change key battery MITSUBISHI LANCER 2016 8.G Owners Manual

Keyless
entry
system
(if
so
equipped)
5-10
Features and controls
5
1.Have
available
all (current
and
new)
remote
control
transmitters
you
wish
to
registe
r.
2.With
a valid
(already
registered)
remote
control
transmitte
r, press
the
UNLOCK
button
(2)
for
4 to 10
seconds.
Then
press
and hold the LOCK button (1).3.Within
10
seconds
of
pressing
the
LOCK
button,
release
the
LOCK
and
UNLOCK
buttons in sequence.At
this
time,
ID
codes
for
all
remote
con-
trol
transmitters
except
for
the
transmitter
used
in
steps
2 and
3 are
erased
and
the
answerback
function
(door
is locked
and
unlocked)
informs
you
that
the
registra-
tion mode has been activated.4.Within
60
seconds
after
step
3, complete
the
following
ID
code
registration
opera-
tion
using
the
next
remote
control
trans-
mitter
you
wish
to
register
within
4seconds.i.Press
both
the
LOCK
and
UNLOCK
buttons
for
2 seconds.
ii.Release
both
the
LOCK
and
UNLOCK
buttons
for
1 second.
iii.
Press the UNLOCK button.The
answerback
function
informs
you
that
the
ID
code
registration
of
the
transmitter is completed.
5.To register
the
ID
codes
of
additional
remote
control
transmitters,
repeat
step
4
within 60 seconds after step 4.
6.If no
ID
code
of
a remote
control
trans-
mitter
is
registered
within
60
seconds
after
step
4, the
registration
mode
is can-
celed
and
the
normal
mode
returns.
N00546
101111
Your
keyless
entry
system
operates
on
a radio
frequency
subject
to
Federal
Communica-
tions
Commission
(FCC)
Rules
(For
vehicles
sold
in
U.S.A.)
and
Industry
Canada
Rules
(For
vehicles
sold
in
Canada).
This
device
complies
with
Part
15
of
FCC
Rules
and
Industry
Canada
licence-exempt
RSS
stan-
dard(s).Operation
is subject
to the
following
two
con-
ditions
.
This
device
may
not
cause
harmful
inter
-
ference.
NOTE
For
verification
purpose
s, try
to lock and
unl
ock the doors
after the registration
is
completed
.
The
indicator
light
(5)
comes
on
each
time
a
button
is pressed.
The keyless
entry
system
doe
s not
work
if
the key is in the ignition switch
.
The
remo
te con
trol trans
mitter
can
be use
d
from
about
40 feet
(12 m) away. However
,
this
distan
ce
may
change
if your
vehicle
is
near
a TV
transmitting
tower
, a power
sta-
tion, or a radio station.If the UNL
OCK
button
(2)
is pre
ssed whe
n
all
doors
are
locked
and
no
doors
are
opened
within about
30
seconds,
the doors
will auto-
matically
re-lock.
If the
following
conditions
are
observed
after
pressing
the
buttons
on
the
remote
control
transmitter
, the battery
in the remo
te cont
rol
transmitter
may need
to be
replaced
.
•The doors
cannot
be locked or unl
ocked.
•The trunk
lid cannot
be ope
ned.
•The panic
alarm
cannot
be operated.
•The
indicator
light
(5)
is dim
or
does
not
come
on.
If you
lose
your
remote
control
transmitter
,
pleas
e contact
an authorized
Mitsubi
shi
Motors dealer for a replacement.If you
wish to obtain
an additional
remote
control
transmitter
, please
contact
an
autho-
rized
Mitsubishi Motors
dealer
. A max
imu
m
of
eight
remote
control
transmitters
can
be
programmed for your vehicle.To use
the
new
remote
control
transmitters,
it
is necessary
to register
the
key
with
both
the
electronic
immobilizer
and
keyless
entry
sys-
tem. Also refer to “Electr
onic
immobilizer
(Anti-
theft starting
system)
: Cust
omer
key pro-
gramming”
on
page
5-6.
General information

