fuel MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 1390 of 1501
![MITSUBISHI MONTERO 1998 Service Manual Incorrect injector pump Check pressure, see
housing pressure FUEL SYSTEMS
\
\
\](/img/19/57333/w960_57333-1389.png "MITSUBISHI MONTERO 1998 Service Manual Incorrect injector pump Check pressure, see
housing pressure FUEL SYSTEMS
\
\
\")
Incorrect injector pump Check pressure, see
housing pressure FUEL SYSTEMS
\
\
\
\
\
\
\
Engine Cooling system leaks Check cooling system
Overheating and repair leaks
Belt slipping or damaged Check tension and/or
replace belt
Thermostat stuck closed Remove and replace
thermostat, see
ENGINE COOLING
Head gasket leaking Replace head gasket
\
\
\
\
\
\
\
Oil Light on at Low oil pump pressure Check oil pump
Idle operation, see ENGINES
Oil cooler or line Remove restriction
restricted and/or replace cooler
\
\
\
\
\
\
\
Engine Won't Injector pump fuel solenoid Remove and check
Shut Off does not return fuel valve solenoid and replace
to OFF position if needed
\
\
\
\
\
\
\
VACUUM PUMP DIAGNOSIS
Excessive Noise Loose pump-to-drive Tighten screws
assembly screws
Loose tube on pump assembly Tighten tube
Valves not functioning Replace valves
properly
Oil Leakage Loose end plug Tighten end plug
Bad seal crimp Remove and re-crimp
seal
\
\
\
\
\
\
\
FUEL INJECTION TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC FUEL INJECTION TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Engine Won't Cold start valve inoperative Test valve and
Start (Cranks circuit
Normally)
Poor connection;vacuum or Check vacuum and
wiring electrical
connections
Contaminated fuel Test fuel for water
or alcohol
Defective fuel pump relay Test relay and
or circuit wiring
Battery too low Charge and test
battery
Page 1391 of 1501
Low fuel pressure Test pressure regul-
ator and fuel pump,
check for restricted
lines and filters
No distributor reference Repair ignition
pulses system as necessary
Open coolant temperature Test sensor and
sensor circuit wiring
Shorted W.O.T. switch in Disconnect W.O.T.
T.P.S. switch, engine
should start
Defective ECM Replace ECM
Fuel tank residual pressure Test for fuel
valve leaks pressure drop after
shut down
\
\
\
\
\
\
\
Hard Starting Disconnected hot air tube Reconnect tube and
to air cleaner test control valve
Defective Idle Air Control Test valve operation
(IAC) valve and circuit
Shorted, open or misadjusted Test and adjust or
T.P.S. replace T.P.S.
EGR valve open Test EGR valve and
control circuit
Poor Oxygen sensor signal Test for shorted or
circuit
Incorrect mixture from PCV Test PCV for flow,
system check sealing of oil
filter cap
\
\
\
\
\
\
\
Poor High Speed Low fuel pump volume Faulty pump or
Operation restricted fuel
lines or filters
Poor MAP sensor signal Test MAP sensor,
vacuum hose and
wiring
Poor Oxygen sensor signal Test for shorted or
open sensor or
circuit
Open coolant temperature Test sensor and
sensor circuit wiring
Faulty ignition operation Check wires for
cracks or poor con-
nections, test
secondary voltage
with oscilloscope
Contaminated fuel Test fuel for water
Page 1392 of 1501
or alcohol
Intermittent ECM ground Test ECM ground
connection for
resistance
Restricted air cleaner Replace air cleaner
Restricted exhaust system Test for exhaust
manifold back
pressure
Poor MAF sensor signal Check leakage
between sensor and
manifold
Poor VSS signal If tester for ALCL
hook-up is available
check that VSS
reading matches
speedometer
\
\
\
\
\
\
\
Ping or Knock on Poor Knock sensor signal Test for shorted or
Acceleration open sensor or
circuit
Poor Baro sensor signal Test for shorted or
open sensor or
circuit
Improper ignition timing See VEHICLE EMISSION
CONTROL LABEL (where
applicable)
Check for engine Low coolant, loose
overheating problems belts or electric
cooling fan
inoperative
\
\
\
\
\
\
\
NOTE: For additional electronic fuel injection trouble shooting
information, see the appropriate article in the ENGINE
PERFORMANCE section (not all vehicles have Computer Engine
Control articles). Information is provided there for
diagnosing fuel system problems on vehicles with electronic
fuel injection.
