oil MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 1189 of 1501
Stud loose in
taper hole ............. A ........... (7) Require repair or
replacement.
Taper hole elongated .... A ........ ( 8) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications .......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 6) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 7) - Check for damaged taper hole.
( 8) - Check for damaged stud.
\
\
\
\
\
\
\
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
You are not required to replace shocks or struts in axle
sets. However, when replacing a shock or strut due to the conditions
that follow, you may suggest replacement of the other shock or strut
on the same axle for improved performance and preventive maintenance.
* Part is close to the end of its useful life
* To extend tire life
* To balance ride and handling
* To improve stopping distance
When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check and adjust
alignment as needed. Refer to the OEM specifications.
Under no circumstances should a technician bend struts or
strut housings.
A vehicle's load-carrying and handling abilities are limited
by its suspension, tires, brakes, and driveline. Installing coil over
shocks or any other load assist device does not increase the vehicle's
load capacity. See the vehicle owner's manual for more details.
NOTE: If vehicle is equipped with original equipment coil over
shocks, apply the conditions for coil springs from the
SPRINGS - COIL, LEAF AND TORSION BAR section of the
STEERING AND SUSPENSION guidelines. If the vehicle is
equipped with add-on coil over shocks, you may suggest
replacing the shocks with standard shocks for any spring-
related condition.
SHOCK ABSORBER, STRUT CARTRIDGE AND STRUT ASSEMBLY INSPECTION
\
\
\
\
\
\
\
Page 1191 of 1501
Dust boot (bellows)
missing ................ 2 ......... (2) Suggest replacement
of boot.
Dust boot (bellows)
torn ................... 2 ......... ( 2) Suggest replacement
of boot.
Dust shield broken ...... 2 ........ ( 2) Suggest replacement.
Dust shield missing ..... 2 ........ ( 2) Suggest replacement.
Gland nut (strut housing
cap) is not removable
using appropriate tool . A .. ( 3) Require replacement of nut
and/or housing.
Gland nut (strut housing
cap) threads damaged ... A ... Require repair or replacement
of nut.
Gland nut (strut housing
cap) threads stripped
(threads missing) ...... A ..... Require replacement of nut.
Housing dented .......... A .......... ( 1) Further inspection
required.
Housing punctured ....... A ............ Require replacement.
Jounce bumper missing ... C ... Require replacement of jounce
bumper.
Jounce bumper split ..... 1 ... Suggest replacement of jounce
bumper.
Leaking oil, enough for
fluid to be running down
the body ............... A ........ ( 4) Require replacement.
Noise ................... 2 .......... ( 5) Further inspection
required.
Piston rod bent ......... A ............ Require replacement.
Piston rod broken ....... A ............ Require replacement.
Piston rod has surface
defect ................. 2 ............ Suggest replacement.
Piston rod threads
damaged ................ A .. Require repair or replacement.
Piston rod threads
stripped (threads
missing) ............... A ............ Require replacement.
Seized .................. A ............ Require replacement.
Shock missing ........... C ............ Require replacement.
Strut housing bent ...... A ............ Require replacement.
Strut housing cap (gland
nut) is not removable
using appropriate tool . A ......... ( 3) Require replacement
of nut and/or housing.
Strut housing cap (gland
nut) threads damaged ... A ... Require repair or replacement
of nut.
Strut housing cap (gland
nut) threads stripped
(threads missing) ...... A ..... Require replacement of nut.
Strut housing severely
corroded, affecting
structural integrity ... A ............ Require replacement.
Strut housing threads
damaged ................ A .. Require repair or replacement.
Strut housing threads
stripped (threads
missing) ............... A ............ Require replacement.
Tire cupping ............ A .......... ( 6) Further inspection
required.
Page 1192 of 1501
(1) - Require replacement of units where dents restrict shock
or strut piston rod movement. If dents don't restrict
movement, no service is suggested or required. Especially
critical on mono-tube shocks.
( 2) - This condition can lead to damage of the piston rod,
which, in turn, causes premature piston rod seal wear.
( 3) - Only required if replacing cartridge.
( 4) - CAUTION: If the strut cartridge has been replaced previously,
the oil on the strut housing may be filler oil. The
technician must identify the source of the oil.
( 5) - If noise is isolated to shock or strut, suggest
replacement.
