ignition MITSUBISHI MONTERO 1998 Service Manual

Check continuity between specified terminals. See Fig. 14. If
continuity is not as specified, replace wiper/washer switch.
MONTERO
Ignition Switch & Key Reminder Switch Tests
Disconnect ignition switch and key reminder switch
connectors. Check continuity between specified terminals. See Figs. 19
and 20. If continuity is not as specified, replace ignition switch or
key reminder switch.
Fig. 19: Exploded View Of Steering Column (Montero)
Courtesy of Mitsubishi Motor Sales of America

Fig. 20: Testing Ignition Switch & Key Reminder Switch (Montero)
Courtesy of Mitsubishi Motor Sales of America
Lighting & Turn Signal Switch Tests
Disconnect steering column combination switch connector.

Ignition Switch Test
Disconnect ignition switch connectors. Check continuity
between specified terminals. See Figs. 25 and 26. If continuity is not
as specified, replace ignition switch.
Fig. 25: Exploded View Of Steering Column (Montero Sport)
Courtesy of Mitsubishi Motor Sales of America

Fig. 26: Testing Ignition Switch (Montero Sport)
Courtesy of Mitsubishi Motor Sales of America
Lighting & Turn Signal Switch Tests
Disconnect steering column combination switch connector.
Check continuity between specified terminals. See Figs. 25 and 27. If
continuity is not as specified, replace steering column combination
switch.

Fig. 32: Testing Lighting, Turn Signal & Dimmer/Passing Switches
(3000GT)
Courtesy of Mitsubishi Motor Sales of America
Ignition Switch & Key Reminder Switch Tests

Disconnect ignition switch and key reminder switch
connectors. Check continuity between specified terminals. See Figs. 31
and 34. If continuity is not as specified, replace ignition switch or
key reminder switch.
Fig. 33: Testing Front Wiper/Washer Switch (3000GT)
Courtesy of Mitsubishi Motor Sales of America

Fig. 34: Testing Ignition Switch & Key Reminder Switch (3000GT)
Courtesy of Mitsubishi Motor Sales of America
Wiper/Washer Switch Test (Front)
Disconnect steering column combination switch connector.

Check continuity between specified terminals. See Figs. 31 and 33. If
continuity is not as specified, replace steering column combination
switch.
REMOVAL & INSTALLATION
* PLEASE READ THIS FIRST *
WARNING: Deactivate air bag system before performing any service
operation. See AIR BAG RESTRAINT SYSTEMS article. DO NOT
apply electrical power to any component on steering column
without first deactivating air bag system. Air bag may
deploy.
IGNITION SWITCH
Removal & Installation (Diamante)
Remove instrument panel lower cover. Remove upper and lower
steering column covers. See Fig. 1. Remove ignition switch. To
install, reverse removal procedure.
Removal & Installation (Eclipse)
1) Remove knee protector mount screw plugs. Remove knee
protector. Remove hood lock release handle. Remove upper and lower
steering column covers. See Fig. 6. Remove ignition key illumination
light.
2) Remove steering lock cylinder. Remove A/C-heater system
lap cooler and shower ducts. On A/T models, remove key interlock cable
and slide lever. On all models, remove ignition switch. To install,
reverse removal procedure.
Removal & Installation (Galant)
Remove knee protector. Remove upper and lower column covers.
See Fig. 11 . Remove ignition switch. To install, reverse removal
procedure.
Removal & Installation (Mirage)
Remove knee protector. Remove steering column cover. See
Fig. 15 . Remove clip and cover. On A/T models, remove key interlock
cable, spring and slide lever. On all models, remove ignition switch.
To install, reverse removal procedure.
Removal & Installation (Montero & Montero Sport)
Remove lower instrument panel cover. Remove upper and lower
column covers. See Fig. 19 or 25. Remove ignition switch. To install,
reverse removal procedure.
Removal & Installation (3000GT)
Remove knee protector. Remove upper and lower steering column
covers. See Fig. 31. Remove A/C-heater system lap cooler duct and foot
duct. Remove key reminder switch. Remove ignition switch. To install,
reverse removal procedure.
STEERING COLUMN SWITCH
CAUTION: DO NOT hammer on steering shaft. Collapsible steering column
mechanism may be damaged.
Removal & Installation (Diamante)
Remove air bag module. See AIR BAG RESTRAINT SYSTEMS article.
Remove steering wheel. Remove instrument panel lower cover. Remove
upper and lower steering column covers. See Fig. 1. Remove steering