IGNITION SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
Ignition Secondary Trouble Shooting Chart
\
\
\
\
\
\
START: Visually inspect Spark Plug Wires, Coil Wires,
Plug Wire Boots, Rotor, and Distributor Cap for
signs of damage.
Page 1398 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
High Pitched Whine Distance too great](/img/19/57333/w960_57333-1397.png "MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
High Pitched Whine Distance too great")
\
\
\
\
\
\
\
High Pitched Whine Distance too great Align starter or check
During Cranking between starter that correct starter
Before Engine pinion and flywheel and flywheel are being
Fires but Engine used
Fires and Cranks
Normally
\
\
\
\
\
\
\
High Pitched Distance too small between
Whine After Engine starter pinion and flywheel
Fires With Key Flywheel runout contributes
released. Engine to the intermittent nature
Fires and Cranks
Normally
\
\
\
\
\
\
\
TUNE-UP TROUBLE SHOOTING - GAS ENGINE VEHICLES
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC SPARK PLUG TROUBLE SHOOTING CHARTS
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Normal Spark Light Tan or Gray deposits No Action
Plug Condition
Electrode not burned or No Action
fouled
Gap tolerance not changed No Action
\
\
\
\
\
\
\
Cold Fouling or Overrich air/fuel mixture Adjust air/fuel
Carbon Deposits mixture, see ENGINE
PERFORMANCE section
Faulty choke Replace choke
assembly, see ENGINE
PERFORMANCE section
Clogged air filter Clean and/or replace
air filter
Incorrect idle speed or Reset idle speed and/
dirty carburetor or clean carburetor
Faulty ignition wires Replace ignition
wiring
Prolonged operation Shut engine off
at idle during long idle
Sticking valves or worn Check valve train
valve guide seals
\
\
\
\
\
\
\
Wet Fouling Worn rings and pistons Install new rings and
or Oil Deposits pistons
Page 1399 of 1501
Excessive cylinder wear Rebore or replace
block
Excessive valve guide Worn or loose bearing
clearance
\
\
\
\
\
\
\
Gap Bridged Deposits in combustion Clean combustion
chamber becoming fused chamber of deposits
to electrode
\
\
\
\
\
\
\
Blistered Engine overheating Check cooling system
Electrode
Wrong type of fuel Replace with correct
fuel
Loose spark plugs Retighten spark plugs
Over-advanced ignition Reset ignition timing
timing see ENGINE PERFORMANCE
\
\
\
\
\
\
\
Pre-Ignition or Incorrect type of fuel Replace with correct
Melted Electrodes fuel
Incorrect ignition timing Reset ignition timing
see ENGINE PERFORMANCE
Burned valves Replace valves
Engine Overheating Check cooling system
Wrong type of spark plug, Replace with correct
too hot spark plug, see
ENGINE PERFORMANCE
\
\
\
\
\
\
\
Chipped Severe detonation Check for over-
Insulators advanced timing or
combustion
Improper gapping Re-gap spark plugs
procedure
\
\
\
\
\
\
\
Rust Colored Additives in unleaded Try different fuel
Deposits fuel brand
\
\
\
\
\
\
\
Water In Combus- Blown head gasket or Repair or replace
tion Chamber cracked head head or head gasket
\
\
\
\
\
\
\
NOTE: Before diagnosing an electronic ignition system, ensure that
all wiring is connected properly between distributor, wiring
connector and spark plugs. Ignition problem will show up
either as: Engine Will Not Start or Engine Runs Rough.
