sensor MITSUBISHI LANCER EVOLUTION IV 1998 User Guide

MPI – Special Tools13-4
SPECIAL TOOLS
ToolNumberNameUse
MB991348Test harness setMeasurement of voltage during trouble-
shooting
Inspection using an oscilloscope
MB991519Alternator harness
connectorMeasurement of voltage during
troubleshooting
MB991536TPS check
harnessAdjustment of idle switch and throttle position
sensor (TPS)
MD998464Test harness
(4-pin, square)Inspection of oxygen sensor
MD998463Test harness
(6-pin, square)Inspection of idle speed control servo
Inspection using an oscilloscope
MD998478Test harness
(3-pin, triangle)Measurement of voltage during trouble-
shooting
Inspection using an oscilloscope
MD998706Injector test setChecking the spray condition of injectors
MD998741Injector test
adaptor
MB991607Injector test
harness

MPI – Troubleshooting13-6
TROUBLESHOOTING
1. DIAGNOSIS FUNCTION
1-1 ENGINE WARNING LAMP (CHECK ENGINE LAMP)
If an abnormality occurs in any of the following items related
to the Multipoint Fuel Injection (MPI) system, the engine
warning lamp will illuminate.
If the lamp remains illuminated or if the lamp illuminates while
the engine is running, check the diagnosis code output.
Engine warning lamp inspection items
Engine-ECU
Air flow sensor (AFS)
Intake air temperature sensor
Throttle position sensor (TPS)
Engine coolant temperature sensor
Crank angle sensor
Camshaft position sensor
Barometric pressure sensor
Detonation sensor
Injector
Ignition coil, power transister
Misfire
1-2 METHOD OF READING AND ERASING DIAGNOSIS
CODES
(1) Use the special tool to earth No.1 terminal (diagnosis
control terminal) of the diagnosis connector.
(2) To check ABS system, remove the valve relay.
NOTE
That is because the valve relay is off and the warning
lamp remains illuminated if there is a fault in the ABS
system.
(3) Turn off the ignition switch.
(4) Read out a diagnosis code by observing how the warning
lamp flashes.
Indication of diagnosis code by warning lamp
When the diagnosis code No.24 is outputWhen no diagnosis code is output*
On
Off
1.5 secs.0.5 sec.
0.5 sec.
Pause
time 3
secs.Tens signalPlace
division
2 secs.Units signal
A03X0113
On
Off
0.5 sec.
0.25 sec.
NOTE
*: Even if the ABS system is normal, removing the valve relay causes the diagnosis code No.52 to
be output.
Engine warning lamp
(check engine lamp)

MPI – Troubleshooting13-7
1-3 ERASING DIAGNOSIS CODES
(1) Turn the ignition switch to OFF.
(2) After disconnecting the battery cable from the battery (–) terminal for 10 seconds or more, reconnect
the cable.
(3) After the engine has warmed up, run it at idle for about 15 minutes.
1-4 FAIL-SAFE FUNCTION REFERENCE TABLE
When the main sensor malfunctions are detected by the diagnosis function, the vehicle is controlled
by means of the pre-set control logic to maintain safe conditions for driving.
Malfunctioning itemControl contents during malfunction
Air flow sensor (AFS)(1) Uses the throttle position sensor signal and engine speed signal (crank angle sensor
signal) to take reading of the basic injector drive time and basic ignition timing from
the pre-set mapping.
(2) Fixes the ISC servo in the appointed position so idle control is not performed.
Intake air temperature
sensorControls as if the intake air temperature is 25C.
Throttle position
sensor (TPS)No increase in fuel injection amount during acceleration due to the throttle position sensor
signal.
Engine coolant
temperature sensorControls as if the engine coolant temperature is 80C.
(This condition is maintained until the ignition switch is turned off even when the sensor signal
returns normal.)
Camshaft position
sensor(1) Injects fuel to all cylinders simultaneously for 4 seconds.
(However, after the ignition switch is turned to ON, the No. 1 cylinder top dead centre
is not detected at all.)
(2) Lets the fan motor (radiator and condensor) run at high speed.
Barometric pressure
sensorControls as if the barometric pressure is 101 kPa {760 mmHg}.
Detonation sensorSwitches the ignition timing from ignition timing for super petrol to ignition timing for standard
petrol.
Ignition coil, power
transistorCuts off the fuel supply to cylinders with an abnormal ignition.
Alternator FR terminalDoes not control the output of the alternator according to an electrical load. (works as a
normal alternator)
Misfire
(Evolution-V only)Cuts off the fuel to the misfiring cylinder if a misfire that could damage the catalyst is detected.