STEERING COLUMN
1998 Mitsubishi Montero
1997-98 STEERING
Mitsubishi - Steering Columns - RWD & 4WD
Mitsubishi: Montero, Montero Sport
DESCRIPTION & OPERATION
WARNING: Vehicle is equipped with a Supplemental Restraint System
(SRS) that includes an air bag located in steering wheel.
Use caution when working around steering column. Ensure
battery is disconnected before attempting any repair. DO NOT
apply electrical power to any component on steering column
without disconnecting air bag module (air bag could deploy).
Steering column consists of a collapsible steering shaft with
lower joint assembly. Vehicle is equipped with a Supplemental
Restraint System (SRS) that includes an air bag and clockspring
located in steering column wheel.
NOTE: For information not covered in this article, air bag
DIAGNOSIS & TESTING or DISPOSAL PROCEDURES, see AIR BAG
RESTRAINT SYSTEM article.
DISABLING & ACTIVATING AIR BAG SYSTEM
WARNING: Wait at least 60 seconds after disconnecting negative
battery cable before servicing SRS. System reserve capacitor
maintains SRS voltage for about 60 seconds after battery is
disconnected. Servicing SRS before 60-second period may
cause accidental air bag deployment and possible personal
injury.
To disable system, turn ignition switch to OFF position.
Disconnect and isolate negative battery cable end. Wait at least 60
seconds. To activate system, reconnect negative battery cable.
AIR BAG SERVICE PRECAUTIONS
The following precautions should be observed when working
with SRS:
* Disable SRS before servicing any SRS or steering column
component. Failure to do this may result in accidental air
bag deployment and possible personal injury. See DISABLING &
ACTIVATING AIR BAG SYSTEM.
* Wait at least 60 SECONDS after disabling air bag system. SRS
system retains enough voltage, for a short time after system
is disabled, to deploy air bag.
* After repairs, always turn ignition on to ensure SRS warning
light is working properly and no system faults are indicated.
* Always wear safety glasses when servicing or handling an air
bag.
* DO NOT expose air bag module and clockspring to temperatures
more than 200
F (93C).
* When placing a live air bag on a bench or other surface,
always face air bag and trim cover up, away from surface.
This will reduce motion of module if air bag accidentally

IGNITION SWITCH
Removal & Installation
1) Remove upper and lower steering column covers. Disconnect
harness connector from ignition switch. Using hacksaw, cut slots in
bolt heads of lock assembly. Using screwdriver, remove bolts and lock
assembly.
2) To install, reverse removal procedure. Tighten new bolts
until heads of bolts sheer off.
STEERING COLUMN
WARNING: Failure to follow air bag service precautions may result in
air bag deployment and personal injury. See AIR BAG SERVICE
PRECAUTIONS. Follow all service precautions before
attempting repairs. After component replacement, perform a
system operational check to ensure proper system operation.
CAUTION: Applying excessive pressure or causing impact to steering
shaft during service may cause column to collapse. Before
removing steering column, ensure wheels are in
straight-ahead position. Note steering wheel location for
installation reference.
Removal
1) Remove steering wheel. Remove combination switch and
ignition switch (if necessary). See STEERING WHEEL under
REMOVAL & INSTALLATION .
2) Remove lower instrument panel cover and air duct.
Disconnect all electrical connections. Disconnect brake pedal return
spring (if equipped). Disconnect gearshift control cable.
3) Remove bolts for dust cover at firewall. Remove bolt from
clamp at steering gear. Remove steering column bolts and remove
steering column.
Installation
To install, reverse removal procedure. Apply sealant (3M ATD
8663) to dust cover bolts before installing. Tighten bolts to
specification. See TORQUE SPECIFICATIONS .
OVERHAUL
STEERING COLUMN
WARNING: Failure to follow air bag service precautions may result in
air bag deployment and personal injury. See AIR BAG SERVICE
PRECAUTIONS. Follow all service precautions before
attempting repairs. After component replacement, perform a
system operational check to ensure proper system operation.
NOTE: Vehicle steering column is not repairable. See below for
joint assembly and steering lock removal and installation.
Disassembly
Remove steering column from vehicle. See STEERING COLUMN
under REMOVAL & INSTALLATION . Remove clamp bolt from joint assembly.
See Fig. 1 . Remove assembly. Remove lower boot, upper boot and dust
cover from joint assembly. To remove steering lock, use a hacksaw to
cut bolts at steering lock bracket side. Remove steering lock and
bracket.