BASIC ELECTRONIC IGNITION TROUBLE SHOOTING CHARTS
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Engine Won't Open circuit between Repair circuit
Start distributor and bulkhead
connector
Open circuit between Repair circuit
bulkhead connector and
Page 1400 of 1501
![MITSUBISHI MONTERO 1998 Service Manual ignition switch
Open circuit between Repair circuit
ignition switch and
starter solenoid
\](/img/19/57333/w960_57333-1399.png "MITSUBISHI MONTERO 1998 Service Manual ignition switch
Open circuit between Repair circuit
ignition switch and
starter solenoid
\")
ignition switch
Open circuit between Repair circuit
ignition switch and
starter solenoid
\
\
\
\
\
\
\
Engine Runs Fuel lines leaking or Tighten fitting,
Rough clogged remove restriction
Initial timing incorrect Reset ignition timing
see ENGINE PERFORMANCE
Centrifugal advance Repair distributor
malfunction advance
Defective spark plugs or Replace plugs or plug
wiring wiring
\
\
\
\
\
\
\
Component Failure Spark arc-over on cap, Replace cap, rotor or
rotor or coil or coil
Defective pick-up coil Replace pick-up coil
Defective ignition coil Replace ignition coil
Defective vacuum unit Replace vacuum unit
Defective control module Replace control module
\
\
\
\
\
\
\
BASIC ELECTRONIC IGNITION TROUBLE SHOOTING
CHARTS - USING OSCILLOSCOPE PATTERNS
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Firing Voltage Retarded ignition timing Reset ignition
Lines are the Same, timing, see ENGINE
but Abnormally High PERFORMANCE section
Fuel mixture too lean Readjust carburetor,
see ENGINE PERFORMANCE
High resistance in coil Replace coil wire
wire
Corrosion in coil tower Clean and/or replace
terminal coil
Corrosion in distributor Clean and/or replace
coil terminal distributor cap
\
\
\
\
\
\
\
Firing Voltage Fuel mixture too rich Readjust carburetor,
Lines are the Same see ENGINE PERFORMANCE
but Abnormally Low
Breaks in coil wire causing Replace coil wire
arcing
Cracked coil tower causing Replace coil
arcing
Low coil output Replace coil
Low engine compression Determine cause and
Page 1402 of 1501
Worn or dirty needle valve Clean carburetor, see
and seat ENGINE PERFORMANCE
Float sticking Readjust or replace
float see the ENGINE
PERFORMANCE section
Incorrect choke adjustment Reset choke adjustment
see ENGINE PERFORMANCE
Defective coil Replace coil
Improper spark plug gap Regap spark plugs
Incorrect ignition timing Reset ignition timing
see ENGINE PERFORMANCE
\
\
\
\
\
\
\
Detonation Over-advanced ignition Reset ignition timing
timing see ENGINE PERFORMANCE
Defective spark plugs Replace spark plugs
Fuel lines clogged Clean fuel lines
EGR system malfunction Check and repair EGR
system
PCV system malfunction Repair PCV system
Vacuum leaks Check and repair
vacuum system
Loose fan belts Tighten or replace
fan belts, see ENGINE
PERFORMANCE
Restricted airflow Remove restriction
Vacuum advance malfunction Check distributor
operation
\
\
\
\
\
\
\
Dieseling Binding carburetor linkage Eliminate binding
Binding throttle linkage Eliminate blinding
Binding choke linkage or Eliminate binding
fast idle cam
Defective idle solenoid Replace idle solenoid
see ENGINE PERFORMANCE
Improper base idle speed Reset idle speed, see
see ENGINE PERFORMANCE
Incorrect ignition timing Reset ignition timing
see ENGINE PERFORMANCE
Incorrect idle mixture Reset idle mixture,
setting see ENGINE PERFORMANCE
\
\
\
\
\
\
\
Faulty Incorrect ignition timing Reset ignition timing
Acceleration see ENGINE PERFORMANCE
Page 1403 of 1501
Engine cold and choke too Adjust choke and
lean allow engine to warm-
up
Defective spark plugs Replace spark plugs
Defective coil Replace coil
\
\
\
\
\
\
\
Faulty Low Speed Clogged idle transfer slots Clean idle transfer
Operation slots, see FUEL
Restricted idle air bleeds Disassemble and clean
and passages carburetor, see FUEL
Clogged air cleaner Replace air filter
Defective spark plugs Replace spark plugs
Defective ignition wires Replace ignition wire
see ENGINE PERFORMANCE
Defective distributor cap Replace distributor
