heater MITSUBISHI LANCER EVOLUTION 2007 Service Owner's Guide

54A-3
SIDE TURN-SIGNAL LAMP 31............
SPECIAL TOOL 31............................
SIDE TURN-SIGNAL LAMP 31..................
ROOM LAMP 31.........................
TROUBLESHOOTING 31.......................
REAR COMBINATION LAMP 32...........
SPECIAL TOOL 32............................
TROUBLESHOOTING 32.......................
REAR COMBINATION LAMP 32................
HIGH-MOUNTED STOP LAMP 34.........
ON-VEHICLE SERVICE 34......................
High-mounted Stop Lamp Bulb Replacement 34.
HIGH-MOUNTED STOP LAMP 34................
LICENCE PLATE LAMP 35...............
ON-VEHICLE SERVICE 35.....................
License Plate Lamp Replacement 35...........
LICENCE PLATE LAMP 35.....................
HAZARD WARNING LAMP SWITCH 36....
SPECIAL TOOL 36............................
HAZARD WARNING LAMP SWITCH 36.........
HORN 37................................
CIGARETTE LIGHTER 37.................
COLUMN SWITCH 38....................
SPECIAL TOOL 38............................
COLUMN SWITCH 38..........................
CLOCK 40...............................
SPECIAL TOOL 40............................
CLOCK 40....................................
POLE ANTENNA 41......................
ROOF ANTENNA 42......................
DEFOGGER 42...........................
TROUBLESHOOTING 42......................
ON-VEHICLE SERVICE 43.....................
Printed Heater Check 43......................
Defogger Relay Continuity Check 43...........
DEFOGGER SWITCH 43.......................

CHASSIS ELECTRICAL -Defogger54A-43
ON-VEHICLE SERVICE
PRINTED HEATER CHECK
(1) With engine running at 2,000 rpm and battery in charging
mode, check print heater for normal operation.
(2) With defogger switch in “ON” position, use circuit tester
to measure voltage of individual print heaters at the center
point A of rear window glass. When the tester indicates
approx. 6V, the print heater is evaluated normal.
(3) When the measured value at Position A is 12V, open
circuit occurs between Position A and minus terminal.
In this case, carefully move test bar to minus terminal
side to detect a rapid voltage drop point (0V). This voltage
drop point indicates open circuit section.
(4) When voltage at Position A is 0V, open circuit occurs
between Position A and plus terminal. According to the
previous step, detect a rapid voltage increase point (12V).
DEFOGGER RELAY CONTINUITY CHECK
Battery voltageTerminal No.yg
1345
De-energized
Energized
DEFOGGER SWITCH
REMOVAL, INSTALLATION AND CHECK
Refer to GROUP 55 - Heater Control Assembly, A/C Switch
and Fresh/Recirculated Air Switch.
(–) Terminal
(–) Terminal
A (Mid point): Approx. 6 V
Normal characteristics of print heater
Abnormal characteristics of print heater
Voltage
Voltage
(+) Terminal
(+) Terminal
Print heater length
Print heater length
Open section
Defogger relay
04Z0001
\

55-1
HEATER, AIR
CONDITIONER AND
VENTILATION
CONTENTS
SERVICE SPECIFICATIONS 2.................
LUBRICANTS 2..............................
SPECIAL TOOLS 2...........................
TROUBLESHOOTING 3.......................
ON-VEHICLE SERVICE 14....................
Refrigerant Level Test through Performance Test 14.
Magnetic Clutch Test 14.........................
Receiver Drier Test 14..........................
Compressor Drive Belt Adjustment 15.............
Dual Pressure Switch Check 15..................
Charging 16...................................
Correcting Low Refrigerant Level in case the Service
can used 18...................................
Discharging System 19..........................
Refilling of Oil in the A/C System 19...............
Performance Test 20............................
Refrigerant Leak Repair 21......................
Blower Relay Continuity Check 22................
A/C Compressor Relay Continuity Check 22........Condenser Fan Relay (LO) Check 23.............
Condenser Fan Relay (HI) Check 23..............
Idle-up Operation Check 24.....................
HEATER CONTROL ASSEMBLY (A/C-ECU)
AND A/C SWITCH 25........................
HEATER UNIT AND BLOWER ASSEMBLY 28.
REGISTOR, BLOWER MOTOR AND
INSIDE/OUTSIDE AIR CHANGE OVER
DAMPER MOTOR 32.........................
EVAPORATOR AND AIR THERMO SENSOR
34 ...........................................
COMPRESSOR 36............................
CONDENSER ASSEMBLY AND CONDENSER
FAN ASSEMBLY 40...........................
REFRIGERANT LINES 42.....................
DUCTS 44...................................
VENTILATION 45.............................

