ignition MITSUBISHI MIRAGE 2014 6.G Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2014, Model line: MIRAGE, Model: MITSUBISHI MIRAGE 2014 6.GPages: 460, PDF Size: 20.86 MB
Page 181 of 460
Features and controls
3-93
3 Rear-view camera
(if so equipped)
N00546200144
When the gearshift lever or the selector lever is in the “R” posi-
tion with the ignition switch or the operation mode is in ON,
the rear-view image will be displayed on the screen of the
Mitsubishi Multi Entertainment System.
When the gearshift lever or the selector lever is shifted out of
the “R” position, the rear-view image will go off.
Location of rear-view cameraThe rear-view camera (A) is in the liftgate, at the left side of
the liftgate handle.
WA R N I N G
!Never rely solely on the rear-view camera to clear
the area behind your vehicle. Always check visually
behind and all around your vehicle for persons, ani-
mals, obstructions or other vehicles. Failure to do so
can result in vehicle damage, serious injury or
death.The rear-view camera is an aid system for backing
up, but it is not a substitute for your visual confir-
mation.The view on the screen is limited, and objects out-
side the view, such as under the bumper or around
either corner of the bumper end, cannot be seen on
the screen.
CAUTION
!If the camera lens gets dirty, a clear image cannot be
obtained. As necessary, rinse the lens with clean
water and gently wipe with a clean, soft cloth.To avoid damaging the camera;
• Do not rub the cover excessively or polish it by
using an abrasive compound.
• Do not disassemble the camera.
• Do not splash hot water directly on the lens.
• Do not spray the camera and its surroundings with
high-pressure water.
• Make sure that the liftgate is securely closed when
backing up.
BK0162600US.book 93 ページ ２０１３年３月２２日 金曜日 午後２時４１分
Page 186 of 460
3-98 Features and controls
3
Tachometer
N00519200292
The tachometer shows engine revolutions per minute. This
allows the driver to determine the most efficient selector posi-
tion and engine speed combinations.
This gauge also assists in evaluating engine performance.
Multi-information display
N00555000278
The multi-information display displays the odometer, trip
odometer, service reminder, fuel remaining, selector lever posi-
tion, average fuel consumption, driving range, etc.
It is also possible to change elements such as the language and
units used on the multi-information display.NOTEWhen the ignition switch or the operation mode is in OFF,
the selector lever position display and fuel remaining dis-
play are not displayed.
CAUTION
!The red zone indicates an engine speed beyond the
range of safe operation.
Select the correct shift position (manual transaxle)
or selector position (CVT) to control the engine
speed so that the tachometer indicator does not
enter the red zone.
1- Information display → P.3-99
2- Service reminder → P.3-103
3- Selector lever position display* → P.3-64
4- Fuel remaining display → P. 3 - 1 0 2
BK0162600US.book 98 ページ ２０１３年３月２２日 金曜日 午後２時４１分
Page 187 of 460
Features and controls
3-99
3
Information display
N00574800015
Each time you lightly press the multi-information display switch (A), the display switches in the following order.NOTEWhen the ignition switch or the operation mode is in OFF, the driving range display and average fuel consumption display are
not displayed.
While driving, the service reminder is not displayed even if you operate the multi-information display switch.1- Odometer → P.3-100 5- Driving range display → P. 3 - 1 0 1
2-
Trip odometer → P.3-1006- Average fuel consumption display → P.3-102
3-
Trip odometer → P. 3 - 1 0 07- Service reminder (distance) → P.3-103
4- Instrument panel light dimmer control → P.3-100 8- Service reminder (month) → P.3-103
BK0162600US.book 99 ページ ２０１３年３月２２日 金曜日 午後２時４１分
Page 189 of 460
Features and controls
3-101
3
NOTEYou can adjust to 8 different levels for when the parking
lights or headlights are illuminated and 8 for when they
are not.
Each time you reduce two brightness levels, the segment
display of the brightness level decreases one by one.
If you press and hold the switch for longer than about 1
second, the brightness automatically scrolls through its
different levels, and stops scrolling when you release the
switch. Select your desired level of brightness.
