service MITSUBISHI MIRAGE 2014 6.G User Guide

3-68 Features and controls
3Service brake
N00517500318
Brake pedalOveruse of the brake can cause weakening, resulting in poor
brake response and premature wear of the brake pads.
When driving down a long or steep hill, use engine braking by
moving the selector lever to “B” (BRAKE) position.
Power brakes
N00517600436
Your vehicle is equipped with power brakes for more braking
force with less brake pedal effort.
Your brakes are designed to operate at full capacity, even if the
power assist is not being used.
If the power assist is not being used, the effort needed to press
the brake pedal is greater.
If you should lose the power assist for some reason, the brakes
will still work.
If the power brake unit or either of the two brake hydraulic sys-
tems stops working properly, the rest of the brake system will
still work, but the vehicle will not slow down as quickly.
You will know this has happened if you find you need to press
the brake down farther, or harder when slowing down or stop-
ping, or if the brake warning light and the warning display in
the multi-information display come on. Have the brake system
repaired at an authorized Mitsubishi Motors dealer or a repair
facility of your choice immediately.
WA R N I N G
!
Do not leave any objects near the brake pedal or let
a floor mat slide under it; doing so could prevent the
full pedal stroke that would be necessary in an emer-
gency. Make sure that the pedal can be operated
freely at all times. Make sure the floor mat is
securely held in place.
CAUTION
!
It is important not to drive the vehicle with your foot
resting on the brake pedal when braking is not
required. This practice can result in very high brake
temperatures, premature lining wear, and possible
damage to the brakes.
WA R N I N G
!
Never coast downhill with the engine OFF. Keep the
engine running whenever your vehicle is in motion.
If you turn off the engine while driving, the power
brake booster will stop working and your brakes
will not work as well.
If the power assist is lost or if either brake hydraulic
system stops working properly, take your vehicle to
an authorized Mitsubishi Motors dealer or a repair
facility of your choice immediately.
BK0162600US.book 68 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-69
3
Brake pad wear alarm
N00550700124
The disc brakes have an alarm that makes a metallic squeal
when the brake pads have worn down enough to need service.
If you hear this sound, have the brake pads replaced at an
authorized Mitsubishi Motors dealer or a repair facility of your
choice.
Hill start assist
(if so equipped)
N00562600087
The hill start assist makes it easy to start off on a steep uphill
slope by preventing the vehicle from moving backwards. It
keeps the braking force for about 2 second when you move
your foot from the brake pedal to the accelerator pedal.
WA R N I N G
!
Driving with worn brake pads will make it harder to
stop, and can cause an accident.
CAUTION
!
Do not overly rely on the hill start assist to prevent
backwards movement of the vehicle. Under certain
circumstances, even when hill start assist is acti-
vated, the vehicle may move backwards if the brake
pedal is not sufficiently depressed, if the vehicle is
heavily loaded, or if the road is very steep or slip-
pery.
The hill start assist is not designed to keep the vehi-
cle stopped in place on uphill slopes for more than 2
seconds.
When facing uphill, do not rely on using the hill
start assist to maintain a stopped position as an
alternative to depressing the brake pedal.
Doing so could cause an accident.
Do not perform the following operation while the
hill start assist is operating.
[Except for vehicles equipped with the F.A.S.T.-key]
Turn the ignition switch to the “OFF” or “ACC”
position.
[Vehicles equipped with the F.A.S.T.-key]
Put the operation mode in OFF or ACC. The hill
start assist could stop operating, which could result
in an accident.
BK0162600US.book 69 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-98 Features and controls
3
Tachometer
N00519200292
The tachometer shows engine revolutions per minute. This
allows the driver to determine the most efficient selector posi-
tion and engine speed combinations.
This gauge also assists in evaluating engine performance.
Multi-information display
N00555000278
The multi-information display displays the odometer, trip
odometer, service reminder, fuel remaining, selector lever posi-
tion, average fuel consumption, driving range, etc.
It is also possible to change elements such as the language and
units used on the multi-information display.NOTE
When the ignition switch or the operation mode is in OFF,
the selector lever position display and fuel remaining dis-
play are not displayed.
CAUTION
!
The red zone indicates an engine speed beyond the
range of safe operation.
Select the correct shift position (manual transaxle)
or selector position (CVT) to control the engine
speed so that the tachometer indicator does not
enter the red zone.
1- Information display → P.3-99
2- Service reminder → P.3-103
3- Selector lever position display* → P.3-64
4- Fuel remaining display → P. 3 - 1 0 2
BK0162600US.book 98 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-99
3
Information display
N00574800015
Each time you lightly press the multi-information display switch (A), the display switches in the following order.NOTE
When the ignition switch or the operation mode is in OFF, the driving range display and average fuel consumption display are
not displayed.