MPI – Troubleshooting13-8
2. INSPECTION CHART FOR DIAGNOSIS CODES
Code No.Diagnosis itemReference page
12Air flow sensor (AFS) system13-8
13Intake air temperature sensor system13-9
14Throttle position sensor (TPS) system13-9
21Engine coolant temperature sensor system13-10
22Crank angle sensor system13-11
23Camshaft position sensor system13-11
24Vehicle speed sensor system13-12
25Barometric pressure sensor system13-13
31Detonation sensor system13-14
41Injector system13-14
44Ignition coil and power transistor unit system13-15
64Alternator FR terminal system13-16
3. INSPECTION PROCEDURE FOR DIAGNOSIS CODES
Code No. 12 Air flow sensor (AFS) systemProbable cause
Range of Check
Engine speed is 500 r/min or more.
Set conditions
Sensor output frequency is 3 Hz or less for 4 seconds.Malfunction of the air flow sensor
Improper connector contact, open circuit or
short-circuited harness wire of the air flow sensor
Malfunction of the engine-ECU
Measure at the air flow sensor con-
nector A-25.
Connect the connector. (Use
the test harness: MB991709)
1. Voltage between 3 and earth
(Engine: Idling)
OK:2.2–3.2 V
2. Voltage between 7 and earth
OK:0–1 V (Engine: idling)
6–9 V (2,000 r/min)
OK
Replace the engine-ECU.1. NG
Check the air flow sensor circuit.
2. NG
Measure at the engine-ECU con-
nector B-59.
Connect the connector.
Voltage between 19 and earth
(Ignition switch: ON)
OK:6–9 V
OK
Check the following connector:
B-59
OK
Check trouble symptom.
NG
Replace the engine-ECU.NG
Check the following connector:
A-25NG
Repair
OK
Check trouble symptom.
NG
NG
Repair
Replace the air flow sensor.

MPI – Troubleshooting13-9
Code No. 13 Intake air temperature sensor systemProbable cause
Range of Check
Ignition switch: ON
Excluding 60 seconds after the ignition switch is turned to ON or immediately
after the engine starts.
Set conditions
Sensor output voltage is 4.6 V or more (corresponding to an intake air temperature
of –45C or less) for 4 seconds.
or
Sensor output voltage is 0.2V or less (corresponding to an intake air temperature
of 125C or more) for 4 seconds.Malfunction of the intake air temperature sensor
Improper connector contact, open circuit or
short-circuited harness wire of the intake air
temperature sensor circuit
Malfunction of the engine-ECU
OK
Check trouble symptom.
Check the intake air temperature sen-
sor. (Refer to P.13-32.)NGReplace air flow sensor.
OK
Measure at the air flow sensor connec-
tor A-25.
Disconnect the connector, and
measure at the harness side.
Voltage between 6 and earth
(Ignition switch: ON)
OK:4.5–4.9 V
Continuity between 5 and earth
OK:ContinuityNGCheck the following connector:
C-62NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between the
engine-ECU and the intake air temper-
ature sensor connector.NG
Repair
OK
Replace the engine-ECU.
OK
Check the following connector:
A-25NG
Repair
NG
Code No. 14 Throttle position sensor (TPS) systemProbable cause
Range of Check
Ignition switch: ON
Excluding 60 seconds after the ignition switch is turned to ON or immediately
after the engine starts.
Set conditions
The sensor output voltage is 0.2 V or less for 4 seconds.Malfunction of the throttle position sensor
Improper connector contact, open circuit or
short-circuited harness wire of the throttle position
sensor circuit
Improper “ON” state of idle position switch
Short circuit of the idle position switch signal line
Malfunction of the engine-ECU
Check the throttle position sensor.NG
Replace
OK
Measure at the throttle position sensor
connector A-16.
Disconnect the connector, and
measure at the harness side.
Voltage between 1 and earth
(Ignition switch: ON)
OK:4.8–5.2 V
Continuity between 4 and earth
OK:ContinuityNGCheck the following connector:
B-62NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between the
engine-ECU and the throttle position
sensor connector.NG
Repair
OK
Replace the engine-ECU. OK
Check the throttle position sensor out-
put circuit.

