engine oil MITSUBISHI LANCER EVOLUTION IX 2005 User Guide

ENGINE – CYLINDER HEAD GASKET
11-15
Removal procedure
1. Ignition coil connector
2. O
2sensor connector
3. Oil feeder control valve connector
4. Crank angle sensor connector
5. Manifold absolute pressure sensor
connector
6. Fuel pressure solenoid valve connector
7. Knock sensor connector
8. Purge control solenoid valve connector
9. Throttle position sensor connector
10. Injector connector
11.Exhaust camshaft position sensor
connector12. Inlet camshaft position sensor
connector
13. Water temperature gauge unit
connector
14. Joint control harness and transmission
harness
15. Water temperature sensor connector
16. Secondary air control solenoid valve
connector
17. Vacuum tank, solenoid valve, vacuum
pipe and hose assembly
18. Brake booster vacuum hose connection
19. Oil level gauge and guide assembly
20. O-ring
21. Purge hose connection
(engine oil)

ENGINE – CYLINDER HEAD GASKET11-16
22. Alternator bracket connection
23. Inlet manifold stay
24. Eye bolt
25. Gasket
26. Eye bolt
27. Gasket
28. Oil feeder control valve pipe
29. Filter
30. Oil pipe joint
31. Gasket
32. Oil return pipe gasket
33. Oil return pipe
34. Oil return pipe gasket35. Oil return pipe gasket
36. Exhaust fitting bracket
•Water outlet fitting and thermostat case
assembly (Refer to Section 14: Water hose
pipe)
37. Water hose connection
38. Heater hose connection
39. Fuel return hose connection
40. Fuel high pressure hose connection
41. O-ring
42. Cylinder head bolt
43. Cylinder head assembly
44. Cylinder head gasket
(when
cool)
(engine oil)
(engine oil)



E 




D 




C 



C 
 
A






B 



A 

ENGINE – CYLINDER HEAD GASKET
11-17
Removal guidelines



A 
Removing the cylinder head bolts
Use the special wrench for cylinder head bolts (MB991654) to turn
the bolts 2~3 times in order to loosen them, before removing them
in the numerical order as shown in the diagram.
Fitting guidelines



A 
Fitting the cylinder head gasket
1. Remove the gaskets which have been stuck onto the surface of
the gasket.
Caution
Do not allow any foreign matter to get into the channels for
coolant or oil, or into the cylinder.
2. Fit the cylinder head gasket to the cylinder head, so that the
holes in the cylinder head gasket match up with the holes in the
cylinder head.



B 
Fitting the cylinder head bolts
1. Check that the length of the body of cylinder head bolts is less
than the maximum permitted. If the length is in excess of the
maximum permitted, replace the bolt with a brand new one.
Maximum length (A): 99.4mm
2. Apply a small amount of engine oil to the screw thread of the
bolt, and to the washer.
Front of engine
(engine oil)

ENGINE – CYLINDER HEAD GASKET11-18
3. Use the special wrench for cylinder head bolts (MB991654) to
(loosely) tighten the bolts in the following order.
(1) In the order shown in the diagram, tighten the bolts to
78 ± 2 N•m.
(2) In reverse order to that shown in the diagram, completely loosen
the bolts.
(3) In the order shown in the diagram, tighten the bolts to
20 ± 2 N•m.
(4) Make a paint mark on the top of the cylinder head bolt, and on
the cylinder head, and tighten them to 90° as shown in the
diagram.
(5) Tighten the bolts to 90° as shown in the diagram, and check that
the paint mark on the top of the cylinder head bolt and the paint
mark on the cylinder head are in line.
Caution
1) If a bolt is tightened to an angle of less than 90° it has not
been tightened sufficiently.
2) If the angle of tightening exceeds the regulation level,
remove the bolt and start again from procedure number (1).



C 
Fitting the O-ring/fuel high pressure hose
1. Apply a little fresh engine oil to the O-ring.
Caution
Ensure that engine oil does not get inside the delivery pipe.
2. Without damaging the O-ring, twist the fuel high pressure hose
to fit it to the delivery pipe, making sure that it is twisted
smoothly.
3. If the hose cannot be twisted smoothly, there is a possibility that
it may be biting into the O-ring, so remove the fuel high pressure
hose, and check for any damage to the O-ring. If the O-ring is
undamaged, reinsert it into the delivery pipe and check once
more whether the hose can be turned smoothly.
4. Tighten the mounting bolts for the fuel high pressure hose to the
specified torque.
Tightening torque: 5.0 ± 1.0 N•m.
Front of engine
Procedure number (4)Procedure number (5)
paint markpaint mark

ENGINE – CYLINDER HEAD GASKET
11-19



D 
Fitting the oil return pipe gasket
Replace the gasket with a new one, and fit it to the protruded part
shown in the diagram.
Note:
For the oil return pipe gasket on the turbocharger side, there is no
direction for slotting it in.



