wheel MITSUBISHI MONTERO 1991 Service Manual

Fig. 3: Determining Camber Angle
CASTER
1) Caster is tilting of front steering axis either forward or
backward from vertical, as viewed from side of vehicle. See Fig. 4.
2) When axis is tilted backward from vertical, caster is
positive. This creates a trailing action on front wheels. When axis is
tilted forward, caster is negative, causing a leading action on front
wheels.
Fig. 4: Determining Caster Angle
TOE-IN ADJUSTMENT
Toe-in is the width measured at the rear of the tires

subtracted by the width measured at the front of the tires at about
spindle height. A positive figure would indicate toe-in and a negative
figure would indicate toe-out. If the distance between the front and
rear of the tires is the same, toe measurement would be zero. To
adjust:
1) Measure toe-in with front wheels in straight ahead
position and steering wheel centered. To adjust toe-in, loosen clamps
and turn adjusting sleeve or adjustable end on right and left tie
rods. See Figs. 2 and 5.
2) Turn equally and in opposite directions to maintain
steering wheel in centered position. Face of tie rod end must be
parallel with machined surface of steering rod end to prevent binding.
3) When tightening clamps, make certain that clamp bolts are
positioned so there will be no interference with other parts
throughout the entire travel of linkage.
Fig. 5: Wheel Toe-In (Dimension A Less Dimension B)
TOE-OUT ON TURNS
1) Toe-out on turns (turning radius) is a check for bent or
damaged parts, and not a service adjustment. With caster, camber, and
toe-in properly adjusted, check toe-out with weight of vehicle on
wheels.
2) Use a full floating turntable under each wheel, repeating
test with each wheel positioned for right and left turns. Incorrect
toe-out generally indicates a bent steering arm. Replace arm, if
necessary, and recheck wheel alignment.

WIR IN G D IA G RAM S

1991 M it s u bis h i M onte ro
1991 Wiring Diagrams
Mitsubishi
Montero
IDENTIFICATION
COMPONENT LOCATION MENU
COMPONENT LOCATIONS TABLE








\









\









\









\









\









\






Component Figure No. (Location)
A/C RELAYS .......................... 4 (C 12), 4 (A-B 15)
A/C SYSTEM ................................. 4 (A-C 12-15)
ALTERNATOR ................................... 1 (B-C 1-2)
ALTERNATOR RELAY ............................... 1 (C 1-2)
AUTO FREE-WHEELING HUB CONTROL UNIT ............. 3 (D 11)
BACK DOOR LOCK SW ............................... 7 (B 27)
BACK-UP LT SW (M/T) ............................. 7 (A 26)
BATTERY .......................................... 1 (A 1)
BLOWER SWITCH ................................. 4 (A-B 12)
BUZZER .......................................... 5 (E 17)
CARGO LIGHT ..................................... 6 (A 23)
CIG LIGHTER ..................................... 3 (E 11)
CLOCK ........................................... 3 (E 11)
COLUMN SW ..................................... 5 (A-E 19)
CRUISE CONTROL SYSTEM ...................... 4 (D-E 13-15)
DEFOGGER ...................................... 7 (C-D 27)
DIAG CONNECTION .................................. 2 (E 7)
DIMMER CONTROL SWITCH ............................ 3 (E 8)
DIR FLASHER ..................................... 5 (C 16)
DIR SWITCH ...................................... 5 (C 19)
DOME LT ............................... 6 (A 23), 7 (A 24)
DOOR LOCK SYSTEM ........................... 6 (D-E 21-23)
DOOR SWITCHES ......................... 5 (D 17), 6 (C 23)
FRONT WIPER SYSTEM ........................... 5 (A 16-17)
FUEL GAUGE UNIT ................................. 6 (C 22)
FUEL PUMP ........................................ 2 (C 4)
FUSE BLOCK .................................... 3 (C 9-10)
HAZARD FLASHER .................................. 5 (C 16)
HAZARD SW ....................................... 5 (B 16)
HEAD LIGHT WASHER RELAY ....................... 5 (C-D 17)
HEATER RELAY .................................... 4 (A 12)
HORN SWITCH ..................................... 5 (E 19)
IGNITION COIL .................................... 2 (E 4)
IGNITION SW ..................................... 3 (A 11)
ILLUMINATION LIGHTS ............................ 3 (D-E 8)
INHIBITOR SW ..................................... 3 (A 9)
INSTRUMENT CLUSTER ............................ 6 (A-D 20)
KEY REMINDER SW ................................. 5 (E-17)
LIGHT CONTROL RELAY ............................. 5 (E 19)
LIGHT SWITCH .................................... 5 (D 19)
MAIN FUSE LINKS ................................ 1 (A 1-2)
METER UNIT ...................................... 6 (E 20)
MPI CONTROL RELAY ................................ 2 (B 4)
MPI CONTROL UNIT ............................... 2 (A 4-7)
NOISE FILTER ..................................... 2 (E 6)
OVERDRIVE CONTROL RELAY .......................... 3 (A 8)