interior MITSUBISHI LANCER EVOLUTION X 2008 Owner's Guide

INSIDE REAR VIEW MIRROR
TSB Revision
INTERIOR52A-17
INSIDE REAR VIEW MIRRORM1521002600561
REMOVAL SERVICE POINT
1. Disengage claw A and lower the cover in the arrow 1 direction.
2. Push claw B in the arrow 2 direction to unlock, and pull out the mirror in the arrow 3 direction.
FRONT SEAT ASSEMBLY
REMOVAL AND INSTALLATIONM1522001301165
WARNING
Before removing the front seat assembly, refer to GROUP 52B, Service Precautions P.52B-24
and Air Bag Module and Clock Spring P.52B-367.
AC209066
Claw B
Claw A
Cover
12
3
AD
AC609288AB
4
3 1
43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb 43 ± 8 N·m
32 ± 6 ft-lb
43 ± 8 N·m
32 ± 6 ft-lb
1
4
2
2
2
3
2

FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-18
REMOVAL SERVICE POINT
.
<> WIRING HARNESS CONNECTOR DISCON-
NECTION
Disconnect the following wiring harness connectors:
INSTALLATION SERVICE POINT
.
>>A<< FRONT SEAT ASSEMBLY INSTALLATION
1.Temporarily tighten the bolts in all mounting locations
shown in the illustration with no load applied to the front
seat cushion and check the operation of the seat slide.
2. Tighten the bolts in all mounti ng locations to the specified
torque.
1.Head restraint
Front seat assembly removal
steps

2.Front seat anchor cover rear
3.Front seat anchor cover front
<>•Harness connector
>>A<<4.Front seat assembly
Front seat assembly removal steps
(Continued)
Connector
numberConnector name
D-27 (4 −
black)Heated seat connector (driver's
seat)
D-28 (2 −
gray)Seat slide sensor connector
(driver's seat)
D-29 (4 −
black)Seat belt switch connector (driver's
seat)
D-30 (2 −
yellow)Side air bag module (squib)
connector (driver's seat) with side air bag>
D-32 (2 −
yellow)Side air bag module (squib)
connector (front passenger's seat)

D-33 (4 −
black)Seat belt switch connector (front
passenger's seat)
D-34 (4 −
black)Heated seat connector
(passenger's seat) heated seat>
D-35 (6)Occupant classification system
connector (passenger's seat)
AC611243
D-30 D-29
D-28D-27
AB
D-32
D-33
D-34 D-35
AC610011AB

FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-19
INSPECTIONM1522005500287
CONTINUITY TEST OF HEATED SEAT SWITCH
.1. Check for continuity between terminals.
2. Check that the indicator is lighted at HI or LO when battery voltage is supplied to terminal 5 and terminal 8 is grounded.
3. Check that indicator is lighted when battery voltage is
supplied to terminal s 2 and terminal 6.
.
SEAT CUSHION HEATER CHECK
Measure the resistance between terminals.
Standard value: At room temperature 20 °C (68 °F)
Between terminals 1 and terminal 2
Standard type: Approximately 3.82 ± 4.66 ohms
Spots type: Approximately 4.47 ± 5.48 ohms
Between terminals 1 and terminal 4
Standard type: 8.90 ± 10.88 ohms
Spots type: 8.79 ± 10.75 ohms
.
ItemSwitch
positionTester
connectionSpecified
condition
Driver's
seat sideHI1 − 5, 3 − 8Continuity
exists (2
Ω
or less)
OFF1 − 5, 3 − 5, 5
− 8
Open
circuit
LO3 − 5Continuity
exists (2
Ω
or less)
Front
passenger'
s seat sideHI4 − 5, 8 − 9Continuity
exists (2
Ω
or less)
OFF4 − 5, 5 − 8, 5
− 9
Open
circuit
LO5 − 9Continuity
exists (2
Ω
or less)
ACX00625
AC610374

FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-20
SEATBACK HEATER CHECK
Measure the resistance between terminals.
Standard value: At room temperature 20 °C (68 °F)
Standard type: 4.86 ± 5.94 ohms
Spots type: 4.06 ± 4.96 ohms
HEATED SEAT RELAY CONTINUITY CHECK
12
AC200100
Battery voltageTester
connectionSpecified
condition
Not applied3 − 4Open circuit
•Connect
terminal 1 to
the positive
battery
terminal
•Connect
terminal 2 to
the negative
battery
terminal
3 − 4Continuity
exists (2
Ω or
less)
AC610364
2
3
4
1
AB
Heated seat
relay

FRONT SEAT ASSEMBLY
TSB Revision
INTERIOR52A-21
DISASSEMBLY AND ASSEMBLYM1522001501211
Required Special Tool:
•MB990784: Ornament Remover
AC506551
AC609289AB
1
2
3
4
5
9
10
67
12
11
23 14
13
N
10
20
19N
22
21
15
8
161718
41 ± 10 N·m
30 ± 8 ft-lb41 ± 10 N·m
30 ± 8 ft-lb
Disassembly steps
<>1.Height adjuster lever cap
2.Height adjuster lever
3.Reclining adjuster cap
4.Reclining adjuster lever
5.Side shield cover
6.Inner seat belt
7.Hinge cover
8.Side shield inner cover
9.Reclining adjust er upper cover
10.Reclining adjuster cover
11 .Harness
12.Hook
13.Front seatback pad and frame
assembly
<>14.Head restraint guide
15.Hog ling
16.Front seatback cover
17.Front seatback pad
18.Front seatback frame
19.Front seat cushion assembly
20.Hog ling
21.Front seat cushion cover
22.Front seat cushion pad
23.Front seat cushion frame
Disassembly steps (Continued)