( 6) - Although shocks or struts may have contributed to tire
cupping, an inspection is needed of the entire suspension
system. If the shock or strut is found to be contributing
to the tire cupping, require replacement.
\
\
\
\
\
\
\
SPINDLES
SPINDLE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Race seat area
undersized ............. B ............ Require replacement.
Scored .................. A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\
SPRINGS - COIL, LEAF AND TORSION BAR
When springs are replaced, it is suggested, but not required,
that both springs on an axle be replaced to maintain equal height from
side to side and to provide a balanced ride and proper handling.
When variable rate springs are installed in place of
conventional coil springs, they must be installed in axle sets to
ensure proper handling, uniform ride, and proper chassis height.
Erroneous height measurements may result from: improper tire
inflation, non-standard tire or wheel size, and heavy load in vehicle
or trunk.
SPRING (COIL, LEAF AND TORSION BAR) INSPECTION
Page 1193 of 1501
![MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
Condition Code](/img/19/57333/w960_57333-1192.png "MITSUBISHI MONTERO 1998 Service Manual \
\
\
\
\
\
\
Condition Code")
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
bent .................. B .... Require repair or replacement
of bent part.
Attaching hardware
broken ................ A .... Require replacement of broken
part.
Attaching hardware
corroded, affecting
structural integrity .. A .. Require replacement of corroded
part.
Attaching hardware
incorrect ............. A ........... Require replacement of
incorrect part.
Attaching hardware
loose ................. A .... Require repair or replacement
of loose part.
Attaching hardware
missing ............... C ... Require replacement of missing
part.
Attaching hardware
threads damaged ....... A .... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ..... A ...... Require replacement of part
with stripped threads.
Broken (all springs
except secondary
leave(s) on multi-leaf
springs) .............. A ............. Require replacement.
Coil clash ............. .. .. (1) Require ride height check.
Coil spring insulator
deteriorated .......... 2 ........... Suggest replacement of
insulator.
Coil spring insulator
missing ............... 2 ........... Suggest replacement of
insulator.
Coil spring insulator
split ................. 2 ........... Suggest replacement of
insulator.
Coil spring plastic
coating deteriorated -
rust present .......... A ...... ( 2) Refer to manufacturer's
service requirements.
Composite spring
damaged ............... .. .......... ( 3) Further inspection
required.
Cracked (all springs
except composite leaf and
secondary leave(s) on
multi-leaf springs) ... A ............. Require replacement.
Installed incorrectly .. B .................. Require repair.
Leaf spring insulators
missing ............... 2 ........... Suggest replacement of
insulators.
Secondary leaf on multi-
leaf spring broken .... 1 .... Suggest repair or replacement
Secondary leaf on multi-
leaf spring cracked ... 1 .... Suggest repair or replacement
Torsion bar
Page 1196 of 1501
replace steering damper.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
part, if available; otherwise,
replace steering damper.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace steering
damper.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace steering
damper.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace steering damper.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace steering damper.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
steering damper.
Binding ................. A ............ Require replacement.
Damper body dented ...... A .......... (1) Further inspection
required.
Damper body punctured ... A ............ Require replacement.
Damping (none) .......... A ............ Require replacement.
Dust boot (bellows)
missing ................ 2 ......... ( 2) Suggest replacement
of boot.
Dust boot (bellows)
split .................. 2 ......... ( 2) Suggest replacement
of boot.
Dust shield broken ...... 2 ........ ( 2) Suggest replacement.
Dust shield missing ..... 2 ........ ( 2) Suggest replacement.
Leaking oil, enough for
fluid to be running
down the body .......... A ............ Require replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Noise ................... 2 .......... ( 3) Further inspection
required.
Piston rod bent ......... A ............ Require replacement.
Piston rod broken ....... A ............ Require replacement.
Piston rod has surface
defect ................. 2 ............ Suggest replacement.
Piston rod threads
stripped (threads
missing) ............... A ............ Require replacement.
Piston rod threads
damaged ................ A .. Require repair or replacement.
Seized .................. A ............ Require replacement.
( 1) - Require replacement of units where dents restrict damper
Page 1236 of 1501
Removal
Raise and support vehicle. Remove wheel assembly. Remove hub
cap. Remove snap ring and shim. Remove drive flange. Remove brake
caliper and suspend with wire. On vehicles with ABS, remove ABS speed
sensor. On all models, remove lock washer. Remove lock nut using
Socket (MB990954). See Fig. 2. Remove front rotor and hub assembly.
