MITSUBISHI MONTERO 1991 Service Manual
Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 1241 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Brakes dragging See BRAKES article \
\
\
\
\
\](/img/19/57332/w960_57332-1240.png "MITSUBISHI MONTERO 1991 Service Manual Brakes dragging See BRAKES article \
\
\
\
\
\")
Brakes dragging See BRAKES article \
\
\
\
\
\
\
Instability Low or uneven tire Inflate to proper
pressure pressure
Loose or worn wheel See FRONT SUSPENSION
bearings article
Loose or worn idler arm See FRONT SUSPENSION
bushing article
Loose or worn strut See FRONT SUSPENSION
bushings article
Incorrect front wheel See WHEEL ALIGNMENT
alignment article
Steering gear not See MANUAL STEERING
centered GEARS article
Springs or shock Check and replace if
necessary
Improper cross shaft See MANUAL STEERING
GEARS article
\
\
\
\
\
\
\
POWER STEERING TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC POWER STEERING TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Rattle or Pressure hoses touching Adjust to proper
Chucking Noise engine parts clearance
Loose Pitman shaft Adjust or replace if
necessary
Tie rods ends or Pitman Tighten and check system
arm loose
Rack and pinion mounts Tighten all mounting
loose bolts
Free play in worm and See POWER STEERING GEAR
article
Loose sector shaft or See POWER STEERING GEAR
thrust bearing adjustment
Free play in pot coupling See STEERING COLUMN
article
Page 1242 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Worn shaft serrations See STEERING COLUMN
article
\
\
\
\](/img/19/57332/w960_57332-1241.png "MITSUBISHI MONTERO 1991 Service Manual Worn shaft serrations See STEERING COLUMN
article
\
\
\
\")
Worn shaft serrations See STEERING COLUMN
article
\
\
\
\
\
\
\
Growl in Excessive pressure in Restricted hoses, see
Steering Pump hoses POWER STEERING GEAR
article
Scored pressure plates See POWER STEERING GEAR
article
Scored thrust plates or See POWER STEERING GEAR
rotor article
Extreme wear of cam ring See POWER STEERING GEAR
article
\
\
\
\
\
\
\
Rattle in Vanes not installed See POWER STEERING PUMP
Steering Pump article
Vanes sticking in rotor See POWER STEERING PUMP
article
\
\
\
\
\
\
\
Swish noise in Defective flow control See POWER STEERING PUMP
Pump valve article
\
\
\
\
\
\
\
Groan in Air in fluid See POWER STEERING PUMP
Steering Pump article
Poor pressure hose Tighten and check,
connection replace if necessary
\
\
\
\
\
\
\
Squawk When Damper "O" ring on valve See POWER STEERING PUMP
Turning spool cut article
\
\
\
\
\
\
\
Moan or Whine Pump shaft bearing scored Replace bearing and
in Pump fluid
Air in fluid or fluid See POWER STEERING PUMP
level low article
Hose or column grounded Check and replace if
necessary
Cover "O" ring missing See POWER STEERING PUMP
or damaged article
Valve cover baffle See POWER STEERING PUMP
missing or damaged article
Interference of See POWER STEERING PUMP
components in pump article
Loose or poor bracket Correct or replace if
alignment necessary
\
\
\
\
\
\
\
Hissing When Internal leakage in Check valved assembly
Parking steering gear first
\
\
\
\
\
\
\
Chirp in Loose or worn power Adjust or replace if
Steering Pump steering belt necessary
\
\
\
\
\
\
\
Buzzing When Noisy pump See POWER STEERING PUMP
Not Steering article
Page 1243 of 1333
Free play in steering See STEERING COLUMN
shaft bearing article
Bearing loose on shaft See STEERING COLUMN
serrations article
\
\
\
\
\
\
\
Clicking Noise Pump slippers too long See POWER STEERING PUMP
in Pump article
Broken slipper springs See POWER STEERING PUMP
article
Excessive wear or nicked See POWER STEERING PUMP
rotors article
Damaged cam contour See POWER STEERING PUMP
article
\
\
\
\
\
\
\
