ignition MITSUBISHI MIRAGE 2014 6.G Repair Manual

3-128 Features and controls
3Bluetooth
® 2.0 interface
(if so equipped)
N00563900162
The Bluetooth
® 2.0 interface allows for making/receiving
hands-free calls in the vehicle using a cellular phone compati-
ble with a wireless communication technology commonly
known as Bluetooth
®. It also allows the user to play music,
saved in a Bluetooth® music player, through the vehicle’s
speakers.
The system is equipped with a voice recognition function,
which allows you to make hands-free calls by simple switch
and voice command operations using a defined voice tree.
The Bluetooth
® 2.0 interface can be used when the ignition
switch or the operation mode is in ON or ACC.
Before you can use the Bluetooth
® 2.0 interface, you must pair
the Bluetooth
® device and Bluetooth
® 2.0 interface. Refer to
“Connecting the Bluetooth
® 2.0 interface and Bluetooth
®
device” on page 3-135.
Bluetooth
® is a registered trademark of BLUETOOTH SIG,
INC.
NOTE
The Bluetooth
® 2.0 interface cannot be used if the
Bluetooth
® device has a dead battery or the device power
is turned off.

Hands-free calls will not be possible if your phone does
not have service available.

If you place the Bluetooth
® device in the cargo area, you
may not be able to use the Bluetooth
® 2.0 interface.

Some Bluetooth
® devices are not compatible with the
Bluetooth
® 2.0 interface.

You can confirm the Link System software version by
pressing the HANG-UP button 3 times (press and hold 2
times and then press briefly) within 10 seconds.
WA R N I N G
!
Although the Bluetooth
® 2.0 interface allows you to
make hands-free calls, if you choose to use the cellu-
lar phone while driving, you must not allow yourself
to be distracted from the safe operation of your vehi-
cle. Anything, including cellular phone usage, that
distracts you from the safe operation of your vehicle
increases your risk of an accident.

Refer to and comply with all state and local laws in
your area regarding cellular phone usage while driv-
ing.
BK0162600US.book 128 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-133
3
Setting the passcode
Use the following procedure to turn on the security function by
setting a passcode.
1. Press the SPEECH button.
2. Say “Setup.”
3. Say “Passcode.”
4. The voice guide will say “Passcode is disabled. Would
you like to enable it?” Answer “Yes.”
Answer “No” to cancel the setting of the passcode and
return to the main menu.
5. The voice guide will say “Please say a 4-digit passcode.
Remember this passcode. It will be required to use this
system.”
Say a 4-digit number which you want to set as a passcode.
6. For confirmation purposes, the voice guide will say “Pass-
code <4-digit passcode>. Is this correct?” Answer “Yes.”
Answer “No” to return to the passcode input in Step 5.
7. When the registration of the passcode is completed, the
voice guide will say “Passcode is enabled” and the system
will return to the main menu. NOTE
Passcode will be required to access the system after the
next ignition cycle.

It is required for a little time after engine stop that the
entered passcode is actually recorded in the system.
If the ignition switch or the operation mode is made to
ACC or ON or the engine is started immediately after
engine stop, there is a case when the entered passcode is
not recorded in the system. At this time, please try to enter
the passcode again.Entering the passcode
If a passcode has been set and the security function is enabled,
the voice guide will say “Hands-free system is locked. State the
passcode to continue” when the SPEECH button is pressed to
enter voice recognition mode. Say the 4-digit passcode number
to enter the passcode.
If the entered passcode is wrong, the voice guide will say “<4-
digit passcode>, Incorrect passcode. Please try again.” Enter
the correct passcode.
NOTE
You can reenter the passcode as many times as you want.

