key MITSUBISHI MONTERO 1991 Owner's Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1991, Model line: MONTERO, Model: MITSUBISHI MONTERO 1991Pages: 1333, PDF Size: 24.61 MB
Page 621 of 1333
Starters
Generator .................................. Generators & Regulators
Engine Performance
Power Distribution
Generic Electronic Module (GEM) ............... Body Control Modules\
Electronic Suspension
Glow Plug Relay ................................. Engine Performance
Glow Plugs ...................................... Engine Performance
Grounds ........................................ Ground Distribution
Headlight Door Module .............................. Headlight Doors
Headlight Relay .................................. Headlight Systems
Daytime Running Lights
Headlights ....................................... Headlight Systems
Daytime Running Lights
Heated Oxygen Sensor(s) (HO2S) .................. Engine Performan\
ce
Heated Windshield Control Module ................ Heated Windshields
Height Sensor ................................ Electronic Suspension
Horns ..................................... Steering Column Switches
Horn Relay ................................ Steering Column Switches
Idle Air Control (IAC) Motor/Valve .............. Engine Performance\
Ignition Coil(s) ................................ Engine Performance\
Ignition Key Lock Cylinder ....................... Anti-Theft System
Ignition Module ................................. Engine Performance
Ignition Switch ................................. Power Distribution
Engine Performance
Generators & Regulators
Starters
Illuminated Entry Module .............. Illumination/Interior Lights
Illumination Lights ................... Illumination/Interior Lights
Impact Sensor ............................. Air Bag Restraint System
Inertia Fuel Shutoff Switch ..................... Engine Performance
Inhibit Relay ............................................. Starters
Instrument Cluster ........................ Analog Instrument Panels
Intake Air Temperature (IAT) Sensor ............. Engine Performance\
Interior Lights ....................... Illumination/Interior Lights
Interlock Switch .......................................... Starters
Junction Block .................................. Power Distribution
Keyless Entry Receiver ........................ Remote Keyless Entry
Key Reminder Switch ....................................... Starters
Knock Sensor .................................... Engine Performance
Lamp Control Module ................................ Exterior Lights
License Plate Lamp ................................. Exterior Lights
Lighting Control Module ................... Lighting Control Modules
Anti-Theft System
Daytime Running Lights
Headlight Systems
Lower Relay .................................. Power Convertible Top
Malfunction Indicator Light (MIL) ............... Engine Performance\
Instrument Panels
Manifold Absolute Pressure (MAP) Sensor ......... Engine Performance\
Mass Airflow (MAF) Sensor ....................... Engine Performance\
Mega Fuse .................................. Generators & Regulators
Memory Seat/Mirror Module ........................... Memory Systems
Mirror Defogger ............................... Rear Window Defogger
Moon Roof Motor .................................... Power Moon Roof
Moon Roof Relay .................................... Power Moon Roof
Multi-Function Control Module ...................... Warning Systems
Neutral Safety Switch ..................................... Starters
Oil Level Switch ................................ Engine Performance
Oil Pressure Switch/Sending Unit .......... Analog Instrument Panels
Engine Performance
Overhead Console .................................. Overhead Console
Oxygen Sensor(s) (O2S) .......................... Engine Performan\
ce
Page 656 of 1333
LO CKIN G H UBS
1991 M it s u bis h i M onte ro
1991 DRIVE AXLES
Locking Hubs
Mitsubishi: Montero, Pickup
DESCRIPTION
Automatic hubs are engaged by rotational force of axle shaft
when 4WD is selected at transfer case. Automatic hubs disengage when
2WD is selected or vehicle is driven in Reverse. Cams, brakes and
springs are used to lock or unlock automatic hubs.
Engagement is accomplished through gears and spring actions
within hub. When hub is locked, hub brake engages inner hub, which is
connected to axle shaft by inner splines of hub. Hub brake is
connected to hub body by outer splines.
REMOVAL
1) Hub must be unlocked. To unlock hub, place transfer case
lever in 2H position and move vehicle in Reverse approximately 4-6
feet.
2) Remove cover from locking hub. If hub cover cannot be
loosened by hand, wrap shop towel around cover and use an oil filter
wrench to loosen cover.