Poor Return of Wheel rubbing against See STEERING COLUMN
Wheel turn signal SWITCHES article
Flange rubbing steering See STEERING COLUMN
gear adjuster article
Tight or frozen steering See STEERING COLUMN
shaft bearing article
Steering gear out of See POWER STEERING GEAR
adjustment article
Sticking or plugged See POWER STEERING PUMP
spool valve article
Improper front end See WHEEL ALIGNMENT
alignment article
Wheel bearings worn or See FRONT SUSPENSION
loose article
Ties rods or ball joints Check and replace if
binding necessary
Intermediate shaft joints See STEERING COLUMN
binding article
Kinked pressure hoses Correct or replace if
necessary
Loose housing head See POWER STEERING GEAR
spanner nut article
Damaged valve lever See POWER STEERING GEAR
article
Sector shaft adjusted See ADJUSTMENTS in POWER
too tight STEERING GEAR article
Worm thrust bearing See ADJUSTMENTS in POWER
adjusted too tight STEERING GEAR article
Reaction ring sticking See POWER STEERING GEAR
in cylinder article
Page 1244 of 1333
Reaction ring sticking See POWER STEERING GEAR
in housing head article
Steering pump internal See POWER STEERING PUMP
leakage article
Steering gear-to-column See STEERING COLUMN
misalignment article
Lack of lubrication in Service front suspension
linkage
Lack of lubrication in Service front suspension
ball joints
\
\
\
\
\
\
\
Increased Effort High internal pump leakage See POWER STEERING PUMP
When Turning article
Wheel Fast Power steering pump belt Adjust or replace if
Foaming, Milky slipping necessary
Power Steering
Fluid, Low Fluid Low fluid level Check and fill to
Level or Low proper level
Pressure
Engine idle speed to low Adjust to correct
setting
Air in pump fluid system See POWER STEERING PUMP
article
Pump output low See POWER STEERING PUMP
article
Steering gear See POWER STEERING GEAR
malfunctioning article
\
\
\
\
\
\
\
Wheel Surges Low fluid level Check and fill to proper
or Jerks level
Loose fan belt Adjust or replace if
necessary
Insufficient pump See POWER STEERING PUMP
pressure article
Sticky flow control valve See POWER STEERING PUMP
article
Linkage hitting oil pan Replace bent components
at full turn
\
\
\
\
\
\
\
Kick Back or Air in pump fluid system See POWER STEERING PUMP
Free Play article
Worn poppet valve in See POWER STEERING PUMP
steering gear article
Excessive over center See POWER STEERING GEAR
lash article
Thrust bearing out of See POWER STEERING GEAR
adjustment article
Page 1245 of 1333
Free play in pot coupling See POWER STEERING PUMP
article
Steering gear coupling See POWER STEERING PUMP
loose on shaft article
Steering disc mounting Tighten or replace if
bolts loose necessary
Coupling loose on worm Tighten or replace if
shaft necessary
Improper sector shaft See POWER STEERING GEAR
adjustment article
Excessive worm piston See POWER STEERING GEAR
side play article
Damaged valve lever See POWER STEERING GEAR
article
Universal joint loose Tighten or replace if
necessary
Defective rotary valve See POWER STEERING GEAR
article
\
\
\
\
\
\
\
No Power When Sticking flow control See POWER STEERING PUMP
Parking valve article
Insufficient pump See POWER STEERING PUMP
pressure output article
Excessive internal pump See POWER STEERING PUMP
leakage article
Excessive internal gear See POWER STEERING PUMP
leakage article
Flange rubs against gear See STEERING COLUMN
adjust plug article
Loose pump belt Adjust or replace if
necessary
Low fluid level Check and add proper
amount of fluid
Engine idle too low Adjust to correct
setting
Steering gear-to-column See STEERING COLUMN
misaligned article
\
\
\
\
\
\
\
No Power, Left turn reaction seal See POWER STEERING GEAR
Left Turn "O" ring worn article
Left turn reaction seal See POWER STEERING GEAR