NOTE

Keyless
entry
system
(if
so
equipped)
Features and controls
5-11
5
This
device
must
accept
any
interference
received,
including
interference
that
may
cause undesired operation.
N0054410
1159
1.Before
replacing
the
battery
, remove
static
electricity
from
your
body
by
touching
a
metal
grounded
object.
2.Remove
the
screw
(A)
from
the
remote
control
transmitter
.
3.With
the
Mitsubishi
mark
facing
you,
insert
the
cloth-covered
tip
of
a flat
blade
screwdriver
into
the
notch
in
the
remote
control
transmitter
case
and
use
it to open
the case.
4.Remove the old battery
.
5.Install
a new
battery
with
the
+side
(B)
up.6.Close
the
remote
control
transmitter
case
firmly
.
7.Attach
the
screw
(A)
removed
in step
2.
CAUTIONChanges
or
modifications
not
expressly
approved
by
the
manufacturer
for
compli-
ance coul
d voi
d the use
r’s authority
to ope
r-
ate
the
equipment.
Pr
ocedur
e for r
eplacing the
remote contr
ol transmitter bat-
tery

NOTE
Be
sure
to perform
the
procedure
with
the
Mitsubi
shi mark
facing
you.
If the Mitsubi
-
shi
mark
is not
facing
you
when
you
open
the
remote
control
transmitter
case,
the
buttons
may
come
out.
The
Federal
Communications
Commission
(FCC)
ID
number
, the
Industry
Canada
(IC)
number
and
the
model
number
(radio
certifi-
cation)
are indicated
in the illust
rated
posi
-
tion.NOTE
+ side
- side
Coin
type
battery CR1620

Free-hand Advanced Security Transmit
ter (F.A.S.T.-key) (if so equipped)
Features and controls
5-33
5
5.Turn
the
emer
gency
key
with
F.A.S.T
.-
key
to
the
“ON”
position.
(Perform
the
following procedure within 30 seconds)6.Remove
the
F.A.S.T
.-key
from
the
emer
-
gency key
.
7.With
the
first
valid
F.A.S.T
.-key
, press
the
UNLOCK
button
for
4 to 10
seconds
and
press the LOCK button during this time.8.Release
in
sequence
the
LOCK
and
UNLO
CK
buttons
within
10
seconds
of
pressing
the
LOCK
button
in step
7. (Per
-
form
the
following
procedure
within
30
seconds
)
9.With
the
second
valid
F.A.S.T
.-key
, press
the
UNLOCK
button
for
4 to 10
seconds
and
press
the
LOCK
button
during
this
time.
10.
Release
in
sequence
the
LOCK
and
UNLO
CK
buttons
within
10
seconds
of
pressing
the LO
CK
butt
on
in
step
9, and
the
immobilizer
display
will
blink
on
the
information
screen
in
the
multi-informa-
tion
display
. (Perform
the
following
pro-
cedure within 60 seconds)
11.Press
the
LOCK
button
twice
with
the
blank
F.A.S.T
.-key
and
the
immobilizer
display
will come
on
for
30
seconds
on
the
information
screen
in the
multi-infor
-
mation displa
y.
12.
This
completes
the
registration
of
the
F.A.S.T.-key.
N00561601
074
Your
F.A.S.T
.-key
operates
on
a radio
fre-
quency
subject
to
Federal
Communications
Commission
(FCC)
Rules
(For
vehicles
sold
in
U.S.A.)
and
Industry
Canada
Rules
(For
vehicles
sold
in
Canada).
This
device
com-
plies
with
Part
15
of
FCC
Rules
and
Industry
Canada licence-exempt RSS standard(s). Operation
is subject
to the
following
two
con-
ditions
.
NOTE
The
ind
icator
light
(5)
comes
on each
time
a
button
is pre
ssed.
The
keyless
entry
system
does
not
work
if
the
key
is in the
ignition switch.
The
F.A.S.
T.-key
can
be
used
from
about 40
feet
(12
m)
away
. However
, this
distance
may
change
if your
vehicle
is near
a TV
trans
mitting
tow
er, a pow
er
station,
or
a
radio
station.
If the UNL
OCK
button
(2)
is pre
ssed whe
n
all
doors
are
locked
and
no
doors
are
opened
within
about
30
seconds
, the
doors
will auto-
matically
re-lock.
If the followi
ng
conditions
are obse
rve
d after
pressing
the
buttons
on
the
remote
control
transmitter
, the battery
in the remo
te cont
rol
transmitter
may need
to be replaced
.
•The doors cannot
be locked or unl
ocked.
•The trunk
lid cannot
be ope
ned.
•The panic alar
m cannot
be ope
rated
.
•The
indicator
light
(5)
is dim
or
does
not
come
on.
If you
lose your
F.A.S.T.-key
, pleas
e contact
an authorized
Mitsubis
hi Motors
dealer
for
a
replacement.If you
wish
to obtain
an
additional
F.A.S.T
.-
key, pleas
e con
tact
an authorized
Mitsubi
shi
Motors
dealer
. A max
imu
m of four
F.A.S.T
.-
key can be
pro
grammed fo
r your vehicle.
To use
the
new
remote
control
transmitters,
it
is necessary
to register
the
key
with
both
the
electronic
immobilizer
and
keyless
entry
sys-
tem. Also refer to “Electronic
immobilizer
(Anti-
theft
starting
system):
Customer
F.A.S.T
.-
key programming” on page 5-28.
General
information

