boot MITSUBISHI MONTERO 1991 Owner's Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 712 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual concern.
\
\
\
\
\
\](/img/19/57332/w960_57332-711.png "MITSUBISHI MONTERO 1991 Owners Manual concern.
\
\
\
\
\
\")
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-94 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
60,000 MILE (96,000 KM) SERVICE
60,000 MILE (96,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Valve Clearance (Jet Valve Only)
\b\
\
\
\
\
\
\
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (2.6L Engine)
\b\
\
\
\
\
\
\
Crankcase Emission Control System (PCV Valve)
\b\
\
\
\
\
\
\
Evaporative Emission Control System
\b\
\
\
\
\
\
\
Distributor Cap, Rotor & Spark Advanced System
\b\
\
\
\
\
\
\
Intake Temperature Control System
\b\
\
\
\
\
\
\
Secondary Air System
\b\
\
\
\
\
\
\
Front Disc Pads
\b\
\
\
\
\
\
\
Rear Drum Brake Linings & Wheel & Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joints
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\b\
\
\
\
\
\
\
Vacuum, Water, Crankcase Ventilation & Secondary Air Hoses
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter
Page 715 of 1333
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-95 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
75,000 MILE (120,000 KM) SERVICE
75,000 MILE (120,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
Page 717 of 1333
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-95 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
90,000 MILE (144,000 KM) SERVICE
90,000 MILE (144,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Valve Clearance (Jet Valve Only)
\b\
\
\
\
\
\
\
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (If Equipped)
\b\
\
\
\
\
\
\
Disc Brake Pads
\b\
\
\
\
\
\
\
Drum Brake Linings & Rear Wheel Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Fuel & Vapor Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joint
\b\
\
\
\
\
\
\
Power Steering Fluid (If Equipped)
\b\
\
\
\
\
\
\
Power Steering Hoses (If Equipped)
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Lubricate Upper Control Arm Bushings
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\
\
\
\
\
\
\
Page 720 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual Fluid Capacities
\
\
\
\
\
\](/img/19/57332/w960_57332-719.png "MITSUBISHI MONTERO 1991 Owners Manual Fluid Capacities
\
\
\
\
\
\")
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-95 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
105,000 MILE (168,000 KM) SERVICE
105,000 MILE (168,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
Page 723 of 1333
![MITSUBISHI MONTERO 1991 Owners Manual Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\](/img/19/57332/w960_57332-722.png "MITSUBISHI MONTERO 1991 Owners Manual Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\")
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (2.6L Engine)
\b\
\
\
\
\
\
\
Crankcase Emission Control System (PCV Valve)
\b\
\
\
\
\
\
\
Evaporative Emission Control System
\b\
\
\
\
\
\
\
Distributor Cap, Rotor & Spark Advanced System
\b\
\
\
\
\
\
\
Intake Temperature Control System
\b\
\
\
\
\
\
\
Secondary Air System
\b\
\
\
\
\
\
\
Front Disc Pads
\b\
\
\
\
\
\
\
Rear Drum Brake Linings & Wheel & Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joints
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\b\
\
\
\
\
\
\
Vacuum, Water, Crankcase Ventilation & Secondary Air Hoses
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter
\b\
\
\
\
\
\
\
Fuel Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Ignition Cables
\b\
\
\
\
\
\
\
Camshaft Timing Belt
\b\
\
\
\
\
\
\
Engine Coolant
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Vacuum Control System Solenoid Valve Air Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Page 784 of 1333
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Dust boot missing ....... 2 ........ (1) Suggest replacement.
Dust boot split ......... 2 ........ ( 1) Suggest replacement.
Dust boot torn .......... 2 ........ ( 1) Suggest replacement.
Housing cracked ......... A ............ Require replacement.
Lead routing incorrect .. B .. Require rerouting according to
vehicle manufacturer's
specifications.
Loose ................... B ... Require adjustment to vehicle
manufacturer's specifications.
Missing ................. C ............ Require replacement.
Output signal incorrect . A .. Require repair or replacement.
Wire lead damaged ....... A .. Require repair or replacement.
( 1) - This condition can lead to damage of the sliding magnet,
which, in turn, causes premature sensor failure.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - MODULES
AIR RIDE SUSPENSION - MODULE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Housing cracked ......... 2 .. Suggest repair or replacement.
Inoperative ............. A ............ Require replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - RELAYS (COMPRESSOR)
AIR RIDE SUSPENSION - RELAY (COMPRESSOR) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Housing cracked ......... 2 ........ ( 1) Suggest replacement.
Intermittent ............ A ............ Require replacement.
Missing ................. C ............ Require replacement.
Output signal incorrect . A ............ Require replacement.
( 1) - If moisture enters the relay, it can reduce life
expectancy or impair function.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - SWITCHES (ON/OFF)
Page 787 of 1333
previously diagnosed by the "perceptible movement"
standard. Before requiring or suggesting any parts be
replaced based on "perceptible movement," consult your
repair manual to determine if OEM specifications exist.
You are not required to replace ball joints in axle sets.
