brakes MITSUBISHI LANCER EVOLUTION 2007 Service User Guide

PARKING BRAKES -Parking Brake Lever36-5
PARKING BRAKE LEVER
REMOVAL AND INSTALLATION
Pre-removal Operation
Rear Floor Console Assembly and Rear Console
Bracket Removal (Refer to GROUP 52A-Floor Console.)Post-installation Operation
DParking Brake Lever Stroke Adjustment
(Refer to P.36-3.)
DRear Floor Console Assembly and Rear Console
Bracket Installation (Refer to GROUP 52A-Floor
Console.)
54
3
21
Ratchet plateSection A - ASection B - B
Ratchet
pawl
A
B
A
B
Removal steps
1. Adjusting nut
2. Parking brake switch connector
3. Parking brake cable connection4. Parking brake lever assembly
5. Parking brake switch

PARKING BRAKES -Parking Brake Cable36-6
PARKING BRAKE CABLE
REMOVAL AND INSTALLATION
CAUTION
If the vehicle is equipped with the Brembo disc brake, during maintenance, take care not to contact
the parts or tools to the caliper because the paint of caliper will be scratched. And if there is
brake fluid on the caliper, wipe out quickly.
Pre-removal Operation
DRear Floor Console Assembly and Rear Console
Bracket Removal (Refer to GROUP 52A-Floor
Console.)
DRear Seat Cushion Assembly Removal (Refer to
GROUP 52A-Seat.)Post-installation Operation
DParking Brake Lever Stroke Check and Adjustment
(Refer to P.36-3.)
DRear Seat Cushion Installation (Refer to GROUP
52A-Seat.)
DRear Floor Console Assembly and Rear Console
Bracket Installation (Refer to GROUP 52A-Floor
Console.)
1
Removal steps
DShoe and lining assembly
(Refer to P.36-7.)
DParking brake cable connection
(Refer to P.36-5.)
1. Parking brake cable

PARKING BRAKES -Parking Brake Drum36-7
PARKING BRAKE DRUM
REMOVAL AND INSTALLATION
CAUTION
If the vehicle is equipped with the Brembo disc brake, during maintenance, take care not to contact
the parts or tools to the caliper because the paint of caliper will be scratched. And if there is
brake fluid on the caliper, wipe out quickly.
5 11 14
1312
11 10
976
5 43
2 1
11
54¶5Nm 118¶19 Nm
8
Brake grease: Multipurpose grease
Removal steps
AA"1. Rear brake caliper assembly
2. Rear brake disc
"BA3. Shoe-to-anchor spring
4. Adjusting wheel spring
"AA5. Adjuster assembly
6. Strut
7. Strut-to-shoe spring
8. Shoe hold-down cup9. Shoe hold-down spring
10. Clip
11. Shoe and lining assembly
12. Rear hub assembly
(Refer to GROUP 27.)
13. Backing plate
14. Shoe hold-down pin

PARKING BRAKES -Parking Brake Drum36-8
REMOVAL SERVICE POINT
AA"REAR BRAKE CALIPER ASSEMBLY REMOVAL
Remove the rear brake caliper assembly and support it with
wire or similar.
CAUTION: Brembo disc brake
Take care not to contact the parts or tools to the caliper
because the paint of caliper will be scratched. And if
there is brake fluid on the caliper, wipe out quickly.
INSTALLATION SERVICE POINTS
"AAADJUSTER ASSEMBLY INSTALLATION
Install the adjuster assembly so that the shoe adjusting bolt
of left hand wheel is attached towards the rear of the vehicle,
and the shoe adjusting bolt of right hand wheel is towards
the front of the vehicle.
"BASHOE-TO-ANCHOR SPRING INSTALLATION
Install the shoe-to-anchor springs in the order shown in the
illustration.
NOTE
The figure shows the left wheel; for the right wheel, the position
is symmetrical.
INSPECTION
BRAKE LINING AND BRAKE DRUM CHECK
1. Measure the thickness of the brake lining at several places.
Standard value: 2.8 mm
Limit: 1.0 mm
2. If the thickness of the brake lining has worn down to
the limit value or more, replace the shoe and lining
assemblies on both sides of the vehicle.
3. Measure the inside diameter of the brake disc in two
places or more.
Standard value: 168.0 mm
Limit: 169.0 mm
4. If the inside of the brake disc has worn down to the
limit value or more, or if it is excessively worn on one
side, replace the brake disc.
Shoe adjusting
bolt
Rear side
of the ve-
hicle
A14N0009
12
Paint