3) Raise and support vehicle. Remove wheel assembly. Using
snap ring pliers, remove snap ring and shim from end of axle. Remove
locking hub retaining bolts. Remove locking hub.
INSTALLATION
1) To install, reverse removal procedure. Apply sealant to
contact areas between locking hub assembly and hub/rotor assembly.
Ensure sealant is NOT applied on outer areas of hub/rotor assembly
toward brake contact areas.
2) Align locking hub assembly key area with steering knuckle
key way area. Loosely install locking hub assembly on hub/rotor
assembly. Ensure locking hub assembly fully contacts hub/rotor
assembly.
3) Install locking hub retaining bolts. Tighten bolts to 36-
43 ft. lbs. (49-58 N.m). Using spring scale attached to wheel stud,
measure turning resistance required to rotate hub/rotor assembly.
4) Turning resistance should NOT exceed 3.1 lbs. (1.4 kg). I\
f
turning resistance exceeds specification, check for incorrect
installation of locking hub assembly or components.
5) Install shim and snap ring on drive axle. Rotate drive
axle until maximum end play is obtained. Using a dial indicator, check
drive axle end play.
6) Drive axle end play should be .008-.020" (.20-.51 mm). If\
axle end play is NOT within specification, adjust end play by changing
axle shaft shim. Install hub cover. Tighten hub cover 13-25 ft. lbs.
(18-34 N.m).
OVERHAUL
DISASSEMBLY
Page 670 of 1333
2.6L Engine ........................................... 45
2.6L Optional ......................................... 45
3.0L V6 ........................................... (1) 24
3.5L V6 ........................................... ( 1) 24
( 1) - Check hood clearance on 1986 and newer models.
\
\
\
\
\
\
CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG SYSTEM
NOTE: See the AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
The SRS has no user-servicable parts. Always have servicing
done by an authorized dealer.
When performing maintenance on air bag equipped vehicles
always observe proper safety precautions.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
ANTI-LOCK BRAKE SYSTEM (ABS)
CAUTION: Never mix different diameter tires. On loose or uneven
surfaces, the ABS system may require longer stopping
distances than conventional brake systems. Exercise caution
when removing mud or snow from the wheels so as not to
damage the ABS wiring or speed sensors.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
appropriate COMPUTER RELEARN PROCEDURES article in the
GENERAL INFORMATION section below.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BRAKE PAD WEAR INDICATOR
Indicator will cause a squealing or scraping noise, warning
that brake pads need replacement.
Page 671 of 1333
CATALYTIC CONVERTER
Continued operation of vehicle with a severe malfunction
could cause converter to overheat, resulting in possible damage to
converter and vehicle.
COOLANT (PROPYLENE-GLYCOL FORMULATIONS)
CAUTION: To avoid possible damage to vehicle use only ethylene-glycol
based coolants with a mixture ratio from 44-68% anti-freeze.
DO NOT use 100% anti-freeze as it will cause the formation
of cooling system deposits. This results in coolant
temperatures of over 300
\b F (149\bC) which can melt plastics.
100% anti-freeze has a freeze point of only -8\b F (-22\bC).
CAUTION: Propylene-Glycol Mixtures has a smaller temperature range
than Ethylene-Glycol. The temperature range (freeze-boil)
of a 50/50 Anti-Freeze/Water Mix is as follows:
Propylene-Glycol -26
\b F (-32\bC) - 257\b F (125\bC)
Ethylene-Glycol -35\b F (-37\bC) - 263\b F (128\bC)
CAUTION: Propylene-Glycol/Ethylene-Glycol Mixtures can cause the
destabilization of various corrosion inhibitors. Also
Propylene-Glycol/Ethylene-Glycol has a different specific
gravity than Ethylene-Glycol coolant, which will result in
inaccurate freeze point calculations.
ELECTROSTATIC DISCHARGE SENSITIVE (ESD) PARTS
WARNING: Many solid state electrical components can be damaged by
static electricity (ESD). Some will display a warning label,
but many will not. Discharge personal static electricity by
touching a metal ground point on the vehicle prior to
servicing any ESD sensitive component.