Installation
To install, reverse removal procedure. Adjust wheel bearing
preload and check drive shaft endplay. See ADJUSTMENTS.
Fig. 2: Exploded View Of Hub Assembly (Montero Sport Shown, Montero
Similar)
Courtesy of Mitsubishi Motor Sales of America.
STEERING KNUCKLE
Removal
1) Raise and support vehicle. Remove wheel assembly. Remove
brake caliper. Remove axle hub assembly. See AXLE HUB ASSEMBLY under
REMOVAL & INSTALLATION . Remove brake dust cover from steering knuckle.
If equipped with ABS, remove ABS speed sensor.
2) On all models, disconnect tie rod end from steering
knuckle. Mark torsion bar adjusting nut for installation reference.
Loosen torsion bar anchor arm assembly adjusting nut. Loosen, but DO
NOT remove, ball joint-to-steering knuckle nuts.
3) Using Steering Linkage Puller (MB991406), separate ball
joints from steering knuckle. Detach upper and lower ball joints from
steering knuckle. Remove steering knuckle from axle shaft. Remove oil
Page 1242 of 1501
SUSPENSION - REAR
1998 Mitsubishi Montero
1997-98 SUSPENSION
Rear - RWD & 4WD
Montero, Montero Sport
DESCRIPTION
NOTE: For testing and diagnosis information on electronically
controlled shocks, see ELECTRONIC - Montero article.
Montero
Rear suspension system is multi-link type with shock
absorbers, coil springs, lateral rod and stabilizer bar. See Fig. 2.
Montero Sport
Rear suspension system is a leaf spring type with shock
absorbers and stabilizer bar. See Fig. 2.
Fig. 1: Exploded View Of Rear Suspension (Montero Sport)
Courtesy of Mitsubishi Motor Sales of America.
Page 1244 of 1501
REAR SUSPENSION ASSEMBLY
NOTE: Procedures for Montero are for lateral rod, coil springs and
lower arms only. Procedures for Montero Sport are for leaf
springs only.
Removal (Montero)
1) Raise and support rear of vehicle. Place a jack under
center of rear axle housing. Remove parking brake cable attaching
bolts.
2) Remove rear speed sensor attaching bolt (if equipped).
Remove rear axle housing lock position harness attaching bolt and
lower shock bolts.
3) Remove lateral rod bolts and remove lateral rod. Remove
lower arm rear bolts. Remove lower arm front mounting nut and remove
lower arm. See Fig. 2.
Inspection
Check lateral rod for straightness and damage. Check rubber
bushings for deterioration, cracks and wear.
Installation
If lateral rod bushings need replacing, remove and install
using Lower Arm Bushing Arbor (MB990650). Apply a sufficient amount of\
liquid soap to bushings when installing them into lateral rod. If
lower arm rear bushings need replacing, remove and install rear
bushings using Rear Bushing Arbor (MB991293). To complete
installation, reverse removal procedure. Tighten all suspension
fasteners to specification with vehicle on ground and suspension
unloaded. See TORQUE SPECIFICATIONS .
Removal (Montero Sport)
1) Raise and support rear of vehicle. Place a jack under
center of rear axle housing.
2) Disconnect parking brake cable attaching bolts. Remove
rear speed sensor attaching bolt. Remove rear shock nuts and washers.
Remove rear shocks.
NOTE: The yellow shock mounts on left side and the pink one mounts
to the right side of vehicle.
3) Remove U-bolt nuts, U-bolt seat and U-bolts. Remove bump
stopper. Remove rear shackle plate nuts, shackle plate, bushings and
shackle assembly. Remove front shackle nuts and bolts. Remove leaf
spring. See Fig. 1.
Inspection
Check leaf springs for cracks and other damage. Inspect all
components and bushings for damage and wear. Replace components as
necessary.
Installation
To install, reverse removal procedure. Ensure shocks are
installed on proper side of vehicle. Tighten all suspension fasteners
to specification with vehicle on ground and suspension unloaded. See
TORQUE SPECIFICATIONS .
