wheel size MITSUBISHI LANCER 2006 Workshop Manual

GENERAL INFORMATION
WHEEL AND TYRE31-2
GENERAL INFORMATION
M1311000100350
The wheels and tyres of the following specifications
have been established.
SPECIFICATIONS
ROAD WHEEL AND TYRE
ItemInviteIntense
WheelTy p eSteel type or Aluminium type*Aluminium type
Size15 × 6JJ16 × 6JJ
Amount of wheel offset mm4646
PCD mm11 4 . 3114.3
Ty r eSize195/60R15 88H195/50R16 84V
SPARE WHEEL AND TYRE
ItemInviteIntense
Spare
wheelTy p eSteel typeSteel type
Size16 × 4T or 15 × 6JJ*16 × 4T or 16 × 6JJ*
Amount of wheel offset mm4640 or 46*
PCD mm11 4 . 3114.3
Spare tyreSizeT125/70D16 96M or
195/60R15 88H*T125/70D16 96M or
195/50R16 84V*
NOTE: .
•The * mark indicates optional item.
•PCD (Pitch Circle Diameter) indicates the pitch circle diameter of the wheel installation holes.
SERVICE SPECIFICATIONS
M1311000300398
ItemLimit
Tread depth of tyre mmMinimum 1.6
Wheel runout

Radial runout mm1.0 or less
Lateral runout mm1.0 or less
Wheel runout

Radial runout mm1.2 or less
Lateral runout mm1.2 or less

TROUBLESHOOTING
WHEEL AND TYRE31-4
WHEEL BALANCE ACCURACY
M1311001700247
PURPOSE
This section contains tips and procedures for achiev-
ing accurate wheel balance. Steering wheel vibration
and/or body shake can result if any of these proce
-
dures are not carefully observed.
1. Wheels and tyres must be properly mounted on a balancer in order to achieve correct balance.
Centring the wheel on the shaft of the balancer is
essential for proper mounting.
2. Off-the-car wheel balancers must be calibrated periodically to ensure good balancing results. An
inaccurately calibrated balancer could cause
unnecessary replacement of tyres, shocks,
suspension components, or steering components.
Check your balancer's calibration approximately
every 100 balances. Your wheel balancer's instruc
-
tion manual should include calibration procedures. If
the calibration procedures specifically for your bal
-
ancer are missing, use the generic steps in this sec-
tion for zero calibration, static balance, and dynamic
balance checks. The wheel balancer calibration
checks are also described in the flowchart. (Refer to
P.31-6).
PROCEDURE
1. Confirm that the balancer's cone and the wheel
mounting cone are undamaged and free of dirt
and rust.
2. On this vehicle, the wheel's centre hole on the hub side has a chamfered edge. Use a
back-mounting cone on your wheel balancer to
centre the wheel on the balancer shaft.
3. Install a wheel mounting cone. The appropriate size cone for this vehicle is 67.0 mm.
4. Before balancing the wheel, remove any wheel weights from both sides. Also check both sides for
any damage.
5. When installing wheel weights, hammer them at a straight (not diagonal) angle.
Scalloped
wear
ACX00934
Lack of rot a tio n of tyres or worn
or out-of-a
lign m ent suspensionRota te th e tyre s, an d
check the f
r ont or
rea
r suspension
alignment
s.
Refer to GROUP
33
, On -vehicle
serv
ic e
− Front
whee
l alignment
check and
ad
justmen t
P.33-6.

Refer to GROUP
34
, On -vehicle
serv
ic e
− Rear
whee
l alignment
check and
ad
justmen t
P.34-6.
Sy mptom P robable cause Reme dy Referen ce p a g e