MPI – Troubleshooting13-10
Code No. 21 Engine coolant temperature sensor systemProbable cause
Range of Check
Ignition switch: ON
Excluding 60 seconds after the ignition switch is turned to ON or immediately
after the engine starts.
Set conditions
Sensor output voltage is 4.6 V or more (corresponding to an engine coolant
temperature of –45C or less) for 4 seconds.
or
Sensor output voltage is 0.1 V or less (corresponding to an engine coolant
temperature of 140C or more) for 4 seconds.Malfunction of the engine coolant temperature sensor
Improper connector contact, open circuit or
short-circuited harness wire of the engine coolant
temperature sensor circuit
Malfunction of the engine-ECU
Range of Check
Ignition switch: ON
Engine speed is approx. 50 r/min or more
Set conditions
The sensor output voltage increases from 1.6 V or less (corresponding to an
engine coolant temperature of 40C or more) to 1.6 V or more (corresponding
to an engine coolant temperature of 40C or less).
After this, the sensor output voltage is 1.6 V or more for 5 minutes.
OK
Check trouble symptom.
Check the engine coolant temperature
sensor. (Refer to P.13-32.)NG
Replace
OK
Measure at the engine coolant temper-
ature sensor connector A-38.
Disconnect the connector, and
measure at the harness side.
Voltage between 1 and earth
(Ignition switch: ON)
OK:4.5–4.9 V
Continuity between 2 and earth
OK:ContinuityNGCheck the following connector:
B-62NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between the
engine-ECU and the engine coolant
temperature sensor connector.NG
Repair
OK
Replace the engine-ECU.
Check the following connector:
A-38NG OK
Repair
NG