NOTE

Door
locks
5-34
Features and controls
5
This
device
may
not
cause
harmful
inte
r-
ference.This
device
must
accept
any
interference
received,
including
interference
that
may
cause undesired operation.
N0056170
0081
1.Before
replacing
the
battery
, remove
static
electricity
from
your
body
by
touching
a
metal
grounded
object.
2.With
the
Mitsubishi
mark
facing
you,
insert
the
cloth-covered
tip
of
a flat
blade
screwdriver
into
the
notch
in
the
remote
control
transmitter
case
and
use
it to open
the case.
3.Remove the old battery
.
4.Install
a new
battery
with
the
+side
(A)
up.
5.Close
the
remote
control
transmitter
case
firml
y.
6.Check
the
keyless
entry
system
to see
that
it works.
N0050920
0491
CAUTIONChanges
or
modifications
not
expressly
approved
by
the
man
ufactur
er for compli-
ance could
void
the user’s authority
to oper
-
ate
the
equipment.
Pr
ocedur
e for r
eplacing the
remote
contr
ol
transmitter
battery

NOTE
Be
sure
to perform
the
procedure
with
the
Mitsubi
shi mark
facing
you.
If the Mitsubi
-
shi
mark
is not
facing
you
when
you
open
the
remo
te cont
rol transmitter
cas
e, the transmit-
ter
may
come
out.
+ side
- side
Coi
n type
bat-
tery
CR203
2
NOTE
You
may
purchas
e a replacement
battery
at
an electric
appliance
store.
Your
authorized
Mitsubi
shi Mot
ors
dealer
can
replace
the battery
for
you
if you
pre
fer.
CAUTIONWhen the remo
te control
transmitter
cas
e is
opened,
be
careful to keep
water
, dust, etc.
out.
Also,
do
not
touch
the
internal
compo-
nen
ts.
Door locks
W
AR
NING
Mak
e sur
e all
doors
are tigh
tly
clos
ed and
locked
while
driving.
•Locked
doors,
in
combination
with
the
use
of seat
belts,
can
help
reduce
the
risk
of ejection
in an
accident.
•Locked
doors
can
help
keep
passengers,
especially
small
childr
en,
from
opening
doors
and
falling
out
of moving
vehicles.

Turn signal lever
Features and controls 5-133
5
N00522601545
When changing lanes, or to making a gradual turn, hold the lever in
the “lane change” posi-
tion (1). It will return to the neutral positionwhen you let go. Use the full position (2) when making a normal turn. The lever will return to the neutral position when the turn iscomplete. There may be times when the lever does not return to the neutral position. This usually happens when the steering wheel isturned only slightly. You can easily return the lever by hand. Also, when you move the lever to (1) slightlythen release it, the turn signal lights and indi- cator light in the instrument cluster will flash three times.
N00522700217
If you press the flasher switch, the front andrear turn signals will flash intermittently, and so will the hazard warning lights. This is an emergency warning system and should not beused when the vehicle is in motion, except foremergencies. If you need to leave your vehicle, the flashers will keep working afte
r the ignition key is
removed.
NOTE
 Start adjusting when the knob is at the “0” position (when the beam is at its highest).  Keep the knob in the “0” position except when using the knob to lower the headlightbeam angle.  Always return the knob to the “0” position when the load is removed and the people have left the vehicle.
Turn signal lever
NOTE
 A light in the instrument panel flashes to show when the front and rear turn signal lights are working properly.If this light flashes faster than usual, check for a burned out light bulb or malfunctioning connection.If the panel light does not come on when the lever is moved, check for a blown fuse or a burned out bulb in the panel.Have the vehicle inspected by an authorized Mitsubishi Motors dealer or a repair facility of your choice.  The turn signal light 3-flash function for lane changes can be deactivated.See your authorized Mitsubishi Motors dealer for details.  You can adjust the time required to operate the lever for the 3-flash function. See your authorized Mitsubishi Motorsdealer for details.
Hazard warning flasher switch
NOTE
 If you keep the flashers on for several hours with the engine turned off, the battery will run down.
BK0230300US.book
133 ページ ２０１５年７月３０日　木曜日　午後８時３８分