SHOCKS
Removal
1) Raise and support rear of vehicle. Place a jack under
center of rear axle housing. On Montero remove shock actuator (if
equipped).
Page 1245 of 1501
2) Remove upper shock mounting nuts and washers. On Montero
remove shock lower mounting nuts and bolts. On Montero Sport remove
shock lower mounting nuts and washers. Remove shock assembly.
Inspection
Check shock for oil leakage, abnormal noise and poor
function. Check coil spring for bending and weakness. Check rubber
parts for deterioration and cracks.
Installation
To install, reverse removal procedure. Tighten all fasteners
to specification. See TORQUE SPECIFICATIONS.
STABILIZER BAR
Removal
Raise and support vehicle. Support rear suspension assembly
using a jack. On Montero remove shock lower mounting bolts and nuts.
Remove stabilizer bar bracket and bushings. Remove stabilizer link
mounting nut and bolt. Remove stabilizer link joint cups, bushings and
collar. Remove stabilizer bar.
Inspection
1) Check bushings for wear and deterioration. Check
stabilizer bar, stabilizer link and all bolts for damage and wear.
Replace components as necessary.
Installation
To install, reverse removal procedure. When installing
stabilizer link, hold link using wrench and tighten nut until distance
from end of bolt to edge of nut is .59-.70" (15-17 mm). Tighten all
fasteners to specification. See TORQUE SPECIFICATIONS.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\
Application Ft. Lbs. (N.m)\
Upper Shock Nut
Montero .................................................. 11 (15)\
Montero Sport ............................................ 16 (22)\
Lower Shock Nut And Bolt
Montero ........................................ 159-181 (216-245)\
Montero Sport ............................................ 16 (22)\
Lateral Rod Nut And Bolt
Montero ................................................. 170 (230)\
Lower Arm Rear Nut And Bolt
Montero ................................................. 170 (230)\
Lower Arm Front Nut
Montero ................................................. 101 (137)\
Leaf Spring Rear Shackle Nut
Montero Sport ............................................. 38 (52)\
Leaf Spring Front Shackle Nut And Bolt
Montero Sport ........................................... 145 (196)\
"U" Bolt Nut
Montero Sport ...................................... 72-87 (98-118)\
Stabilizer Bar Bracket Bolt .......................... 25-26 (34-35)\
\
\
\
\
\
\
\
Page 1246 of 1501
* SUSPENSION UNIFORM INSPECTION GUIDELINES *
1998 Mitsubishi Montero
GENERAL INFORMATION
Steering, Suspension, Wheel Alignment, Wheels and Tires
Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
Motorist Assurance Program (MAP)
OVERVIEW
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
Steering and Suspension
AIR RIDE SUSPENSION
AIR RIDE SUSPENSION - AIR SHOCKS AND AIR STRUTS
AIR RIDE SUSPENSION - AIR SPRING VALVES
AIR RIDE SUSPENSION - AIR SPRINGS
AIR RIDE SUSPENSION - COMPRESSORS
AIR RIDE SUSPENSION - HEIGHT SENSORS
AIR RIDE SUSPENSION - MODULES
AIR RIDE SUSPENSION - RELAYS (COMPRESSOR)
AIR RIDE SUSPENSION - SWITCHES (ON/OFF)
AIR RIDE SUSPENSION - TORSION SPRINGS (COUNTER BALANCING)
AIR RIDE SUSPENSION - TUBING
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SUSPENSION - WIRING HARNESSES
BALL JOINTS
BUSHINGS
CENTER LINKS
CONTROL ARM SHAFTS
CONTROL ARMS
DRAG LINKS
ELECTRONIC RIDE CONTROL SHOCKS AND STRUTS
IDLER ARMS
KING PINS
PITMAN ARMS
POWER STEERING HOSES
POWER STEERING (HYDRAULIC) PUMPS
RADIUS ARMS
RELAY RODS
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
SPINDLES
SPRINGS - COIL, LEAF AND TORSION BAR
STEEL POWER STEERING LINES
STEERING ARMS
STEERING DAMPERS
STEERING GEARS (EXCEPT RACK AND PINION)
STEERING GEARS - RACK AND PINION
STEERING KNUCKLES
STRIKE OUT BUMPERS
STRUT RODS
STRUT UPPER BEARING PLATE ASSEMBLIES
SWAY BAR LINKS
SWAY BARS