E 
Fitting the eyebolts
Caution
When tightening the eyebolts, hold the oil pipe joint in place
with a spanner so that it does not turn round as the eyebolts
are tightened.
Protrusion

ENGINE – TIMING BELT, TIMING BELT B
11-21
10. Power steering oil pressure switch connector
11.Heat protector
12. Power steering oil pump ASSY
13. Power steering oil pump bracket
14. Idler pulley
15. Crank angle sensor16. Crankshaft sprocket
17. Crankshaft sensing blade
•Adjust the tension of the timing belt B

18. Timing belt B tensioner
19. Timing belt B
Removal guidelines
 
A


Removing the timing belt
1. Turn the crankshaft in a clockwise direction, and match up all
the timing marks until the No.1 cylinder is in the compressor top
dead centre position.
Caution
Turn the crankshaft in the normal way.
2. Remove the rubber plug from the rear cover of the timing belt,
and prepare the special tool for adjusting bolts (MD998738).
 
C






C 



C 



B 



A 
 
D






A 


B


(engine oil)
Timing marks
Timing belt
valence

ENGINE – TIMING BELT, TIMING BELT B11-22
3. Twist the special tool for adjusting bolts (MD998738) by hand
until it touches the tensioner arm.
Caution
The special tool for adjusting bolts (MD998738) can be
slowly twisted at a rate of about 30° per second but if it is
suddenly twisted the auto-tensioner rod cannot be easily
withdrawn, and this may lead to problems with twisting and
the possibility that the special tool for adjusting bolts
(MD998738) may become bent.
4. Twist the special tool for adjusting bolts (MD998738) a little, and
align the auto-tensioner rod with setting hole A, and the
tensioner cylinder with setting hole B.
5. Insert a wire or a pin into the aligned holes.
6. Remove the special tool for adjusting bolts (MD998738), and
then loosen the bolt for fitting the timing belt tensioner, and
remove the timing belt.
Caution
If a timing belt is being re-used, check and make a note of
the direction of the arrows indicating the rotational
direction (clockwise direction) on the back of the belt.
 
B


Removing the power steering oil pump ASSY
Remove the power steering oil pump ASSY from its bracket, with
the hose intact.
Note
Secure the removed power steering oil pump ASSY with string, and
put it somewhere where it will not hinder the removal or fitting of the
timing belt.
 
C


Removing the crankshaft sprocket
1. Hold the crankshaft sprocket in place using the special spanner
(MB991367) and the special pin (MB991385).
2. Remove the crankshaft sprocket.timing belt tensioner
arm
bolt for fitting the timing belt
tensioner
wire or pin
Crankshaft
sprocket

ENGINE – TIMING BELT, TIMING BELT B
11-25



C 
Fitting the crankshaft sensing blade and the
crankshaft sprocket
1. Clean, and remove any grease from the crankshaft sensing
blade, the crankshaft sprocket, and the surface of the crankshaft
to which the crankshaft sprocket will be fitted.
2. Fit the crankshaft sensing blade and the crankshaft sprocket in
the direction shown in the diagram.
3. Clean the screw hole in the crankshaft.
4. Place the washer with the larger surface side in the direction as
shown in the diagram, and fit it to the crankshaft bolt.
5. Apply a small quantity of engine oil to the top and to the screw
thread parts of the crankshaft bolt.
6. In the same way as when it was removed, hold the crankshaft
sprocket using the special tool, and tighten the crankshaft bolt to
the specified torque.
Tightening torque: 167 N·m



D 
Fitting the auto-tensioner
1. If the auto-tensioner rod remains in an extended state, install it
using the following procedure.
(1) Using a press or a vice, slowly compress the auto-
tensioner rod and align the rod with setting hole A and the
tensioner cylinder with setting hole B.
Caution
If the speed of compression is too fast, there is a
chance that the rod may break, so carry out this
operation slowly.
(2) Insert a wire or pin into the aligned holes.
Note
If a brand new or a replacement auto-tensioner is being
used, use a pin to set the auto-tensioner in place.
2. Fit the auto-tensioner into the engine and tighten the mounting
bolt to the specified torque. Do not remove the wire or pin until
the tension of the timing belt has been adjusted.
Tightening torque: 23 ± 3 N·m