If you have forgotten your passcode, say “Cancel” to quit
the voice input mode and then check with an authorized
Mitsubishi Motors dealer.
Disabling the passcode
Use the following procedure to turn off the security function by
disabling the passcode. NOTE
System must be unlocked to disable the passcode.
1. Press the SPEECH button.
2. Say “Setup.”
3. Say “Passcode.”
4. The voice guide will say “Passcode is enabled. Would you
like to disable it?” Answer “Yes.”
Answer “No” to cancel the disabling of the passcode and
return to the main menu.
5. When the disabling of the passcode is completed, the
voice guide will say “Passcode is disabled” and the sys-
tem will return to the main menu.
BK0162600US.book 133 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-143
3
6. The voice guide will say “Calling ”
and then the system will dial the telephone number.NOTE
When the confirmation function is on, the system will
check if the name and location of the receiver are correct.
If the name is correct, answer “Yes.”
To change the name or location to call, answer “No.” The
system will return to Step 3.
Redialing
You can redial the last number called, based on the history of
dialed calls in the paired cellular phone.
Use the following procedure to redial.
1. Press the SPEECH button.
2. Say “Redial.”Send function
N00565700018
During a call, press the SPEECH button to enter voice recogni-
tion mode, then say “ SEND” to generate DTMF
tones.
For example, if during a call you need to simulate the pressing
of a phone button as a response to an automated system, press
the SPEECH button and speak “1 2 3 4 pound send” and the
1234# will be sent via your cellular phone.
Receiving calls
N00565800035
If an incoming phone call is received while the ignition switch
or the operation mode is in ON or ACC, the audio system will
be automatically turned on and switched to the incoming call,
even when the audio system was originally off.
The voice guide announcement for the incoming call will be
output from the front passenger’s seat speaker.
If the CD player or radio was playing when the incoming call
was received, the audio system will mute the sound from the
CD player or radio and output only the incoming call.
To receive the call, press the PICK-UP button on the steering
wheel control switch.
When the call is over, the audio system will return to its previ-
ous state.
BK0162600US.book 143 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-154 Features and controls
3
How to connect a USB memory device
N00566800104
To connect1. Park your vehicle in a safe place and turn the ignition
switch to the “OFF” position or put the operation mode in
OFF.
2. Open the glove compartment and remove the connector
cable (A, B) from clips (C).3. Connect a commercially available USB connector cable
(D) to the USB memory device (E).
BK0162600US.book 154 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-155
3
4. Connect the commercially available USB connector cable
(D) to the vehicle’s connector cable (B).
Be sure to hold the terminal part (A) of the connector
cable as shown in the illustration.
5. Fix the connector cable (A, B) on the clips.
NOTE
Do not connect the USB memory device to the vehicle’s
connector cable directly.
The USB memory device may be damaged.

When closing the glove compartment, be careful not to
trap the connector cable and USB memory device.To r e m o v e1. Turn the ignition switch to the “OFF” position or put the
operation mode in OFF.
2. Remove the commercially available USB connector cable
(D).
Be sure to hold the terminal part (A) of the connector
cable as shown in the illustration.
3. Fix the connector cable on the clips and close the glove
compartment.
WA R N I N G
!
An open glove compartment door can cause a seri-
ous injury or death to the front passenger in an acci-
dent, even if the passenger is wearing his/her seat
belt. Always keep the glove compartment door
closed when driving.
BK0162600US.book 155 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-156 Features and controls
3
How to connect an iPod
N00566900091
To connect1. Park your vehicle in a safe place and turn the ignition
switch to the “OFF” position or put the operation mode in
OFF.
2. Open the glove compartment and remove the connector
cable (A, B) from clips (C).3. Connect the Dock connector (D) to the iPod (E).
NOTE
Use a genuine Dock connector from Apple Inc.
On vehicles equipped with Mitsubishi Multi Entertain-
ment System (MMES), refer to the separate “Mitsubishi
Multi Entertainment System owner’s manual” for details
of connection.
BK0162600US.book 156 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-157
3
4. Connect the Dock connector (D) to the connector cable
(B).
Be sure to hold the terminal part (A) of the connector
cable as shown in the illustration.
5. Fix the connector cable (A, B) on the clips.
NOTE
When closing the glove compartment, be careful not to
trap the connector cable and iPod.To r e m o v e1. Turn the ignition switch to the “OFF” position or put the
operation mode in OFF.
2. Remove the Dock connector (D).
Be sure to hold the terminal part (A) of the connector
cable as shown in the illustration.
3. Fix the connector cable on the clips and close the glove
compartment.
WA R N I N G
!
An open glove compartment door can cause a seri-
ous injury or death to the front passenger in an acci-
dent, even if the passenger is wearing his/her seat
belt. Always keep the glove compartment door
closed when driving.
BK0162600US.book 157 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-158 Features and controls
3
Types of connectable devices and supported file
specifications
N00567000015
Device types
N00567100117
Devices of the following types can be connected.
*: “iPod,” “iPod classic,” “iPod nano,” “iPod touch” and
“iPhone” are registered trademarks of Apple Inc. in the United
States and other countries.
NOTE
Depending on the type of the USB memory device or
other device connected, the connected device may not
function properly or the available functions may be lim-
ited.

