in sid e of
the vehicle .
(2) M a k e sure tha t the h o llo w of the t r ailing a r m
bushing is located as sh own in the illustration.
<>9.Lower a rm assemb ly a nd tra iling
ar
m conn ection
10.Tr ailing arm and body connection
11.Tr ailing arm
Re mo va l st ep s ( C o n t in u e d)