ServiceSpecifications/Lubricants/
Special ToolsHEATER, AIR CONDITIONER AND VENTILATION-55-2
SERVICE SPECIFICATIONS
ItemStandard value
Idlid()NP85050Idlingspeed(rpm):NorPrange850±50Idlingspeed(rpm):NorPrange850±50Idlingspeed(rpm):NorPrange850r50
Idle-up speed (rpm): N or P range850±50
Register resistance (for blower motor)ΩHI - LO (between terminals 1 and 3)2.54g()
HI - ML (between terminals 1 and 6)1.24
HI - MH (between terminals 1 and 4)0.6
Air conditioner compressor air gap mm0.3 – 0.5
Refrigerant temperature switch operating temperature (_C)ContinuitySlightly below 150gppgp()
No continuity150 or higher (until tempera-
ture falls to 120 when OFF)
NOTE* : When disconnected the compressor connector at A/C ON
LUBRICANTS
ItemsSpecified lubricantsQuantity
Compressor oil mLSUN PAG 56130±10
Pipe couplingSUN PAG 56As required
Refrigerant (g)R134a (HFC-134a)550±20
SPECIAL TOOLS
ToolNumberNameUse
MB991367Special spannerFor use on the air conditioner compressor
armature locknut
MB991386Pin
MB991529Diagnosis code
check harnessFor inspecting the air conditioner using a
voltmeter

HEATER, AIR CONDITIONER AND VENTILATION-Troubleshooting55-3
TROUBLESHOOTING
BASIC FLOW OF TROUBLESHOOTING
Refer to Group 00 – How to Use Troubleshooting/Inspection Service Points.
INSPECTION CHART FOR TROUBLE SYMPTOMS
Trouble symptomInspection procedureReference page
Air conditioner not working at all155 - 3
Blower motor not working255 - 4
Air cannot be switched between inside and outside355 - 5
Rear defogger not working455-6
Cold air not coming out from the air outlet555 - 7
Magnet clutch not working normally655 - 8
Condenser fan not working at all755-9
Condenser fan not working only for LO855-10
Condenser fan not working only for HI955-11
INSPECTION PROCEDURE FOR TROUBLE SYMPTOM
Inspection procedure 1
Air conditioner not working at all
Probable cause
The A/C-ECU power supply system (including earth) may be defective.DHarness or connector fault
DA/C-ECU fault
NG
Repair
NG
Check the harness between the Ignition switch (IG2) and the
A/C-ECU, and repair if necessary.
NG
Repair
NG
Check the harness between the A/C-ECU and body earth, and
repair if necessary.
NG
Replace manual air conditioner control panel (A/C-ECU).
OK
Check the trouble
symptoms.
Check the following connectors:
C-32, C-08.
C-32
(2) NG
OK
Check the trouble
symptoms.
Measure at the A/C-ECU connector C-32.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
(1) Voltage between terminal 10 and body earth.
Voltage between terminal 7 and body earth.
OK :Battery voltage
(2) Continuity between terminals 12 and body earth.
Continuity between terminals 3 and body earth.
OK :Continuity(1) NGCheck the following connectors:C-32, C-209, C-210
OK
Check the trouble
symptoms.