damaged/missing article
Cylinder head "O" ring See POWER STEERING PUMP
damaged article
\
\
\
\
\
\
\
Page 1246 of 1333
No Power, Column pot coupling See STEERING COLUMN
Right Turns bottomed article
Right turn reaction seal See POWER STEERING GEAR
"O" ring worn article
Right turn reaction seal See POWER STEERING GEAR
damaged article
Internal leakage through See POWER STEERING GEAR
piston end plug article
Internal leakage through See POWER STEERING GEAR
side plugs article
\
\
\
\
\
\
\
Lack of Effort Left and/or right Replace, see POWER
in Turning reaction seal sticking STEERING GEAR article
in cylinder head
\
\
\
\
\
\
\
Wanders to One Front end alignment See WHEEL ALIGNMENT
Side incorrect article
Unbalanced steering See POWER STEERING GEAR
gear valve article
\
\
\
\
\
\
\
Low Pressure Due Flow control valve stuck See POWER STEERING PUMP
to Steering Pump or inoperative article
Pressure plate not flat See POWER STEERING PUMP
against cam ring article
Extreme wear of cam ring Replace and check
adjustments
Scored plate, thrust See POWER STEERING PUMP
plate or rotor article
Vanes not installed See POWER STEERING PUMP
properly article
Vanes sticking in rotor See POWER STEERING PUMP
slots article
Cracked/broken thrust or See POWER STEERING PUMP
pressure plate article
\
\
\
\
\
\
\
STEERING COLUMN TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC STEERING COLUMN TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Noise in Coupling pulled apart See STEERING COLUMNS
Steering article
Page 1247 of 1333
Column not correctly See STEERING COLUMNS
aligned article
Broken lower joint Replace joint
Horn contact ring not See STEERING COLUMN
article
Bearing not lubricated See STEERING COLUMN
article
Shaft snap ring not Reseat or replace snap
properly seated ring
Plastic spherical joint See STEERING COLUMN
not lubricated article
Shroud or housing loose Tighten holding screws
Lock plate retaining See STEERING COLUMN
ring not seated article
Loose sight shield Tighten holding screws
\
\
\
\
\
\
\
High Steering Column assembly See STEERING COLUMN
Shaft Effort misaligned article
Improperly installed dust Adjust or replace
shield
Tight steering universal See STEERING COLUMN
joint article
\
\
\
\
\
\
\
High Shift Column is out of See STEERING COLUMN
Effort alignment article
Improperly installed Adjust or replace
dust shield
Seals or bearings not See STEERING COLUMNS
lubricated article
Mounting bracket screws Replace with new
too long shorter screws
Burrs on shift tube Remove burrs or replace
tube
Lower bowl bearing See STEERING COLUMN
assembled wrong article
Shift tube bent or broken Replace as necessary
Improper adjustment of See STEERING COLUMN
shift levers article
\
\
\
\
\
\
\
Improper Trans. Sheared shift tube joint Replace as necessary
Shifting
Sheared lower shaft lever Replace as necessary
Improper shift lever See STEERING COLUMN
adjustment article
Page 1248 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Improper gate plate See STEERING COLUMN
adjustment article
\
\
\
\](/img/19/57332/w960_57332-1247.png "MITSUBISHI MONTERO 1991 Service Manual Improper gate plate See STEERING COLUMN
adjustment article
\
\
\
\")
Improper gate plate See STEERING COLUMN
adjustment article
\
\
\
\
\
\
\
Excess Play in Instrument panel bracket Tighten bolts and check
Column bolts loose bracket
Broken weld nut on jacket See STEERING COLUMN
article
Instrument bracket capsule See STEERING COLUMN
sheared article
Column bracket/jacket Tighten bolts and check
bolts loose bracket
\
\
\
\
\
\
\
Steering Locks Release lever mechanism See STEERING COLUMN
in Gear article
\
\
\
\
\
\
\