The brightness level of the instruments is stored when the
ignition switch is turned to the “OFF” position or the
operation mode is put in OFF.
Driving range display
N00575200016
This displays the approximate driving range (how many more
miles or kilometers you can drive). When the driving range
falls below approximately 30 miles (50 km), “---” is displayed.NOTEThe driving range is determined based on the fuel con-
sumption data. This may vary depending on the driving
conditions and habits. Treat the distance displayed as just
a rough guideline.
When you refuel, the driving range display is updated.
However, if you only add a small amount of fuel, the cor-
rect value will not be displayed. Fill to a full tank when-
ever possible.
When your vehicle is stopped on an extremely steep hill,
the driving range value may, change. This is due to the
movement of fuel in the tank and does not indicate any
breakdown.
The display setting can be changed to the preferred units
(miles or km).
Refer to “Changing the function settings” on page 3-105.
BK0162600US.book 101 ページ ２０１３年３月２２日 金曜日 午後２時４１分
Page 190 of 460
3-102 Features and controls
3
Average fuel consumption display
N00575300017
This displays the average fuel consumption from the last reset
to the present.
The reset mode conditions for the average fuel consumption
display can be switched between “Auto reset” and “Manual
reset”.
For information on how to change the average fuel consump-
tion display setting, refer to “Changing the function settings”
on page 3-105.NOTEThe average fuel consumption display can be reset sepa-
rately in both auto reset mode and manual reset mode.
“---” is displayed when the average fuel consumption can-
not be measured.
The initial (default) setting is “Auto reset mode”.
Average fuel consumption may vary depend on the driv-
ing conditions (road conditions, how you drive, etc.).
The actual fuel consumption may differ from the fuel con-
sumption displayed, so treat the fuel consumption dis-
played as just a rough guideline.
Disconnecting the battery cable will erase from memory
the manual reset mode or auto reset mode setting for the
average fuel consumption display.
The display setting can be changed to the preferred units
{mpg, km/L, L/100 km}.
Refer to “Changing the function settings” on page 3-105.
Fuel remaining display
N00575400018
The fuel remaining display indicates the fuel level in the fuel
tank when the ignition switch or the operation mode in ON.NOTEIt may take several seconds to stabilize the display after
refilling the tank.
If fuel is added with the ignition switch or the operation
mode in ON, the remaining fuel display may incorrectly
indicate the fuel level.
The fuel lid mark (A) indicates that the fuel tank filler
door is located on the left side of the vehicle. (Refer to
“Filling the fuel tank” on page 1-4.)1- Full
0- Empty
BK0162600US.book 102 ページ ２０１３年３月２２日 金曜日 午後２時４１分
Page 191 of 460
Features and controls
3-103
3
Fuel remaining warning displayWhen the remaining fuel level runs low (one segment is dis-
played), the last segment of the fuel gauge flashes when the
ignition switch is turned to the “ON” position or the operation
mode is changed to ON.
When the remaining fuel level very runs low (no segments dis-
played), “ ” and the bar graph flash.
If the warning display appears, refuel as soon as possible.NOTEOn hills or curves, the display may be incorrect due to the
movement of fuel in the tank.
Service reminder
N00556700227
Displays the approximate time until the next recommended
periodic inspection. “---” is displayed when the inspection time
has arrived.NOTEThe service reminder time can be modified by an autho-
rized Mitsubishi Motors dealer, to adjust for severe usage,
etc. Refer to “Severe maintenance schedule” in your vehi-
cle’s Warranty and Maintenance Manual. For further
information, please contact your authorized Mitsubishi
Motors dealer.
1. Shows the time until the next periodic inspection.NOTEShows the distance in units of 100 miles (100 km) and the
time in units of 1 month.
CAUTION
!Running out of gas could damage the catalytic con-
verter. If the warning display appears, refuel as soon
as possible.
Distance
Month
BK0162600US.book 103 ページ ２０１３年３月２２日 金曜日 午後２時４１分
Page 192 of 460
3-104 Features and controls
3
2. This informs you that a periodic inspection is due. Contact
an authorized Mitsubishi Motors dealer or a repair facility
of your choice to have the system checked.