MPI – Troubleshooting13-11
Code No. 22 Crank angle sensor systemProbable cause
Range of Check
Engine is cranking.
Set conditions
Sensor output voltage does not change for 4 seconds (no pulse signal input.)Malfunction of the crank angle sensor
Improper connector contact, open circuit or
short-circuited harness wire of the crank angle sensor
Malfunction of the engine-ECU
Measure at the crank angle sensor connector A-51.
Connect the connector. (Use the test harness: MD998478.)
Voltage between 2 (black clip) and earth (Engine: cranking)
OK:0.4–4.0 V
Voltage between 2 (black clip) and earth (Engine: idling)
OK:1.5–2.5 V
NGOKReplace the engine-ECU.
Measure at the crank angle sensor connector A-51.
Disconnect the connector, and measure at the harness side.
1. Voltage between 3 and earth (Ignition switch: ON)
OK:System voltage
2. Voltage between 2 and earth (Ignition switch: ON)
OK:4.8–5.2 V
3. Continuity between 1 and earth
OK:Continuity
OK
Check the following con-
nector: A-51NG
Repair
OK
Check trouble symptom.
NG
Replace the crank angle sensor.1. NG
Check the harness wire between the crank angle sensor and the
control relay connector, and repair if necessary.
2. NGCheck the following con-
nector: B-62NG
Repair
OK3. NG
Check trouble symptom.
NG
Check the harness wire
between the engine-ECU and
the crank angle sensor
connector.NG
Repair
OK
Replace the engine-ECU.
Check the harness wire between the crank angle sensor and the
earth, and repair if necessary.
Code No. 23 Camshaft position sensor systemProbable cause
Range of Check
Ignition switch: ON
Engine speed is approx. 50 r/min or more.
Set conditions
Sensor output voltage does not change for 4 seconds (no pulse signal input.)Malfunction of the camshaft position sensor
Improper connector contact, open circuit or
short-circuited harness wire of the camshaft position
sensor circuit
Malfunction of the engine-ECU
Measure at the camshaft position sensor connector A-97.
Connect the connector.
Voltage between 2 and earth (Engine: cranking)
OK:0.4–3.0 V
Voltage between 2 and earth (Engine: idling)
OK:0.5–2.0 VOKReplace the engine-ECU.
NG
Measure at the camshaft position sensor connector A-97.
Disconnect the connector, and measure at the harness side.
1. Voltage between 3 and earth (Ignition switch: ON)
OK:System voltage
2. Voltage between 2 and earth (Ignition switch: ON)
OK:4.8–5.2 V
3. Continuity between 1 and earth
OK:Continuity1. NGCheck the harness wire between the camshaft position sensor
and the control relay connector, and repair if necessary.
2. NGCheck the following con-
nector: B-62NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire
between the engine-ECU and
the camshaft position sensor
connector.NG
Repair
OK
Replace the engine-ECU. 3. NG
Check the harness wire between the camshaft position sensor
and the earth, and repair if necessary.
OK
Check the following con-
nector: A-97NG
Repair
OK
Check trouble symptom.
NG
Replace the camshaft position sensor.

MPI – Troubleshooting13-12
Code No. 24 Vehicles speed sensor systemProbable cause
Range of check
Ignition switch: ON
Excluding 60 seconds after the ignition switch is turned to ON or immediately
after the engine starts.
Idle position switch: OFF
Engine speed is 3,000 r/min or more.
Driving under high engine load conditions.
Set conditions
Sensor output voltage does not change for 4 seconds (no pulse signal input).Malfunction of the vehicle speed sensor
Improper connector contact, open circuit or
short-circuited harness wire of the vehicle speed
sensor circuit
Malfunction of the engine-ECU
OK
Check the ignition switch. (Refer to GROUP 54 – Ignition Switch.)
2. NG
OK
Replace the engine-ECU.
3. NG
OK
Replace the engine-ECU.
NG
Check the harness wire
between the engine-ECU
and the vehicle speed
sensor connector.NG
Repair
OK
Check trouble symptom.
OK
Check the following
connectors:
A-19, B-62NG
Repair
NG
Check the harness wire
between the engine-ECU
and the vehicle speed
sensor connector.NG
Repair
OK
Check trouble symptom.
Check the following
connector:
B-62NG
Repair
NG
Check the harness wire
between the vehicle
speed sensor and ignition
switch connector.NG
Repair
OK
Check trouble symptom.
OK
Measure at the vehicle speed sensor connector A-19.
Disconnect the connector, and measure at the harness side.
1. Voltage between 1 and earth (Ignition switch: ON)
OK:System voltage
2. Voltage between 3 and earth (Ignition switch: ON)
OK:4.8 – 5.2 V
3. Continuity between 2 and earth
OK:Continuity1. NGCheck the following
connectors:
B-64, B-74, B-76NG
Repair
Check the vehicle speed sensor. (Refer to GROUP 54 – Combina-
tion Meters.)NG
Replace
Check the harness wire between the vehicle speed sensor and
the earth, and repair if necessary.