It is recommended to use an iPod with firmware updated
to the latest version.

You can charge your iPod by connecting it to the USB
input terminal when the ignition switch or the operation
mode is in ON or ACC.

Do not keep your USB memory device or iPod in your
vehicle.

It is recommended that you back up the files in case of
data damage.
Model name
Condition
USB memory deviceStorage capacity of 256
Mbytes or more
iPod* fifth generation F/W Ver.1.3 or later
iPod classic*80GB/180GB F/W Ver.1.1.2 or later
120GB F/W Ver.2.0.1 or later
160GB (late 2009) F/W Ver.2.0.4 or later
iPod nano*first generation F/W Ver.1.3.1 or later
second generation F/W Ver.1.1.3 or later
third generation F/W Ver.1.1.3 or later
fourth generation F/W Ver.1.0.4 or later
fifth generation F/W Ver.1.0.2 or later
sixth generation F/W Ver.1.0 or later
iPod touch*first generation F/W Ver.3.1.3 or later
second generation F/W Ver.4.2.1 or later
third generation F/W Ver.4.3.1 or later
fourth generation F/W Ver.4.3.1 or later
iPhone*iPhone F/W Ver.3.1.3 or later
iPhone 3G F/W Ver.4.2.1 or later
iPhone 3GS F/W Ver.4.3.1 or later
iPhone 4 F/W Ver.4.3.1 or later
iPhone 4S F/W Ver.5.0.1 or later
Models other than USB memory
devices and iPodsDigital audio player sup-
porting mass storage classModel name
Condition
BK0162600US.book 158 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-159
3

Do not connect to the USB input terminal any device
(hard disk, card reader, memory reader, etc.) other than
the connectable devices specified in the previous section.
The device and/or data may be damaged. If any of these
devices was connected by mistake, remove it after turning
the ignition switch to the “OFF” position or putting the
operation mode in OFF.
File specifications
N00567200020
You can play music files of the following specifications that
are saved in a USB memory device or other device supporting
mass storage class. When you connect your iPod, playable file
specifications depend on the connected iPod.Item
Condition
File format MP3, WMA, AAC
Maximum number of levels
(including the root)Level 8
Number of folders 700
Number of files 65,535
BK0162600US.book 159 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-161
3
Card holderCards can be slipped into the holder (A) on the sun visor.
12 V power outlets
N00525000615
Accessories can be operated while the ignition switch or the
operation mode is in ON or ACC.
To use a “plug-in” type accessory, open the cover, and insert
the plug in the power outlet.
CAUTION
!
Be sure to use a “plug-in” type accessory operating
at 12 V and at 120 W or less.
Also be aware that using electronic equipment with
the engine off may run the battery down.
When the power outlet is not in use, be sure to close
the power outlet cover. This will prevent the power
outlet from becoming clogged and short circuiting.
BK0162600US.book 161 ページ ２０１３年３月２２日　金曜日　午後２時４１分