ENGINE OIL
CAUTION: Never use non-detergent or straight mineral oil.
FUEL SYSTEM SERVICE
WARNING: Relieve fuel system pressure prior to servicing any fuel
system component (fuel injection models).
HALOGEN BULBS
WARNING: Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare
hands. Eye protection should be worn when handling or working
around halogen bulbs.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.
RADIATOR FAN
Page 675 of 1333
1 - 20 Amp
Not Used
2 - Not Used
10 Amp (1994-96)
ELC-4 A/T Control Module, Cruise Control Unit
3 - 10 Amp
Blower Motor Relay, Headlight Washer Relay, Defogger Relay,
Car Telephone (1992-93)
4 - 10 Amp
Radio Clock, Accessory Socket Relay,
Cruise Control Unit (1994-96), Data Link Connector (1994-96)\
5 - 15 Amp
Remote Controlled Mirror, Cigarette Lighter
Accessory Socket Relay (1992-93)
6 - 15 Amp
Door Lock Relay, Door Lock Control Unit (1994-96)
7 - 10 Amp
Overdrive Relay, Variable Shock Absorber Control Unit,
4WD Indicator Control Unit, ABS Power Relay (1992-93),
ABS Control Unit (1994-96), Combination Meter (1994-96)
8 - 10 Amp
Power Window Relay
9 - 15 Amp
Wiper, Washer, Sunroof
10 - 10 Amp
Horn, Cruise Control Unit (1992-93)
11 - 10 Amp
Combination Meter, Multi-meter, Motor Antenna Control Unit,
Buzzer Assembly
12 - 15 Amp
Turn Signal Light, Hazard Light, SRS Diagnosis Unit
13 - 10 Amp
Not Used
14 - 15 Amp
Accessory Socket
15 - Not Used
16 - 25 Amp
Blower Motor
17 - 15 Amp
Stoplight
18 - 10 Amp
Back-up Light, Rear Differential Lock Control Unit
19 - 10 Amp
Engine Control Module, Dome Light, Reading Light,
Cargo Light, Combination Meter, Clock, Door Lock Relay,
Cruise Control Unit, Car Telephone (1992-93)
ELC-4 A/T Control Module (1994-96), Ignition Key Illumination\
Light Timer (1994-96)
Page 696 of 1333
SC HED ULE D S ER VIC ES
1991 Mitsubishi Montero
1987-95 MAINTENANCE
Mitsubishi Maintenance & Service Intervals
Montero
* PLEASE READ THIS FIRST *
NOTE: All SERVICE SCHEDULES are listed for normal service
vehicles. If vehicle is operated under severe service
conditions, see
SEVERE SERVICE REQUIREMENTS (PERFORM W/SERVICE SCHEDULES)
for items requiring additional maintenance.
NOTE: This article contains scheduled maintenance service
information. Fluid types and capacities listed with each
service in this article are only those necessary to perform
that scheduled service. For specifications pertaining to
fluid capacities for the entire vehicle, fuse and circuit
breaker identification, wheel and tire size, battery type,
warranty information, or model identification refer to the
MAINTENANCE INFORMATION article in this section.
CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (AIR BAG)
NOTE: See the AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
Modifications or improper maintenance, including incorrect
removal and installation of the Supplemental Restraint System (SRS),
can adversely affect system performance. DO NOT cover, obstruct or
change the steering wheel horn pad in any way, as such action could
cause improper function of the system. Use only plain water when
cleaning the horn pad. Solvents or cleaners could adversely affect the
air bag cover and cause improper deployment of the system.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
AIR CONDITIONING SERVICING
WARNING: R-134a service equipment or vehicle A/C systems SHOULD NOT
be pressure tested or leak tested with compressed air. Some
mixtures of air/R134a have shown to be combustible at
elevated pressures. These mixtures are dangerous and may
cause fire and/or explosions. See the appropriate
A/C SYSTEM GENERAL SERVICING article in the AIR CONDITIONING
& HEAT section.