SUSPENSION TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC SUSPENSION TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Front End Noise Loose or worn wheel See Wheel Bearing
Adjustment in
SUSPENSION
Worn shocks or shock Replace struts or strut
mountings mountings
Worn struts or strut Replace struts or strut
mountings mountings
Loose or worn lower control See SUSPENSION
arm
Loose steering gear-to- See STEERING
frame bolts
Worn control arm bushings See SUSPENSION
Ball joints not lubricated Lubricate ball joints &
see Ball Joint Checking
in SUSPENSION
\
\
\
\
\
\
\
Front Wheel Tires or wheels out of Check tire balance
Shake, Shimmy, balance
or Vibration
Incorrect wheel alignment See WHEEL ALIGNMENT
Drive shaft unbalanced Check drive shaft
balance
Page 1249 of 1333
Loose or worn wheel See WHEEL ALIGNMENT
bearings
Loose or worn tie rod ends See SUSPENSION
Worn upper ball joints See Ball Joint Checking
in SUSPENSION
Worn shock absorbers Replace shock absorbers
Worn strut bushings Replace strut bushings
\
\
\
\
\
\
\
Car Pulls to Mismatched or uneven tires Check tire condition
One Side
Broken or sagging springs See SUSPENSION
Loose or worn strut See SUSPENSION
bushings
Improper wheel alignment See WHEEL ALIGNMENT
Improper rear axle Check rear axle
alignment alignment
Power steering gear See STEERING
unbalanced
Front brakes dragging See BRAKES
\
\
\
\
\
\
\
Abnormal Tire Unbalanced tires Check tire balance &
Wear rotation
Sagging or broken springs See SUSPENSION
Incorrect front end See WHEEL ALIGNMENT
alignment
Faulty shock absorbers Replace chock absorbers
\
\
\
\
\
\
\
Scuffed Tires Toe-In incorrect See WHEEL ALIGNMENT
Suspension arm bent or See appropriate
twisted SUSPENSION article
\
\
\
\
\
\
\
Springs Bottom Bent or broken springs See SUSPENSION
or Sag
Leaking or worn shock Replace shock absorbers
absorbers
Frame misalignment Check frame for damage
\
\
\
\
\
\
\
Spring Noises Loose "U" Bolts See SUSPENSION
Loose or worn bushings See SUSPENSION
Worn or missing interliners See SUSPENSION
\
\
\
\
\
\
\
Shock Absorber Loose shock mountings Check & tighten
Noise mountings
Worn bushings Replace bushings
Page 1250 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Air in system Bleed air from system
Undercoating on shocks Remove undercoating
\
\
\](/img/19/57332/w960_57332-1249.png "MITSUBISHI MONTERO 1991 Service Manual Air in system Bleed air from system
Undercoating on shocks Remove undercoating
\
\
\")
Air in system Bleed air from system
Undercoating on shocks Remove undercoating
\
\
\
\
\
\
\
Car Leans or Loose stabilizer bar See SUSPENSION
Sways on Corners
Faulty shocks or mountings Replace shocks or
mountings
Broken or sagging springs See SUSPENSION
\
\
\
\
\
\
\
Shock Absorbers Worn seals or reservoir See SUSPENSION
Leaking tube crimped
\
\
\
\
\
\
\
Broken Springs Loose "U" bolts See SUSPENSION
Inoperative shock absorbers Replace shock absorbers
\
\
\
\
\
\
\
WHEEL ALIGNMENT TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC WHEEL ALIGNMENT TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Premature Tire Improper tire inflation Check tire pressure
Wear
Front alignment out of See ALIGNMENT SPECS in
tolerance WHEEL ALIGNMENT section
Suspension components worn See SUSPENSION section
Steering system components See STEERING section
worn
Improper standing height See WHEEL ALIGNMENT
Uneven or sagging springs See SUSPENSION section
Bent wheel See WHEEL ALIGNMENT
Improper torsion bar See SUSPENSION section
adjustment
Loose or worn wheel See WHEEL BEARING ADJ.
bearings in SUSPENSION section
Worn or defective shock Replace shock absorbers
Tires out of balance Check tire balance
\
\
\
\
\
\
\
Pulls to One Improper tire inflation Check tire pressure
Side
Brake dragging See BRAKE section