While driving, the service reminder is not displayed even if you operate the multi-information display switch.1- Odometer → P.3-100 5- Driving range display → P. 3 - 1 0 1
2-
Trip odometer → P.3-1006- Average fuel consumption display → P.3-102
3-
Trip odometer → P. 3 - 1 0 07- Service reminder (distance) → P.3-103
4- Instrument panel light dimmer control → P.3-100 8- Service reminder (month) → P.3-103
BK0162600US.book 99 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-103
3
Fuel remaining warning displayWhen the remaining fuel level runs low (one segment is dis-
played), the last segment of the fuel gauge flashes when the
ignition switch is turned to the “ON” position or the operation
mode is changed to ON.
When the remaining fuel level very runs low (no segments dis-
played), “ ” and the bar graph flash.
If the warning display appears, refuel as soon as possible.NOTE
On hills or curves, the display may be incorrect due to the
movement of fuel in the tank.
Service reminder
N00556700227
Displays the approximate time until the next recommended
periodic inspection. “---” is displayed when the inspection time
has arrived.NOTE
The service reminder time can be modified by an autho-
rized Mitsubishi Motors dealer, to adjust for severe usage,
etc. Refer to “Severe maintenance schedule” in your vehi-
cle’s Warranty and Maintenance Manual. For further
information, please contact your authorized Mitsubishi
Motors dealer.
1. Shows the time until the next periodic inspection.NOTE
Shows the distance in units of 100 miles (100 km) and the
time in units of 1 month.
CAUTION
!
Running out of gas could damage the catalytic con-
verter. If the warning display appears, refuel as soon
as possible.
Distance
Month
BK0162600US.book 103 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-104 Features and controls
3
2. This informs you that a periodic inspection is due. Contact
an authorized Mitsubishi Motors dealer or a repair facility
of your choice to have the system checked.
3. After your vehicle is inspected at an authorized Mitsubishi
Motors dealer, it displays the time until the next periodic
inspection.To resetThe “---” display can be reset while the ignition switch or the
operation mode is in OFF.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the service reminder display.2. Press and hold the multi-information display switch for
about 1 second or more to make the spanner mark start
flashing. (If there is no operation for about 10 seconds
with flashing, the display will revert to its original indica-
tion.)
3. With this indicator flashing, if you lightly press the multi-
information meter switch, the display switches from “---”
to “cLEAr”. After that, the time until the next periodic
inspection is shown.BK0162600US.book 104 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-108 Features and controls
3
NOTE
The display units for the driving range, the average fuel
consumption are changed, but the units for the indicating
needle (speedometer), the odometer, the trip odometer and
the service reminder will remain unchanged.

