relay MITSUBISHI LANCER EVOLUTION 2007 Service Workshop Manual

MPI -Troubleshooting13A-36
OK
Intermittent Malfunction
(Refer to GROUP 00 - Points to Note
for Intermittent Malfunction.)
OK
MUT-IIData list
DNo. 22 Crank angle sensor
(Refer to P.13A-103.)NGReplace the engine-ECU.
OK
Intermittent Malfunction
(Refer to GROUP 00 - Points to Note
for Intermittent Malfunction.)
OK
Check the trouble symptos.NGReplace the crank angle sensor.
OK
Check for crank angle sensor vane.NGReplace the crank angle sensor vane. NG
OK
Check the harness between the crank
angle sensor and body earth.
DCheck for damage of the earth
wire.Repair NG
OK
Check the harness between the crank
angle sensor and engine-ECU.
DCheck for damage of the output
wire.Reapir NG
OK
Check the following connector:
C-115Repair NG
OK
Check the harness between the crank
angle sensor and engine control relay.
DCheck for damage of the power
cable.Repair
OK
Measure the output waveform at the
B-121 crank angle sensor connector
(using an analyzer).
DUsing the test harness
(MD998478), connect the
connector, and measure at the
pickup harness.
DEngine: Idle
DVoltage between terminal No.2 and
earth.
OK:The waveform shown on
P.13A-117 (Inspection Proce-
dure Using Analyzer), should
be output,and the maximum
value should be more than
4.8 V, and the minimum value
less than 0.6 V. No noise
should be detected in the
output waveform.NGCheck the following connector:
B-11XNG
Repair
From the previous page

MPI -Troubleshooting13A-37
Code No. P0340 Camshaft position sensor systemProbable cause
Inspection Range
DIgnition switch: ON
DThe engine speed is approximately 50 r/min or more.
Evaluation Conditions
DThe sensor output voltage does not change for 2 seconds (no pulse signal output)DMalfunction of camshaft position sensor
DOpen or short circuit in the camshaft position sensor
or loose connector contact
DMalfunction of engine-ECU
OK
To the next page
(3) NGCheck the harness between the
camshaft position sensor connector
and body earth, and repair if
necessary.
DCheck for open circuit and damage
of the earth wire.
OK
Intermittent Malfunction
(Refer to GROUP 00 - Points to Note
for Intermittent Malfunction.)
OK
Check the trouble symptoms.NGReplace the engine-ECU.
OK
Check the harness between the
camshaft position sensor and
engine-ECU.
DCheck for short circuit of the output
wire.NG
Repair
NG
Check the following connector:
C-115NG
Repair
OK
Check the harness between the
camshaft position sensor and
engine-ECU and repair if necessary.
DCheck for open circuit of the output
wire.NG
Repair
(2) NGMeasure at the C-115 engine-ECU
connector.
DMeasure the engine-ECU terminal
voltage.
DDisconnect the camshaft position
sensor connector B-116.
DIgnition switch: ON
DVoltage between terminal No. 88
and earth.
OK:4.9 - 5.1 VOKCheck the following connector:
C-115
OK
Check the harness between the
camshaft position sensor connector
and engine control relay, and repair if
necessary.
DCheck for open circuit and short
circuit of the power cable.
OK
Measure at the B-116 camshaft
position sensor connector.
DDisconnect the connector to
measure at the harness side
(1) Voltage between terminal No. 3 and
earth.
(Ignition switch: ON)
OK:System voltage
(2) Voltage between terminal No. 2 and
earth.
(Ignition switch: ON)
OK:4.9 - 5.1 V
(3) Resistance between terminal No. 1
and earth.
OK:Less than 2Ω(1) NGCheck the following connector:
B-11XNG
Repair
Check the following connector:
B-116NG
Repair