HEATER, AIR CONDITIONER AND VENTILATION-Troubleshooting55-4
Inspection procedure 2
Blower motor not working
Probable cause
If the blower motor does not work, the blower motor circuit system may be
defective.DBlower motor fault
DHarness or connector fault
DA/C-ECU fault
NG
Replace
NG
Check the harness between the Ignition switch (IG2) and the
blower relay, and between fusible link No. 1 and the blower
relay, and repair if necessary.
OK
Check the trouble
symptoms.
NG
Repair
NG
Replace
OK
Check the resister. (Refer to P.55-32.)
NG
Replace
OK
Check the blower switch. (Refer to P.55-25.)
NG
Replace
OK
Check the blower relay. (Refer to P.55-22.)
NG
Repair
NG
Check the harness between the blower relay and body earth,
and repair if necessary.
OK
Check the trouble
symptoms.
Check the following connectors:
C-215, C-213.
C-215, C-213, C-08
(3) NG
OK
OK
(1) NG
Check the following connectors:C-215, C-210.
NG
Check the harness between the Ignition switch (IG2) and the
blower relay, and between fusible link No. 1 and the blower
relay, and repair if necessary.
OK
Check the trouble
symptoms.Repair
Check the following connectors:
C-215, C-211, C-132
C-215, C-11, C-35, C-132
(2) NG
Measure at the blower relay connector C-215.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
(1) Voltage between terminals 1 and body earth
OK :Battery voltage
(2) Voltage between terminals 5 and body earth
OK :Battery voltage
(3) Continuity between terminal 3 and body earth
OK :Continuity
To the next page
Check the blower motor. (Refer to P.55-32.)

HEATER, AIR CONDITIONER AND VENTILATION-Troubleshooting55-5
NG
Repair
NG
Repair
NG
Check the harness between the blower motor and the body
harness, and repair if necessary.
OK
Check the trouble
symptoms.
NG
Check the harness between the blower motor and the blower
relay, and repair if necessary.
OK
Check the trouble
symptoms.
Check the following connector:C-14.
(2) NG
OK
Check the trouble
symptoms.
NG
Check the harness between the blower switch and the
register, and between the register and blower motor, and
repair if necessary.
NG
Repair
OK
Measure at the blower motor connector C-14.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DBlower switch position:4
(1) Voltage between terminal 1 and body earth
OK :Battery voltage
(2) Continuity between terminal 2 and body earth
OK :Continuity(1) NG
From the previous page
Check the following connectors:C-131, C-16, C-14.
Check the following connectors:C-215, C-210, C-131, C-14.
Inspection procedure 3
Air cannot be switched between inside and outside.
Probable cause
If the air cannot be switched between the inside and outside even though the
inside/outside switch is ON, the inside/outside changeover damper motor system
may be defective.DInside/outside air changeover damper motor fault
DHarness or connector fault
DA/C-ECU fault
NG
Replace
NG
Repair
OK
OK
Check the following connectors:C-10, C-107, C-32.
NG
Check the harness between the Ignition switch (IG2) and the
inside/outside air changeover damper motor, and repair if
necessary.
OK
Check the trouble
symptoms.
NG
Repair
OK
Measure at the inside/outside air changeover damper motor
connector C-10.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DVoltage between terminal 7 and body earth.
OK :Battery voltageNGCheck the following connectors:C-10, C-107, C-102, C-209,
C-210.
Check the inside/outside air changeover damper motor (Refer
to P.55-32.).
NG
Repair
OK
Replace manual air conditioner control panel (A/C-ECU).
NG
Check the trouble
symptoms.
Check the harness between the inside/outside air changeover
damper motor and the A/C-ECU.