If the battery is disconnected, the memory of the unit set-
ting is erased and it returns automatically to factory set-
ting.
The distance units is also changed in the following combina-
tions to match the selected fuel consumption unit.
Fuel
consumption
Distance
(driving range)
km/L km
L/100 km km
mpg mile (s)
BK0162600US.book 108 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-109
3 Indicator and warning light package
N00519800849
1- High beam indicator → P. 3 - 1 1 0
2- Electric power steering system warning light → P.3-75
3- Tire pressure monitoring system warning light (if so
equipped) → P.3-88
4- Turn signal indicators/Hazard warning lights → P. 3 - 1 1 0
5- Front fog light indicator (if so equipped) → P. 3 - 1 1 0
6- Door-ajar warning light → P. 3 - 1 1 4
7- Supplemental Restraint System (SRS) warning light
→ P.2-44
8- High coolant temperature warning light (red) → P. 3 - 1 1 3
9- Low coolant temperature indicator (green) → P. 3 - 1 1 0
10- Oil pressure warning light → P. 3 - 1 1 3
11- Engine malfunction indicator (“SERVICE ENGINE SOON”
or “Check engine light”) → P. 3 - 1 1 212- Charging system warning light → P. 3 - 1 1 3
13- Brake warning light → P.3-111
14- Anti-lock braking system warning light → P.3-73
15- Multi-information display → P.3-98
16- Driver ’s seat belt reminder/warning light → P.2-18
17- Cruise control indicator (if so equipped) → P.3-81
18- Active stability control (ASC) indicator/warning light →
P.3-78, 3-79
19- Active stability control (ASC) OFF indicator/warning light
→ P.3-78, 3-79
20- ECO indicator → P. 3 - 1 1 0
21- For details, refer to “Warning activator” on page 3-21 (if so
equipped)
22- For details, refer to “Warning activator” on page 3-21 (if so
equipped)
BK0162600US.book 109 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-112 Features and controls
3
Engine malfunction indicator (“SERVICE
ENGINE SOON” or “Check engine light”)
N00520500804
This indicator is a part of the onboard diagnostic (OBD) sys-
tem which monitors the emissions, engine control system or
continuously variable transmission (CVT) control system. If a
problem is detected in one of these systems, this indicator illu-
minates or flashes. When the ignition switch is turned to the
“ON” position or the operation mode is put in ON, this indica-
tor normally comes on and goes off after the engine has started.
This indicator will come on if the fuel tank filler cap is not
properly tightened. If this indicator comes on and stays on after
refueling, stop the engine and check that the cap is properly
tightened. (Turn the cap clockwise until you hear clicking
sounds.)
If this indicator does not go off after several seconds or lights
up while driving, have the system checked as soon as possible
at an authorized Mitsubishi Motors dealer or a repair facility of
your choice.
NOTE
Do not disconnect the battery cable when the engine mal-
function indicator (“SERVICE ENGINE SOON” or
“Check engine light”) is on.
The engine electronic control module stores critical OBD
information (especially exhaust emission data), which
may be lost if the battery cable is disconnected while the
engine malfunction indicator is on. This will make it diffi-
cult to diagnose the cause of future problems.
CAUTION
!
Driving for a long time with the engine malfunction
indicator on may cause more damage to the emission
control system. This could also affect fuel economy
and drivability.
If this indicator does not come on when the ignition
switch is turned to the “ON” position or the opera-
tion mode is put in ON, have the system checked at
an authorized Mitsubishi Motors dealer or a repair
facility of your choice.

If the engine malfunction indicator comes on while
the engine is running, avoid driving at high speeds.
During vehicle operation with the indicator on, the
vehicle may not accelerate when you depress the
accelerator pedal.
When the vehicle is stationary with the indicator on,
you must depress the brake pedal more firmly than
usual since the engine idling speed is higher than
usual and a vehicle with a CVT has a stronger ten-
dency to creep forward.
CAUTION
!
BK0162600US.book 112 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-128 Features and controls
3Bluetooth
® 2.0 interface
(if so equipped)
N00563900162
The Bluetooth
® 2.0 interface allows for making/receiving
hands-free calls in the vehicle using a cellular phone compati-
ble with a wireless communication technology commonly
known as Bluetooth
®. It also allows the user to play music,
saved in a Bluetooth® music player, through the vehicle’s
speakers.
The system is equipped with a voice recognition function,
which allows you to make hands-free calls by simple switch
and voice command operations using a defined voice tree.
The Bluetooth
® 2.0 interface can be used when the ignition
switch or the operation mode is in ON or ACC.
Before you can use the Bluetooth
® 2.0 interface, you must pair
the Bluetooth
® device and Bluetooth
® 2.0 interface. Refer to
“Connecting the Bluetooth
® 2.0 interface and Bluetooth
®
device” on page 3-135.
Bluetooth
® is a registered trademark of BLUETOOTH SIG,
INC.
NOTE
The Bluetooth
® 2.0 interface cannot be used if the
Bluetooth
® device has a dead battery or the device power
is turned off.

Hands-free calls will not be possible if your phone does
not have service available.

If you place the Bluetooth
® device in the cargo area, you
may not be able to use the Bluetooth
® 2.0 interface.

Some Bluetooth
® devices are not compatible with the
Bluetooth
® 2.0 interface.

You can confirm the Link System software version by
pressing the HANG-UP button 3 times (press and hold 2
times and then press briefly) within 10 seconds.
WA R N I N G
!
Although the Bluetooth
® 2.0 interface allows you to
make hands-free calls, if you choose to use the cellu-
lar phone while driving, you must not allow yourself
to be distracted from the safe operation of your vehi-
cle. Anything, including cellular phone usage, that
distracts you from the safe operation of your vehicle
increases your risk of an accident.

Refer to and comply with all state and local laws in
your area regarding cellular phone usage while driv-
ing.
BK0162600US.book 128 ページ ２０１３年３月２２日　金曜日　午後２時４１分