MPI -Troubleshooting13A-38
OK
Intermittent Malfunction
(Refer to GROUP 00 - Points to Note
for Intermittent Malfunction.)
OK
Check the trouble symptoms.NGReplace the engine-ECU.
OK
Intermittent Malfunction
(Refer to GROUP 00 - Points to Note
for Intermittent Malfunction.)
OK
Check the trouble symptos.NGReplace the camshaft position sensor.
OK
Check the camshaft position sensing
cylinder.NGReplace the camshaft position sensing
cylinder. NG
OK
Check the harness between the
camshaft position sensor and body
earth.
DCheck for damage of the earth
wire.Repair NG
OK
Check the harness between the
camshaft position sensor and
engine-ECU.
DCheck for damage of the output
wire.Reapir NG
OK
Check the following connector:
C-115Repair NG
OK
Check the harness between the
camshaft position sensor connector
and engine control relay.
DCheck for damage of the power
cable.Repair
OK
Measure the output waveform at the
B-116 camshaft position sensor
connector (using an analyzer).
DUsing the test harness
(MB991709), connect the
connector, and measure at the
pickup harness.
DEngine: Idle
DVoltage between terminal No. 2
and earth.
OK:The waveform shown on
P.13A-117 (Inspection Proce-
dure Using Analyzer), should
be output,and the maximum
value should be more than
4.8 V, and the minimum value
less than 0.6 V. No noise
should be detected in the
output waveform.NGCheck the following connector:
B-11XNG
Repair
From the previous page

MPI -Troubleshooting13A-39
Code No. P0403 EGR control solenoid valve systemProbable cause
Inspection Range
DThe battery voltage is 10 V or more.
Evaluation Conditions
DSolenoid coil’s surge voltage (battery voltage +2 V) is not detected when EGR
control solenoid valve is turned OFF from ON.DEGR control solenoid valve malfunction
DEGR control solenoid valve circuit disconnection,
short-circuit, or connector contact defect
DEngine-ECU malfunction
OK
To the next page
OK
Check the harness between the EGR
control solenoid valve and
engine-ECU.
DCheck for damage of the output
cable.NG
Repair
OK
Check the following connector:
C-126NG
Repair
OK
Check and repair the harness between
the EGR control solenoid valve and
engine-ECU.
DCheck for disconnection and
short-circuit of the output cable.
OK
Measure at the C-126 engine-ECU
connector.
DDisconnect the connector to
measure at the harness side
DIgnition switch: ON
DVoltage between terminal No. 6 and
earth
OK:System voltageNGCheck the following connectors:
B-14, C-126NG
Repair
OK
Check and repair the harness between
the EGR control solenoid valve and
engine control relay.
DCheck for disconnection and
short-circuit of the power cable.
OK
Measure at the B-112 EGR control
solenoid valve connector.
DDisconnect the connector to
measure at the harness side.
DIgnition switch: ON
DVoltage between terminal No. 1 and
earth
OK:System voltageNGCheck the following connectors:
B-11X, B-14NG
Repair
OK
Measure at the B-112 EGR control so-
lenoid valve connector.
DDisconnect the connector to
measure at the solenoid valve side.
DResistance between terminal No. 1
and terminal No. 2
OK:29 - 35Ω(at 20_C)NGReplace the EGR control solenoid
valve.
NG
Check the following connector:
B-112NG
Repair
MUT-IIActuator test
DNo.10: EGR control solenoid valve
OK:Operation sound is heard,
and there is vibration.OKIntermittent malfunction
(Refer to GROUP 00 - Points to Note
for Intermittent Malfunctions.)

MPI -Troubleshooting13A-40
NG
Replace the engine-ECU.
OK
MUT-IIActuator test
DNo. 10: EGR control solenoid valve
OK:Operation sound is heard,
and there is vibration.OKIntermittent malfunction
(Refer to GROUP 00 - Points to Note
for Intermittent Malfunctions.)
OK
Check the harness between the EGR
control solenoid valve and engine
control relay.
DCheck for damage of the power
cable.NG
Repair
From the previous page