cap
\
\
\
\
\
\
\
Faulty High Speed Incorrect ignition timing Reset ignition timing
Operation see ENGINE PERFORMANCE
Defective distributor Replace advance
centrifugal advance mechanism
Defective distributor Replace advance unit
vacuum advance
Incorrect spark plugs or Check gap and/or
plug gap replace spark plugs
Faulty choke operation Check choke and
repair as required
Clogged vacuum passages Remove restrictions
Improper size or clogged Check jet size and
main jet clean, see FUEL
Restricted air cleaner Check filter and
replace as necessary
Defective distributor cap, Replace cap, rotor or
rotor or coil coil
\
\
\
\
\
\
\
Misfire at All Defective spark plugs Replace spark plugs
Speeds
Defective spark plug wires Replace spark plug
wires
Defective distributor cap, Replace cap, rotor,
rotor, or coil or coil
Cracked or broken vacuum Replace vacuum hoses
hoses
Page 1404 of 1501
![MITSUBISHI MONTERO 1998 Service Manual Vacuum leaks Repair vacuum leaks
Fuel lines clogged Remove restriction
\
\
\](/img/19/57333/w960_57333-1403.png "MITSUBISHI MONTERO 1998 Service Manual Vacuum leaks Repair vacuum leaks
Fuel lines clogged Remove restriction
\
\
\")
Vacuum leaks Repair vacuum leaks
Fuel lines clogged Remove restriction
\
\
\
\
\
\
\
Hesitation Cracked or broken vacuum Replace vacuum hoses
hoses
Vacuum leaks Repair Vacuum leaks
Binding carburetor linkage Eliminate binding
Binding throttle linkage Eliminate binding
Binding choke linkage or Eliminate binding
fast idle cam
Improper float setting Readjust float
setting, see FUEL
Cracked or broken ignition Replace ignition
wires wires
\
\
\
\
\
\
\
Rough idle, Incorrect curb idle or fast Reset idle speed, see
Missing or idle speed see ENGINE PERFORMANCE
Stalling
Incorrect basic timing Reset ignition timing
see ENGINE PERFORMANCE
Improper idle mixture Reset idle mixture,
adjustment see ENGINE PERFORMANCE
Improper feedback system Check feedback system
operation see ENGINE PERFORMANCE
Incorrect spark plug gap Reset spark plug gap,
see ENGINE PERFORMANCE
Moisture in ignition Dry components
components
Loose or broken ignition Replace ignition
wires wires
Damaged distributor cap or Replace distributor
or rotor cap or rotor
Faulty ignition coil Replace ignition coil
Fuel filter clogged or worn Replace fuel filter
Damaged idle mixture screw Replace idle mixture
screw, see FUEL
Improper fast idle cam Reset fast idle cam
adjustment adjustment, see TUNE-
see ENGINE PERFORMANCE
Improper EGR valve operation Replace EGR valve
Faulty PCV valve air flow Replace PCV valve
Choke binding or improper Reset choke or
choke setting eliminate binding
Page 1405 of 1501
Vacuum leak Repair vacuum leak
Improper float bowl fuel Reset float
level adjustment, see FUEL
Clogged air bleed or idle Clean carburetor
passages passages, see FUEL
Clogged or worn air cleaner Replace air filter
filter
Faulty choke vacuum Replace diaphragm,
diaphragm see ENGINE PERFORMANCE
Exhaust manifold heat valve Replace heat valve
inoperative
Improper distributor spark Check distributor
advance operation
Leaking valves or valve Check and repair
components valvetrain
Improper carburetor Remove and remount
mounting carburetor
Excessive play in Replace distributor
distributor shaft
Loose or corroded wiring Repair or replace as
connections required
\
\
\
\
\
\
\
Engine Surges Improper PCV valve airflow Replace PCV valve
Vacuum leaks Repair vacuum leaks
Clogged air bleeds Remove restriction
EGR valve malfunction Replace EGR valve
Restricted air cleaner Replace air filter
filter
Cracked or broken vacuum Replace vacuum hoses
hoses
Cracked or broken ignition Replace ignition
wires wires
Vacuum advance malfunction Check unit and
replace as necessary
Defective or fouled spark Replace spark plugs
plugs
\
\
\
\
\
\
\
Ping or Spark Incorrect ignition timing Reset ignition timing
Knock see ENGINE PERFORMANCE
Distributor centrifugal or Check operation and
vacuum advance malfunction replace as necessary
Carburetor setting too lean Readjust mixture