diagram MITSUBISHI MONTERO 1991 Service Manual

Fig. 10: Vacuum Diagram (Eclipse 2.0L & Galant VIN R/Fed.)
Courtesy of Mitsubishi Motor Sales of America.
Fig. 11: Vacuum Diagram (Eclipse 2.0L VIN U/Calif.)
Courtesy of Mitsubishi Motor Sales of America.

Fig. 12: Vacuum Diagram (Eclipse 2.0L VIN U/Fed.)
Courtesy of Mitsubishi Motor Sales of America.

Fig. 13: Vacuum Diagram (Galant VIN U/Fed.)
Courtesy of Mitsubishi Motor Sales of America.
Fig. 14: Vacuum Diagram (Galant VIN U/Calif.)
Courtesy of Mitsubishi Motor Sales of America.

Fig. 15: Vacuum Diagram (Galant VIN V/Calif.)
Courtesy of Mitsubishi Motor Sales of America.
Fig. 16: Vacuum Diagram (Galant VIN V/Fed.)
Courtesy of Mitsubishi Motor Sales of America.

Fig. 17: Vacuum Diagram (Montero/Calif. & Fed.)
Courtesy of Mitsubishi Motor Sales of America.
Fig. 18: Vacuum Diagram (Pickup 3.0L & Ram-50 3.0L/Fed.)
Courtesy of Mitsubishi Motor Sales of America.

Fig. 19: Vacuum Diagram (Pickup 2.4L & Ram-50 2.4L/Calif. & Fed.)
Courtesy of Mitsubishi Motor Sales of America.
Fig. 20: Vacuum Diagram (Pickup 3.0L & Ram-50 3.0L/Calif.)
Courtesy of Chrysler Motors.

Fig. 21: Vacuum Diagram (Stealth & 3000GT/Fed.)
Courtesy of Chrysler Motors.
Fig. 22: Vacuum Diagram (Stealth & 3000GT/Calif.)
Courtesy of Chrysler Motors.

Fig. 23: Vacuum Diagram (Stealth & 3000GT - Turbo/Calif. & Fed.)
Courtesy of Chrysler Motors.

article in the ACCESSORIES/SAFETY EQUIP Section.
REAR WIPER MOTOR
Removal & Installation
Remove wiper blade and arm assembly. Remove tailgate trim, 2
bolts and wiper motor. To install, reverse removal procedure. Ensure
grommet is in good condition.
REAR WIPER RELAY
Removal & Installation
Rear wiper relay (Except Montero), is located behind right
rear quarter trim. On Montero, relay is located to right of heater
blower housing.
REAR WIPER SWITCH
Removal & Installation
Using flat-bladed tool, pry rear wiper switch from instrument
panel and remove wiring connector. To install, connect wiring
connector, and push switch into instrument panel.
WIRING DIAGRAMS
See appropriate chassis wiring diagram in the WIRING DIAGRAMS
section.

WIR IN G D IA G RAM S YM BO LS
1991 M it s u bis h i M onte ro
WIRING DIAGRAMS
How To Use The Wiring Diagrams
WIRING DIAGRAMS
INTRODUCTION
The wiring diagrams and technical service bulletins,
containing wiring diagram changes, are obtained from the domestic and
import manufacturers. These are checked for accuracy and are all
redrawn into a consistent format for easy use.
All diagrams are arranged with the front of the vehicle at
the left side of the first page and the rear of the vehicle at the
right side of the last page. Accessories are shown near the end of the
diagram.
Components are shown in their approximate location on the
vehicle. Due to the constantly increasing number of components on
vehicles today, it is impossible to show exact locations.
In the past, when cars were simpler, diagrams were simpler.
All components were connected by wires, and diagrams seldom exceeded 4
pages in length. Today some wiring diagrams require more than 16
pages. It would be impractical to expect a service technician to trace
a wire from page 1 across every page to page 16.
Removing some of the wiring maze reduces eyestrain and time
wasted searching across several pages. Today, the majority of diagrams
now follow a much improved format, which permits space for internal
switch details and connector shapes.
Any wires that don't connect directly to their components are
identified on the diagram to indicate where they go. There is a legend
on the first page of each diagram, detailing component location. It
refers you to sub-systems, using grid NUMBERS at the top and bottom of
the page and grid LETTERS on each side. This grid system works in a
manner similar to that of a road map.
HOW TO USE THE WIRING DIAGRAMS
1) On the first page of the diagram, you will find a listing
of major electrical components or systems. Locate the specific
component or system you wish to trace. A grid number and letter will
follow the component's name.
2) Use the grid NUMBERS (arranged horizontally across the top\
and bottom of each page) to find the page of the wiring diagram that
contains the component you're seeking. When you reach this page, use
the grid LETTERS on the side of the page to determine the component's
vertical location.
3) Locate the circuit you need to service. The internals are
shown for switches and relays to assist you in understanding how the
circuit operates.
NOTE: In some of the newer wiring diagram articles in this
product, there is a Legend for the wiring diagrams that has
been created to make locating components easier. For these
articles, there will be a COMPONENT LOCATION MENU title in
the article main menu. These articles will also have the
original legend available on the first graphic.