MPI -Troubleshooting13A-41
Code No. P0443 Purge control solenoid valve systemProbable cause
Range of check
DIgnition switch: ON
DBattery voltage is 10 V or more.
Set Conditions
DThe solenoid coil surge voltage (battery voltage +2 V) is not detected when the
purge control solenoid valve is turned from ON to OFF.DMalfunction of the purge control solenoid valve
DOpen or short circuit in the purge control solenoid
valve circuit or loose connector contact.
DMalfunction of Engine-ECU
OK
To the next page
OK
Check the harness between the purge
control solenoid valve and
engine-ECU.
DCheck for damage of the output
cable.NG
Repair
OK
Check the following connector:
C-126NG
Repair
OK
Check and repair the harness between
the purge control solenoid valve and
engine-ECU.
DCheck for disconnection and
short-circuit of the output cable.
OK
Measure at the C-126 engine-ECU
connector.
DDisconnect the connector to
measure at the harness side.
DIgnition switch: ON
DVoltage between terminal No. 9 and
earth
OK:System voltageNGCheck the following connector:
C - 126NG
Repair
OK
Check and repair the harness between
the purge control solenoid valve and
engine control relay.
DCheck for disconnection and
short-circuit of the power cable.
OK
Measure at the B-23 purge control
solenoid valve connector.
DDisconnect the connector to
measure at the harness side.
DIgnition switch: ON
DVoltage between terminal No. 2 and
earth
OK:System voltageNGCheck the following connector:
B-11X
OK
Measure at the B-23 purge control so-
lenoid valve connector.
DDisconnect the connector to
measure at the solenoid valve side.
DResistance between terminal No. 1
and terminal No. 2
OK:30 - 34Ω(at 20_C)NGReplace the purge control solenoid
valve.
NG
Check the following connector:
B-23NG
Repair
MUT-IIActuator test
DNo.08: Purge control solenoid
valve
OK:Operation sound is heard,
and there is vibration.OKIntermittent malfunction
(Refer to GROUP 00 - Points to Note
for Intermittent Malfunctions.)

MPI -Troubleshooting13A-42
NG
Replace the engine-ECU.
OK
MUT-IIActuator test
DNo. 08: Purge control solenoid
valve
OK:Operation sound is heard,
and there is vibration.OKIntermittent malfunction
(Refer to GROUP 00 - Points to Note
for Intermittent Malfunctions.)
OK
Check the harness between the purge
control solenoid valve and engine
control relay.
DCheck for damage of the power
cable.NG
Repair
From the previous page

MPI -Troubleshooting13A-45
OKNG
OK
NG
Check and repair the harness
between the idle speed control servo
and engine control relay.
DCheck for disconnection and
short-circuit of the power cable.
OK
Measure at the B-115 idle speed
control servo connector.
DDisconnect the connector to
measure at the harness side.
DIgnition switch: ON
DVoltage between terminal No. 2
and earth
DVoltage between terminal No. 5
and earth
OK:System voltageOKCheck the following connector:
B-11XNG
NG
OK
Measure at the B-115 idle speed
control servo connector.
DDisconnect the connector to
measure at the idle speed control
servo side.
DResistance between terminal No.
1 and terminal No. 2
DResistance between terminal No.
2 and terminal No. 3
DResistance between terminal No.
4 and terminal No. 5
DResistance between terminal No.
5 and terminal No. 6
OK:28 - 33ΩReplace the idle speed control servo.
Check the following connector:
B-115NG
Repair
NGCheck the harness between the idle speed control servo and
engine-ECU.
DCheck for damage of the output cable.OK
Repair
NGRepair OK
OKRepair
NG
Repair
OK
OK
Check the harness between the idle
speed control servo and engine-ECU.
DCheck for disconnection and
short-circuit of the output cable.NG
Repair
Check the following connector:
C-126
NG
Replace the engine-ECU.
OKIntermittent malfunction (Refer to
GROUP 00 - Points to Note for
Intermittent Malfunctions.)Check the trouble symptoms.
Measure at the C - 126 engine-ECU
connector.
DMeasure the engine-ECU terminal
voltage.
DVoltage between terminal No. 4
and earth
DVoltage between terminal No. 5
and earth
DVoltage between terminal No. 17
and earth
DVoltage between terminal No. 18
and earth
OK:After the warmed engine
completes starting, the volt-
age repeatedly fluctuates
as shown below.

System voltage↔0-6V
OK
Check the following connector:
C-126NG
Repair
Check the harness between the idle sped control servo and
engine control relay.
DCheck for damage of the power cable.
NG
Replace the engine-ECU.
OKIntermittent malfunction (Refer to
GROUP 00 - Points to Note for
Intermittent Malfunctions.)Check the trouble symptoms.