However, when replacing a ball joint due to wear exceeding
manufacturer's specification, you may suggest replacement of the other
ball joint if its measurement shows it is close to the end of its
useful life, for preventive maintenance.
BALL JOINT INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware bent . B ... Require repair or replacement
of bent part if available;
otherwise, replace ball joint.
Attaching hardware
broken ................. A ... Require replacement of broken
part if available; otherwise,
replace ball joint.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
part if available; otherwise,
replace ball joint.
Attaching hardware
incorrect ............... A .......... Require replacement of
incorrect part if available;
otherwise, replace ball joint.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part if available;
otherwise, replace ball joint.
Attaching hardware
missing ................ C .. Require replacement of missing
part if available; otherwise,
replace ball joint.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads if
available; otherwise, replace
ball joint.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads if
available; otherwise, replace
ball joint.
Binding ................. A .......... (1) Further inspection
required.
Grease boot cracked ..... 2 ........ ( 2) Suggest replacement.
Grease boot missing ..... 2 ........ ( 3) Suggest replacement.
Grease boot torn ........ 2 ........ ( 4) Suggest replacement.
Grease fitting broken ... A ... Require replacement of grease
fitting.
Grease fitting missing .. C ... Require replacement of grease
fitting.
Grease fitting
won't seal ............. A ... Require replacement of grease
fitting.
Greaseable ball joint will
Page 788 of 1333
not take grease ........ 2 ...... (5) Suggest replacement of
grease fitting.
Nut on ball joint loose . A ........... ( 6) Require repair or
replacement.
Pre-load adjustment
incorrect .............. B .. Require repair or replacement.
Seized .................. A ............ Require replacement.
Stud bent ............... B ........ ( 7) Require replacement.
Stud broken ............. A ........ ( 7) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications ......... B ............ Require replacement.
( 1) - If greaseable, grease ball joint. If problem persists
or joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the ball joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the ball joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
ball joint and will accelerate wear.
( 5) - If the greaseable ball joint still will not take grease
after replacing the grease fitting, suggest replacement
of ball joint.
( 6) - Check for bent stud or damaged taper hole.
( 7) - Check for damaged taper hole.
\
\
\
\
\
\
\
BUSHINGS
BUSHING INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware bent . B ... Require repair or replacement
of bent part if available;
otherwise, replace bushing.
Attaching hardware
broken ................. A ... Require replacement of broken
part if available; otherwise,
replace bushing.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
part if available; otherwise,
replace bushing.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part if available;
otherwise, replace bushing.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part if available;
otherwise, replace bushing.
Attaching hardware
missing ................ C .. Require replacement of missing
part if available; otherwise,
replace bushing.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
Page 790 of 1333
available; otherwise, replace
center link.
Bent .................... B ............ Require replacement.
Binding ................. A ........... (1) Further inspection
required.
Grease boot cracked ..... 2 ........ ( 2) Suggest replacement.
Grease boot missing ..... 2 ........ ( 3) Suggest replacement.
Grease boot torn ........ 2 ........ ( 4) Suggest replacement.
Grease fitting broken ... A ... Require replacement of grease
fitting.
Grease fitting missing .. C ... Require replacement of grease
fitting.
Grease fitting
won't seal ............. A ... Require replacement of grease
fitting.
Grease seal missing ..... 2 ........ ( 3) Suggest replacement.
Grease seal torn ........ 2 ........ ( 4) Suggest replacement.
Looseness (perceptible
horizontal movement) ... 1 ........ ( 5) Suggest replacement.
Looseness that is
excessive .............. B ..... ( 5)( 6) Require replacement.
Seized .................. A ............ Require replacement.
Stud bent ............... B ........ ( 7) Require replacement.
Stud broken ............. A ........ ( 7) Require replacement.
Stud loose in
taper hole ............. A ........... ( 7) Require repair or
replacement.
Taper hole elongated .... A ........ ( 8) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications ......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and socket
movement. Use only moderate hand pressure.
( 6) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 7) - Check for damaged taper hole.
( 8) - Check for damaged stud.
\
\
\
\
\
\
\
CONTROL ARM SHAFTS
CONTROL ARM SHAFT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require replacement of broken
Page 792 of 1333
if available; otherwise,
replace control arm.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
control arm.
Bent .................... B ............ Require replacement.
Bushing hole oversized .. B ............ Require replacement.
Ball joint hole oversized
(loose interference or
press fit) ............. B .......... (1) Further inspection
required.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Holes distorted ......... A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - If oversized ball joint is available, require
replacement of ball joint. If oversized ball joint
is not available, require replacement of control arm.
\
\
\
\
\
\
\
DRAG LINKS
DRAG LINK INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace drag link.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace drag link.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace drag link.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace drag link.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
drag link.
Bent .................... B ............ Require replacement.
Binding ................. A .......... ( 1) Further inspection
required.
Grease boot cracked ..... 2 ........ ( 2) Suggest replacement.
Grease boot missing ..... 2 ........ ( 3) Suggest replacement.
Grease boot torn ........ 2 ........ ( 4) Suggest replacement.
Grease fitting broken ... A ... Require replacement of grease
fitting.