Page 697 of 1333
WARNING: Avoid breathing R-134a refrigerant and PAG lubricant vapors,
exposure may irritate eyes, nose and throat. To remove
R-134a from system use R-134a recycling equipment that meets
SAE J2210 specifications. If accidental system discharge
occurs, ventilate work area before resuming service.
ANTI-LOCK BRAKE SYSTEM
The anti-lock brake system contains electronic equipment that
can be susceptible to interference caused by improperly installed or
high output radio transmitting equipment. Since this interference
could cause the possible loss of the anti-lock braking capability,
such equipment should be installed by qualified professionals.
On models equipped with anti-lock brake systems, ALWAYS
observe the following cautions:
* DO NOT attempt to bleed hydraulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES Section.
* DO NOT mix tire sizes. As long as tires remain close to the
original diameter, increasing the width is acceptable.
Rolling diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* Use ONLY recommended brake fluids. DO NOT use silicone brake
fluids in an ABS-equipped vehicle.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
appropriate COMPUTER RELEARN PROCEDURES article in the
GENERAL INFORMATION section below.
BRAKE FLUID
For vehicles equipped with a traction control system, idle
engine while pouring brake fluid into reservoir.
CATALYTIC CONVERTER
Continued operation of vehicle with a severe malfunction
could cause converter to overheat, resulting in possible damage to
converter and vehicle.
ELECTROSTATIC DISCHARGE SENSITIVE (ESD) PARTS
WARNING: Many solid state electrical components can be damaged by
static electricity (ESD). Some will display a warning label,
but many will not. Discharge personal static electricity by
Page 698 of 1333
touching a metal ground point on the vehicle prior to
servicing any ESD sensitive component.
ENGINE OIL
CAUTION: Never use non-detergent or straight mineral oil.
FUEL SYSTEM SERVICE
WARNING: Relieve fuel system pressure prior to servicing any fuel
system component (fuel injection models).
HALOGEN BULBS
Halogen bulbs contain pressurized gas which may explode if
overheated. DO NOT touch glass portion of bulb with bare hands. Eye
protection should be worn when handling or working around halogen
bulbs.
POWER STEERING FLUID
When adding power steering fluid, avoid spilling. Damage to
alternator, located beneath power steering reservoir, could result.
RADIATOR CAP
CAUTION: Always disconnect the fan motor when working near the
radiator fan. The fan is temperature controlled and could
start at any time even when the ignition key is in the OFF
position. DO NOT loosen or remove radiator cap when cooling
system is hot.
RADIATOR FAN
WARNING: Keep hands away from radiator fan. Fan is controlled by a
thermostatic switch which may come on or run for up to 15
minutes even after engine is turned off.
SERVICE POINT LOCATIONS
Fig. 1: Service Point Locations (1987-91 2.6L 4-Cylinder Engine)
Courtesy of Mitsubishi Motor Sales of America.
Page 756 of 1333
STE ER IN G C O LU M N S W IT C HES
1991 M it s u bis h i M onte ro
1991 ACCESSORIES & SAFETY EQUIPMENT
Chrysler Motors/Eagle/Mitsubishi Steering Column Switches
Dodge; Colt, Colt Vista, Colt 200, Ram-50, Stealth
Eagle; Summit
Mitsubishi: Eclipse, Galant, Mirage, Montero, Pickup, 3000Gt
Plymouth; Colt, Colt Vista, Colt 200
TESTING
For steering column switch testing, see STEERING COLUMN
SWITCH TESTING/REMOVAL & INSTALLATION table for figure reference.
STEERING COLUMN SWITCH TESTING/REMOVAL & INSTALLATION TABLE
\
\
\
\
\
\
Model Figure Number
Colt, Colt 200, Mirage & Summit ............... See Fig. 1
Colt Vista .................................... See Fig. 2
Eclipse ....................................... See Fig. 3
Galant ........................................ See Fig. 4
Montero ....................................... See Fig. 5
Pickup & Ram-50 ............................... See Fig. 6
Stealth & 3000GT .............................. See Fig. 7
\
\
\
\
\
\
REMOVAL & INSTALLATION
IGNITION SWITCH
Removal (Colt, Colt 200, Eclipse, Mirage & Summit)
1) Remove steering column switch. See STEERING COLUMN SWITCH
under REMOVAL & INSTALLATION. On automatic transaxle vehicles,
disconnect key interlock cable, and remove spring and slide lever.