MPI -Troubleshooting13A-47
Code No. P1104 Waste gate solenoid valve systemProbable cause
Inspection Range
DBattery voltage is more than 10 V.
Evaluation Conditions
DSolenoid coil’s surge voltage (battery voltage +2 V) is not detected when the
waste gate solenoid valve turned from ON to OFF.DWaste gate solenoid valve malfunction
DEngine-ECU malfunction
OK
NG
Replace the engine-ECU.
OKIntermittent malfunction (Refer to
GROUP 00 - Points to Note for
Intermittent Malfunctions.)MUT-IIActuator Test
DNo. 12: Waste gate solenoid
valve
OK:Operation sound is heard,
and there is vibration.OKNG
Repair
OK
NG
Intermittent malfunction (Refer to
GROUP 00 - Points to Note for
Intermittent Malfunctions.)
OK
Check the following connector:B-36
MUT-IIActuator Test
DNo. 12: Waste gate solenoid valve
OK:Operation sound is heard,
and there is vibration.
NG
Repair
NGNG
Repair
OK
Check the harness between the
waste gate solenoid valve and
engine-ECU.
DCheck for disconnection and
short-circuit of the output cable.
Check the following connector:C-39
OK
Check the following connector:C-126
Measure at the C-126 engine-ECU
connector.
DDisconnect the connector to
measure at the harness side.
DIgnition switch: ON
DVoltage between terminal No. 11
and earth
OK:System voltageNG
Replace the waste gate solenoid
valve.Measure at the B-36 waste gate
solenoid valve connector.
DDisconnect the connector to
measure at the solenoid valve
side.
DResistance between terminal No.
1 and terminal No. 2
OK:29 - 35Ω(at 20_C)
OK
NG
Measure at the B-36 waste gate
solenoid valve connector.
DDisconnect the connector to
measure at the harness side.
DIgnition switch: ON
DVoltage between terminal No. 1
and earth
OK:System voltage
OKNG
Repair
OK
OK
Check and repair the harness between
the waste gate solenoid valve and
engine control relay.
DCheck for disconnection and
short-circuit of the power cable.
Check the following connector:
B-11X
NG
RepairCheck the harness between the
waste gate solenoid valve and
engine control relay.
DCheck for damage of the power
cable.NG
Repair
OK
Check the harness between the
waste gate solenoid valve and
engine-ECU.
DCheck for damage of the output
cable.

MPI -Troubleshooting13A-48
Code No. P1105 Fuel pressure control solenoid valve
systemProbable cause
Inspection Range
DBattery voltage is more than 10 V.
Evaluation Conditions
DSolenoid coil’s surge voltage (battery voltage +2 V) is not detected when the
fuel pressure control solenoid valve turned from ON to OFF.DFuel pressure control solenoid valve malfunction
DEngine-ECU malfunction
OK
NG
Replace the engine-ECU.
OKIntermittent malfunction (Refer to
GROUP 00 - Points to Note for
Intermittent Malfunctions.)MUT-IIActuator Test
DNo. 09: Fuel pressure control
solenoid valve
OK:Operation sound is heard,
and there is vibration.OKNG
Repair
OK
NG
Intermittent malfunction (Refer to
GROUP 00 - Points to Note for
Intermittent Malfunctions.)
OK
Check the following connector:B-37
MUT-IIActuator Test
DNo. 08: Purge control solenoid
valve
OK:Operation sound is heard,
and there is vibration.
NG
Repair
NGNG
Repair
OK
OK
Check and repair the harness
between the fuel pressure control
solenoid valve and engine-ECU.
DCheck for disconnection and
short-circuit of the output cable.
Check the following connector:
C-126
OK
Check the following connector:C-126
Measure at the C-126 engine-ECU
connector.
DDisconnect the connector to
measure at the harness side.
DIgnition switch: ON
DVoltage between terminal No. 3
and earth
OK:System voltageNG
Replace the fuel pressure control
solenoid valve.Measure at the B-37 fuel pressure
control solenoid valve connector.
DDisconnect the connector to
measure at the solenoid valve
side.
DResistance between terminal No.
1 and terminal No. 2
OK:29 - 35Ω(at 20_C)
OK
NG
Measure at the B-37 fuel pressure
control solenoid valve connector.
DDisconnect the connector to
measure at the harness side.
DIgnition switch: ON
DVoltage between terminal No. 1
and earth
OK:System voltage
OKNG
Repair
OK
OKCheck and repair the harness between
the fuel pressure control solenoid valve
and engine control relay.
DCheck for disconnection and
short-circuit of the power cable.
Check the following connector:
B-11X
NG
RepairCheck the harness between the fuel
pressure control solenoid valve and
engine control relay.
DCheck for damage of the power
cable.NG
Repair
OK
Check the harness between the fuel
pressure control solenoid valve and
engine-ECU.
DCheck for damage of the output
cable.