MPI – Troubleshooting13-13
Code No. 25 Barometric pressure sensor systemProbable cause
Range of Check
Ignition switch: ON
Excluding 60 seconds after the ignition switch is turned to ON or immediately
after the engine starts.
Set conditions
Sensor output voltage is 4.5 V or more (corresponding to a barometric pressure
of 114 kPa {855 mmHg} or more) for 4 seconds.
or
Sensor output voltage is 0.2 V or less (corresponding to a barometric pressure
of 53 kPa {40 mmHg} or less) for 4 seconds.Malfunction of the barometric pressure sensor
Improper connector contact, open circuit or
short-circuited harness wire of the barometric pressure
sensor circuit
Malfunction of the engine-ECU
OK
Replace the air flow sensor.
Measure at the air flow sensor con-
nector A-25.
Connect the connector. (Use
the test harness: MB991709)
Voltage between 2 and earth
(Ignition switch: ON)
OK:3.7–4.3 V (Altitude: 0 m)
3.2–3.8 V
(Altitude: 1,200 m)NGMeasure at the air flow sensor con-
nector A-25.
Disconnect the connector, and
measure at the harness side.
Voltage between 1 and earth
(Ignition switch: ON)
OK:4.8–5.2 V
Continuity between 5 and earth
OK:ContinuityNGCheck the following connector:
B-62NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between
the engine-ECU and the baromet-
ric pressure sensor connector.NG
Repair
OK
Replace the engine-ECU.
OK
Check the following connector:
A-25NG
Repair
OK
Check trouble symptom.Check the harness wire between
the engine-ECU and the baromet-
ric pressure sensor connector.NG
Repair
OK
Measure at the engine-ECU con-
nector B-62.
Connect the connector.
Voltage between 85 and earth
(Ignition switch: ON)
OK:3.7–4.3 V (Altitude: 0 m)
3.2–3.8 V
(Altitude: 1,200 m)NGCheck the harness wire between
the engine-ECU and the baromet-
ric pressure sensor connector, and
repair if necessary.
Check the following connec-
tors:
A-25, B-62
OK
Check trouble symptom.
NG
Replace the engine-ECU.NG
Repair OKNG

MPI – Troubleshooting13-14
Code No.31 Detonation sensor systemProbable cause
Range of Check
Ignition switch: ON
Excluding 60 seconds after the ignition switch is turned to ON or immediately
after the engine starts.
Engine speed is approx. 5,000 r/min or more
Set conditions
The change in the detonation sensor output voltage (detonation sensor peak voltage
at each 1/2 revolution of the crankshaft) is less than 0.06 V for 200 times in succession.Malfunction of the detonation sensor
Improper connector contact, open circuit or
short-circuited harness wire of the detonation sensor
circuit
Malfunction of the engine-ECU
Measure at the detonation sensor con-
nector A-96.
Disconnect the connector and
measure at the harness side.
Continuity between 2 and earth
OK:ContinuityOKCheck the following connector:
B-62NG
Repair
OK
Check trouble symptom.
NG
Check the harness wire between the
engine-ECU and the detonation sensor
connector.OKReplace the detonation sensor.
Check trouble symptom.
NG
Replace the engine-ECU.
NG
Repair
NG
Check the harness wire between the
detonation sensor and earth, and repair
if necessary.
Code No. 41 Injector systemProbable cause
Range of Check
Engine speed is approx. 50–1,000 r/min
The throttle position sensor output voltage is 1.15 V or less.
Set conditions
Surge voltage of injector coil is not detected for 4 seconds.Malfunction of the injector
Improper connector contact, open circuit or
short-circuited harness wire of the injector circuit
Malfunction of the engine-ECU
NG
Check the harness wire between the
resistor and the injector connector, and
repair if necessary.
OK
Check trouble symptom.
OK
Check the injector control circuit.
OK
Measure at the injector connectors
A-53, A-54, A-55, A-56.
Disconnect the connector, and
measure at the harness side.
Voltage between 1 and earth
(Ignition switch: ON)
OK:System voltageNGCheck the following connector:
A-125NG
Repair
Check the injector. (Refer to P.13-34.)
Check the resistor. (Refer to P.13-34.)NG
Replace
OK
Measure at the resistor connector
A-125.
Disconnect the connector, and
measure at the harness side.
Voltage between 3 and earth
(Ignition switch: ON)
OK:System voltageNGCheck the harness wire between the
control relay and the resistor connec-
tor, and repair if necessary.