E 
Fitting the tensioner pulley
As a temporary step, fit the tensioner pulley as shown in the
diagram.
Front of engine
washer
crankshaft sprocket
clean
here
crankshaft
crankshaft boltcrankshaft
sensing
blade
remove
grease
wire or pin
tensioner pulley holes

ENGINE – TIMING BELT, TIMING BELT B11-26



F 
Fitting the timing belt
1. Check that all the timing marks for the camshaft sprocket, the
crankshaft sprocket and the oil pump sprocket are aligned.
2. After the timing marks for the oil pump sprocket have been
aligned, remove the plug from the cylinder block and insert a
posidrive (+) with a diameter of 8 mm into the plug hole. Check
that more than 60 mm of the shaft of the screwdriver can be
inserted. If the screwdriver strikes the balancer shaft and can
only be inserted to a depth of 20 ~ 25 mm, turn the sprocket one
complete turn, realign the timing marks, and check that more
than 60 mm of the screwdriver can be inserted. Do not remove
the screwdriver until the timing belt has been fitted.
3. Install the timing belt in accordance with the following guidelines
so that the side that is under tension does not get slack.
(1) Fit the timing belt around the crankshaft sprocket first, then
the oil pump sprocket and then fit it around the idler pulley.
(2) Fit the timing belt around the camshaft sprocket (exhaust
side) and hold it in place with a paper clip at the position
shown in the diagram.
timing marks
camshaft
sprocket (inlet
side)
timing
marks
crankshaft
sprocket
camshaft
sprocket
(exhaust
side)
timing
marks
oil pump
sprocket
plug
more than
60 mm
screwdriver
balancer shaft
camshaft
sprocket (inlet
side)
tensioner pulley
crankshaft
sprocket
camshaft
sprocket
(exhaust side)
idler
pulley
oil pump
sprocket
paper
clip

ENGINE – TIMING BELT, TIMING BELT B, ENGINE ASSY11-28
5. Using the special wrench for the tensioner pulley socket
(MD998767) or a torque wrench, apply tension torque (3.5 N·m)
to the timing belt in the direction shown in the diagram, and
tighten the mounting bolt for the tensioner pulley to the specified
torque.
Tightening torque: 48 ± 5 N·m
Caution
When tightening the installed bolt, take care that the
tensioner pulley does not turn around with it. If the pulley
does turn around with the bolt, the tension of the belt will
become too strong.
6. Remove the wire or pin which had been inserted when the auto-
tensioner was fitted.
7. Remove by hand the special adjusting bolt (MD998738) which
had been fitted in step 1.
8. Turn the crankshaft two complete turns in a clockwise direction,
and leave it for about 15 minutes.
9. Reinsert the wire or pin which had been removed in step 6, and
check that it can be easily pulled out again.
If the wire or pin can be easily pulled out the tension of the
timing belt is just right, so the wire or pin should be removed
completely. At this point check that the auto-tensioner rod is not
projecting more than the amount specified.
Specified projection (A): 3.8 ~ 4.5 mm
10. If the wire or pin cannot be easily pulled out, repeat steps 1 to 8
until the tension of the timing belt is just right.
11.Recheck that the timing marks on all of the sprockets are in line.
Caution
If the crankshaft bolt is turned in an anti-clockwise
direction, the tightening torque of the crankshaft bolt must
be checked, and if it is loose, it must be retightened.
ENGINE ASSY
Removal and fitting
Jobs to be completed before removal and after fitting
•Measures to prevent fuel leaking.
•Check for fuel dripping.
•Removal and refitting of the bonnet.
•Removal and refitting of the strut tower bar.
•Removal and refitting of the valence. (Ref Section 51: Front bumper)
•Checking the tension of the drive belt.
•Adjustment of the axle letter cable.
•Draining and replacing the engine oil.
•Draining and replacing the coolant.
•Removal and refitting of the air cleaner.
•Removal and refitting of air pipe C.
•Removal and refitting of the battery and the battery tray.
•Removal and refitting of the centre cover. (Ref P11-5)
•Removal and refitting of the axle letter cable.
•Removal and refitting of the radiator.
•Removal and refitting of the front exhaust pipe.