HEATER, AIR CONDITIONER AND VENTILATION-Troubleshooting55-6
Inspection procedure 4
Rear defogger not working
Probable cause
If the rear window defogger does not work even though the rear defogger switch
is ON (a 20-minute timer operates), the defogger relay system may be defective.DDefogger relay fault
DHarness or connector fault
DA/C-ECU fault
NG
Check the harness between the ignition switch (IG2) and the
defogger relay, and repair if necessary.
NG
Repair
Replace manual air conditioner control panel (A/C-ECU).
OK
OK
Check the trouble
symptoms.
NG
Check the following connectors:C-214, C-213, C-32.
OK
Check the trouble
symptoms.
NG
Replace
NG
Repair
NG
Check the harness between fusible link No. 1 and defogger
relay, and repair if necessary.
OK
Check the trouble
symptoms.
Check the following connectors:
C-214, C-211, C-132.
C-214, C-211, C-35, C-132
(2) NG
NG
Repair
NG
Check the harness between the defogger relay and the choke
coil, and repair if necessary.
OK
Check the trouble
symptoms.
Check the following connectors:
C-214, C-216, F-19.
C-214, C-217, F-19
NG
Repair
Check the following connectors:F-06.
OK
OK
Measure at the choke coil connector F-19.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DVoltage between terminal 1 and body earth.
OK :Battery voltageNG
OK
Measure at the defogger relay connector C-214.
DDisconnect the connector and measure at the junction box
side.
DIgnition switch: ON
(1) Voltage between terminal 1 and body earth.
OK :Battery voltage
(2) Continuity between terminal 5 and body earth.
OK :Battery voltage(1) NGCheck the following connectors:C-214, C-210.
OK
Check the trouble
symptoms.
NG
RepairNG
Check the harness between body earth and defogger.
NG
RepairNG
Check harness between the defogger relay and A/C-ECU.
OK
Replace choke coil.
Check the defogger (Refer to Group 54A – Defogger.).

HEATER, AIR CONDITIONER AND VENTILATION-Troubleshooting55-7
Inspection procedure 5
Cold air not coming out from the air outlet
Probable cause
If cold air does not come out from the air outlet, the amount of refrigerant may
be inappropriate or the compressor circuit system may be defective.DRefrigerant line fault
DAmount of refrigerant fault
DCompressor fault
DCompressor relay fault
DDual pressure switch fault
DEngine-ECUfault
DA/C-ECU fault
OK
NG
Repair
NG
Check the harness between the A/C compressor relay and the
ignition switch (IG2), and repair if necessary.
OK
Check the trouble
symptoms.
Check the following connectors:
C-12X, C-130, C-102, C-209, C-210
C-12X, C-128, D-102, C-209, C-210NG
Repair
Check the following connectors:
C-12X, A-13, A-47.
C-12X, A-136, A-47.
OK
OK
Check the trouble
symptoms.
NG
OK
NG
Replace
OK
OK
OK
NG
Check the harness between the battery and the A/C
compressor relay., and repair if necessary.
OK
Check the trouble
symptoms.
Check the following connectors:
B-12X, A-43
B-12X, C-136.(1) NG
RepairNG
(2) NG
OK
Check the dual pressure switch.
OK
NG
Repair
Check the harness between the A/Compressor relay and the
A/Compressor.
NG
Repair
Check the following connectors:B-12X, C-126.
OK
Check the trouble
symptoms.
NG
OKNG
Repair
Check the harness between the A/Compressor relay and the
Engine-ECU.
To the next page
Check refrigerant for leakage.
NG
Replace
NG
Replace
NG
NG
Replace
Check the amount of refrigerant.
Check the compressor relay.
Check the compressor magnetic clutch.
Check the refrigerant temperature switch.
Measure at the compressor relay B-12X.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
(1) Voltage between terminal 1 and body earth.
OK :Battery voltage
(2) Continuity between terminal 2 and body earth.
OK :Battery voltage
Refer to Inspection procedure 6 magnet clutch not working
normally.

HEATER, AIR CONDITIONER AND VENTILATION-Troubleshooting55-8
Repair
Repair
NG
Replace the A/C-ECU .
Replace the Engine-ECU .
NG
Repair
Check the following connectors:
A-36, C-111, C-130, C-122, C-32.
A-36, C-111, C-128, C-122, C-32.
OK
Check the trouble
symptoms.
NG
OKNG
Check the harness between the dual pressure switch and the
Engine-ECU.
Check the following connectors:C-32, C-111, A-36.
OK
NG
OKNG
Check the harness between the dual pressure switch and the
A/C-ECU.
From the previous page
Check the trouble
symptoms.RepairNG
Inspection procedure 6
Magnet clutch not working normally
Probable cause
If the magnet clutch does not work normally, the field core or the compressor
may be defective.DCompressor fault
DField core fault
Replace the field core.
Is not the Compressor locked ?NGReplace the compressor and field core.
No