torque MITSUBISHI LANCER EVOLUTION IV 1998 Repair Manual

PARKING BRAKE – Parking Brake Drum36-8
REMOVAL SERVICE POINTS
ADRIVE SHAFT NUT REMOVAL
BREAR HUB ASSEMBLY REMOVAL
(1) Using the special tool, remove the drive shaft from the
rear hub assembly.
(2) Remove the mounting bolts and remove the rear hub
assembly from the knuckle.
INSTALLATION SERVICE POINT
ADRIVE SHAFT NUT INSTALLATION
(1) Install the drive shaft washer in the direction shown.
(2) Use the special tool as you did during removal and tighten
the drive shaft nut to the specified torque.
Tightening torque: 196 – 255 Nm {20.0 – 26.0 kgf
m}
INSPECTION
BRAKE LINING AND BRAKE DRUM WEAR CHECK
(1) Measure the thickness of the brake lining at a location
that wears most.
Standard value: 2.8 mm
Limit: 1.0 mm
(2) If the measurement exceeds the limit, replace the shoe
& lining assembly of both sides as a set.
(3) Measure I.D. of the brake disc at two or more places.
Standard value: 168.0 mm
Limit: 169.0 mm
(4) If the measurement exceeds the limit or there is an
excessive eccentric wear evident, replace the brake disc.
MB990767
MB990244
(3)
MB990767
MB990242MB991354
Washer

STEERING – Service Specifications / Special Tools / On-vehicle Service37A-2
SERVICE SPECIFICATIONS
ItemsStandard value
Steering angleEVOLUTION-IVInner wheel33
30’ ± 2

Outer wheel28
20’
EVOLUTION-VInner wheel33
10’ ± 2

Outer wheel28
10’
Steering gearPinion total turning torque
Nm {kgfcm}
Total turning torque0.9 – 1.7 {9 – 17}
Nm {kgf
cm}Torque fluctuations0.4 {4} or less
SPECIAL TOOLS
ToolNumberNameUse
MB991197Installer barPressfitting of gear housing oil seal
MB991199Oil seal installer
MB991214Oil seal protectorInstallation of rack assembly
ON-VEHICLE SERVICE
1. STEERING ANGLE CHECK
Locate front wheels on turning radius gauge and measure
steering angle.
Standard value:
Inner wheel
33
30’ ± 2

33
10’ ± 2

Outer wheel
28
20’
28
10’
When the angle is not within the standard value, the toe
is probably incorrect. Adjust toe (Refer to GROUP 33A –
On-vehicle Service) and recheck steering angle.
2. OIL PUMP BELT TENSION CHECK AND
ADJUSTMENT
Refer to GROUP 11 – Engine Adjustments.

STEERING –
Steering Wheel /
Power Steering Gear & Linkage37A-3
STEERING WHEEL

REMOVAL SERVICE POINT
STEERING WHEEL REMOVAL
(1) Peel off the dual lock fasteners from the steering wheel
spokes and remove the horn pad.
(2) Remove the bolts indicated by arrows in the illustration
and remove the steering wheel from the boss plate.
(3) Using the special tool, remove the boss plate from the
steering column.
POWER STEERING GEAR &
LINKAGE
For removal, installation and inspection procedure, follow the
conventional procedures except the following.
INSPECTION
PINION TOTAL TURNING TORQUE
The conventional procedures apply except for the standard
value.
Standard value:
Total turning torque 0.9 to 1.7 Nm {9 to 17 kgf
cm}
Torque fluctuations 0.4 Nm {4 kgf
cm} or less
Dual lock
fastener
Boss plate
MB990803

STEERING – Power Steering Gear & Linkage37A-4
DISASSEMBLY AND REASSEMBLY
1 2
3
4
5 6
7
8 9 10 11 12 13 14 15
16
17
1833
20
35
22 23
24 25 26
27 29
31
Unit: Nm {kgf
m}
22 {2.2}
3034
49 – 59
{5.0 – 6.0}
28
19
21
59 {6.0}
25 {2.5}
59 { 6.0}
1
13 {1.3}
88 {9.0}
7
32
10 2 22
20
18
7
1034
16
30
3128 27
Steering gear seal kit
Flare nut
Repair kit grease
Disassembly steps
1. Feed pipe
2. O-ring
N3. Lock nut
N4. Tie rod end
M5. Dust cover
6. Clip
L7. Band
8. Bellows
K9. Tie rod
K10. Tab washer
JPinion total turning torque adjustment
11. Lock nut
A12. Rack support cover
13. Support spring
14. Rack support
I15. End plug
16. Lock nut
17. Valve housing assemblyBH18. Lower oil seal
B19. Pinion & valve assembly
CG20. Seal ring
DF21. Upper bearing
DF22. Upper oil seal
23. Valve housing
EE24. Circlip
F25. Rack stopper
FD26. Rack bushing
GD27. Oil seal
28. O-ring
FC29. Rack assembly
C30. Seal ring
31. O-ring
HB32. Lower bearing
IB33. Needle bearing
JA34. Oil seal
35. Gear housing

STEERING – Power Steering Gear & Linkage37A-6
JADJUSTMENT OF PINION TOTAL TURNING
TORQUE
(1) With special tool, tighten rack support cover to 15 Nm
{1.5 kgf
m}.
(2) Return rack support cover approx. 30
.
(3) Using the special tools, rotate the pinion shaft at the
rate of one rotation in approximately 4 to 6 seconds to
check that the turning torque and the torque fluctuation
confirm to the standard values.
Standard value:
Pinion total turning torque
0.9 – 1.7 Nm {9 – 17 kgf
cm}
Torque fluctuation 0.4 Nm {4 kgf
cm} or less
(4) If either the turning torque or the torque fluctuation
deviates from the standard value, turn back the rack
support cover within the range of 0 to 30
to adjust it
for the standard value.
Caution
1. When adjusting, set the standard value at its
highest value.
2. Assure no ratcheting or catching when operating
rack towards the axial direction.
3. Be sure to measure the turning torque through
the whole stroke of the rack.
NOTE
If the standard value cannot be obtained by turning back
the rack support cover within the specified angle range,
check rack support cover components and replace as
required.
NTIE ROD END / LOCK NUT INSTALLATION
Turn down the tie rod until the dimension shown in the
illustration is reached; then, temporarily tighten the lock nut.
NOTE
The lock nut is to be tightened to the specified torque after
toe-in has been adjusted with the steering gear & linkage
mounted in the vehicle.
MB990607
MB991006
End of groove in
which bellows fitsLock nut
197.2 mm
212.2 mm

CHASSIS ELECTRICAL – Combination Meters54-30
ENGINE COOLANT TEMPERATURE GAUGE UNIT
CHECK
1. Bleed the engine coolant.
2. Remove the engine coolant temperature gauge unit.
3. Immerse the unit in 70C water to measure the resistance.
Standard value: 104 ±13.5 Ω
4. After checking, apply the specified adhesive around the
thread of engine coolant temperature gauge unit. Then,
tighten the unit to the specified torque.
Specified sealant:
3M Adhesive Nut Locking No. 4171 or equivalent
5. Add engine coolant.
COMBINATION METERS
REMOVAL AND INSTALLATION
2 1
3
Vehicle speed sensor removal
steps

Battery and battery tray

Air cleaner assembly
1. Vehicle speed sensorCombination meter removal steps
2. Meter bezel
3. Combination meter
ThermometerCircuit tester
10 – 12 Nm