3. After your vehicle is inspected at an authorized Mitsubishi
Motors dealer, it displays the time until the next periodic
inspection.To resetThe “---” display can be reset while the ignition switch or the
operation mode is in OFF.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the service reminder display.2. Press and hold the multi-information display switch for
about 1 second or more to make the spanner mark start
flashing. (If there is no operation for about 10 seconds
with flashing, the display will revert to its original indica-
tion.)
3. With this indicator flashing, if you lightly press the multi-
information meter switch, the display switches from “---”
to “cLEAr”. After that, the time until the next periodic
inspection is shown.BK0162600US.book 104 ページ ２０１３年３月２２日 金曜日 午後２時４１分
Page 193 of 460
Features and controls
3-105
3
NOTEThe “---” display cannot be reset while the ignition switch
or the operation mode is in ON.
When “---” is displayed, after a certain distance and a cer-
tain period of time, the display is reset and the time until
the next periodic inspection is displayed.
If you accidentally reset the display, consult an authorized
Mitsubishi Motors dealer for assistance.
Changing the function settings
N00556800143
When the ignition switch or the operation mode is in ON, the
fuel consumption unit, displayed in the multi-information dis-
play, and the average fuel consumption reset mode can be mod-
ified as desired.Changing the reset mode for average fuel consumption
N00575500019
You can change the mode condition for the average fuel con-
sumption display to “Auto reset” or “Manual reset”.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the driving range display.
Refer to “Information display” on page 3-99.
CAUTION
!The customer is responsible for making sure that
regular inspections and maintenance and periodic
inspections and maintenance are performed.
Inspections and maintenance must be performed to
prevent accidents and malfunctions.
CAUTION
!The driver should not operate the display while the
vehicle is in motion.When operating the system, stop the vehicle in a safe
area.
BK0162600US.book 105 ページ ２０１３年３月２２日 金曜日 午後２時４１分
Page 194 of 460
3-106 Features and controls
3
2. Each time you press the multi-information display switch
for 1 second or more on driving range display, you can
switch reset mode for average fuel consumption.
(A: Auto reset mode, B: Manual reset mode)Manual reset mode
When the average fuel consumption is being displayed, if
you hold down the multi-information display switch,
these calculations will be reset to zero.
When the following operation is performed, the mode set-
ting changes automatically from manual to auto.
[Except for vehicles equipped with the F.A.S.T.-key]
Turn the ignition switch to the “ON” position from the
“ACC” or “OFF” position.
[For vehicles equipped with the F.A.S.T.-key]
Change the operation mode to ON from ACC or OFF.
Auto reset mode Manual reset mode
BK0162600US.book 106 ページ ２０１３年３月２２日 金曜日 午後２時４１分
Page 195 of 460
Features and controls
3-107
3
Auto reset mode
When the average fuel consumption is being displayed, if
you hold down the multi-information display switch,
these calculations will be reset to zero.
When the engine switch or the operation mode is in the
following conditions, the average fuel consumption dis-
play will automatically reset.
[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch has been set to the “ACC” or “OFF”
position for about 4 hours or more.
[For vehicles equipped with the F.A.S.T.-key]
The operation mode has been set to ACC or OFF for about
4 hours or more.NOTEThe average fuel consumption display can be reset sepa-
rately for the auto reset mode and for the manual reset
mode.
Disconnecting the battery cable will erase from memory
the manual reset mode or auto reset mode setting for the
average fuel consumption display.
The initial (default) setting is “Auto reset mode”.
Changing the fuel consumption display unit
N00557100156
The fuel consumption display unit can be changed. The dis-
tance and amount units are also switched to match the selected
fuel consumption unit.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the average fuel consumption display.
Refer to “Information display” on page 3-99.
2. Press and hold the multi-information display switch for
about 5 seconds or more until buzzer sound is heard twice.
3. Press and hold the multi-information display switch to
switch in sequence from “km/L” → “L/100 km” →
“mpg” → “km/L”.
BK0162600US.book 107 ページ ２０１３年３月２２日 金曜日 午後２時４１分