2) On all vehicles, insert key and turn ignition switch to
ACC position. Push steering lock cylinder lock pin inward and pull
steering lock cylinder away from dash. Remove ignition switch and key
reminder switch.
Installation
1) Place ignition switch in LOCK position. Install slide
lever to steering lock cylinder. Install spring to inner cable of key
interlock cable (if used).
2) Connect key interlock cable to slide lever and steering
lock cylinder. Lightly grease around slide lever. To complete
installation, reverse removal procedure. Ensure key interlock system
functions properly.
Removal & Installation (Colt Vista, Galant, Montero, Pickup,
Ram-50, Stealth & 3000GT)
Remove knee protector (if necessary). Remove upper and lower
column covers. Remove air ducts and cable bands as necessary. Remove
ignition switch and key reminder switch. To install, reverse removal
procedure.
STEERING COLUMN SWITCH
Removal & Installation (Except Stealth & 3000GT)
Page 768 of 1333
1) Using Socket (MB990954) and torque wrench, rotate front
hub and tighten lock nut to 95-145 ft. lbs. (129-197 N.m) to seat
bearings. Loosen nut. Retighten nut to 18 ft. lbs. (24 N.m) and loosen\
30-40 degrees.
2) Using spring scale attached to wheel stud, measure and
record turning resistance required to rotate hub/rotor assembly before
installing locking hub.
3) Apply semi-drying sealant on locking hub assembly-to-
hub/rotor contact areas. DO NOT apply sealant on outer areas of
hub/rotor assembly, toward brake contact areas.
4) Align locking hub assembly key area with steering knuckle
keyway area. Loosely install locking hub assembly on hub/rotor
assembly. Ensure locking hub assembly fully contacts hub/rotor
assembly.
5) Install locking hub retaining bolts. Tighten to
specification. See TORQUE SPECIFICATIONS table at end of article.
Using spring scale attached to wheel stud, measure turning resistance
required to rotate hub/rotor assembly.
6) Subtract turning resistance measured in step 2) (before
installing locking hub) from turning resistance measured in step 5)
(after installing locking hub). If difference exceeds 3.1 lbs. (14 N)\
,
check for incorrect installation of locking hub assembly or
components.
7) Install shim and snap ring on drive axle. Rotate drive
axle until maximum end play is obtained. Using dial indicator, check
drive axle end play.
8) Drive axle end play should be .008-.020" (.20-.51 mm). If\
end play is not within specification, adjust drive axle end play by
changing axle shaft shim. Install new "O" ring and cover. Tighten
cover to specification. See TORQUE SPECIFICATIONS table at end of
article.
LOWER CONTROL ARM R & I
REMOVAL
1) Raise and support vehicle. Remove wheel assembly. Remove
front skid plate and undercover (if equipped). Remove torsion bar. See\
TORSION BAR under REMOVAL & INSTALLATION. Remove stabilizer bar bolt
from control arm.
2) Remove shock absorber-to-control arm bolts. Loosen but DO
NOT remove lower ball joint-to-steering knuckle nut. Using ball joint
fork, separate lower ball joint from steering knuckle.
3) Remove ball joint stud nut from steering knuckle. Remove
control arm shaft. See Fig. 1. Remove torque arm. Remove lower control
arm pivot bolt. Remove lower control arm.
INSPECTION
1) Inspect control arm for cracks or deformation. Check ball
joints. See BALL JOINT CHECKING under ADJUSTMENTS & INSPECTION.
2) Inspect ball joint dust covers for damage. Replace dust
covers if damaged. Inspect control arm bushing and frame bracket
bushing for damage. Replace if necessary.
3) If frame bracket bushing needs replacing, install Bushing
Remover/Installer (MB990958-01) in bushing. See Fig. 3. Tighten
bushing remover/installer bolt until bushing is removed. Reverse
bushing remover/installer to install bushing.
NOTE: Differential carrier may require relocation to replace left
bracket bushing.