lock MITSUBISHI MONTERO 1998 Service Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 1998, Model line: MONTERO, Model: MITSUBISHI MONTERO 1998Pages: 1501, PDF Size: 25.81 MB
Page 1311 of 1501
Differential Lock Circuit
COMPUTER DATA LINES
Page 1336 of 1501
Power Distribution Circuit (2 of 2)
POWER DOOR LOCKS
Page 1337 of 1501
Power Door Lock Circuit, W/ Keyless Entry
Page 1338 of 1501
Power Door Lock Circuit, W/O Keyless Entry
POWER MIRRORS
Page 1349 of 1501
Rear Differential Lock Circuit
WARNING SYSTEMS
Page 1355 of 1501
and remove. Disconnect all external solenoid and switch connections.
3) On Montero 4WD, remove catalytic converter and front
exhaust pipe. On all models, disconnect speedometer cable and control
cables at transmission. Remove starter and bellhousing cover. Place
reference mark on torque converter and drive plate for reassembly
reference. Remove torque converter bolts. Push torque converter back
and away from drive plate.
4) Disconnect transmission cooler lines. Remove oil filler
tube. Secure transmission on a jack. Raise transmission slightly to
take weight off mount. Remove crossmember-to-mount bolts and
crossmember.
5) Remove transfer case mounting bracket and mount (if
equipped). Remove transmission-to-engine mounting bolts. Carefully
lower transmission from vehicle.
CAUTION: Ensure torque converter is fully seated in transmission
before installation.
Installation
1) To install, reverse removal procedure. Tighten
transmission-to-engine bolts and torque converter-to-drive plate bolts
to specification. See TORQUE SPECIFICATIONS. Tighten mount bolts with
weight of engine and transmission on mounts. Ensure reference marks on
drive shaft(s) and torque converter-to-drive plate are matched.
2) Apply sealant to transfer case gearshift assembly gasket
before installation. Coat transmission oil filler tube "O" ring with
transmission fluid before installation. Refill transmission fluid to
specified level. See LUBRICATION in TRANSMISSION SERVICING - A/T
article. Adjust all control cables. See ADJUSTMENTS in
TRANSMISSION SERVICING - A/T article.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS - FWD MODELS \
\
\
\
\
\
\
Applications Ft. Lbs. (N.m)\
Ball Joint Nut ............................................ 74 (100)\
Center Crossmember Assembly Front Bolt ..................... 69 (93)\
Center Crossmember Assembly Rear Bolt ...................... 52 (70)\
Starter Bolts .............................................. 22 (30)\
Tie Rod End Nut ............................................ 21 (28)\
Torque Converter-To-Drive Plate Bolt ................. 33-38 (45-52)\
Transaxle-To-Engine Block Bolt
8-mm Bolt .................................................... ( 1)
10-mm Bolt ......................................... 22-25 (30-34)\
12-mm Bolt ......................................... 31-40 (42-54)\
Upper Coupling Bolts
2.4L ..................................................... 35 (48)\
3.0L ..................................................... 54 (73)\
Lower Coupling Bolts
2.4L ..................................................... 35 (48)\
3.0L ..................................................... 65 (88)\
( 1) - Tighten to 84-108 INCH lbs. (10-12 N.m).
\
\
\
\
\
\
\
TORQUE SPECIFICATIONS - RWD MODELS \
\
\
\
\
\
\
Applications Ft. Lbs. (N.m)\
Engine-To-Transmission Bolt ................................ 65 (88)\
Page 1356 of 1501
![MITSUBISHI MONTERO 1998 Service Manual Torque Converter-To-Drive Plate Bolt ....................... 30 (41)\
Transmission-To-Engine Block Bolt .......................... 55 (74)\
\
\](/img/19/57333/w960_57333-1355.png "MITSUBISHI MONTERO 1998 Service Manual Torque Converter-To-Drive Plate Bolt ....................... 30 (41)\
Transmission-To-Engine Block Bolt .......................... 55 (74)\
\
\")
Torque Converter-To-Drive Plate Bolt ....................... 30 (41)\
Transmission-To-Engine Block Bolt .......................... 55 (74)\
\
\
\
\
\
\
\
Page 1359 of 1501
removed to drain fluid. Remove oil filter/screen if necessary.
2) If oil filter/screen is replaced, tighten bolts to
specification. See TORQUE SPECIFICATIONS . Clean oil pan, replace
gasket, and install oil pan. Tighten oil pan bolts and drain plug to
specification. See TORQUE SPECIFICATIONS . Ensure dipstick hole area is
clean. Fill transmission with Dexron-II ATF, through filler tube,
until COLD level is reached on dipstick. Start engine, and allow to
idle for 2 minutes.
3) Shift transmission into each position, ending in Neutral.
Check fluid level with engine running at idle. If necessary, add
sufficient fluid to bring level to lower mark of dipstick. Recheck
fluid level after transmission is at normal operating temperature.
Transfer Case
Drain plug is located on bottom of transfer case. Change
drain plug gasket whenever fluid is changed. Lubricant level should be
at bottom of fill hole on side of transfer case.
ADJUSTMENTS
KICKDOWN SERVO
Eclipse, Galant & 3000 GT
1) Remove all dirt and grease around kickdown servo switch.
Remove snap ring and kickdown servo switch.
2) To prevent servo piston from turning, install Adapter
(MD998915) and Kickdown Servo Wrench (MD998918) so tab of wrench
engages with notch of piston. See Fig. 1.
CAUTION: DO NOT push servo piston inward while installing adapter and
servo wrench. Install adapter in brake pressure port by hand
ONLY. DO NOT use wrench to tighten adapter.
Fig. 1: Adjusting Kickdown Servo (Eclipse, Galant & 3000 GT)
Courtesy of Mitsubishi Motor Sales of America.
3) Loosen lock nut to "V" channel of adjuster rod. Tighten
inner section of Kickdown Service Adjustment Assembly (MD998916) until\
Page 1360 of 1501
it contacts lock nut. See Fig. 1.
4) Install outer section of kickdown service adjustment
assembly on lock nut. Rotate outer section to left and inner section
to right to contact lock nut with inner section.
5) Using an INCH-lb. torque wrench on inner section, tighten
inner section to 89 INCH lbs. (10 N.m), and then loosen inner section.\
Tighten inner section to 44 INCH lbs. (5 N.m).
CAUTION: Before tightening lock nut with torque wrench, tighten it by
hand until it contacts piston. If torque wrench is used
initially, lock nut and adjustment rod may rotate together.
6) Back off outer section 2-2 1/4 turns. Rotate outer section
to right and inner section to left until inner section is free of lock
nut. Tighten lock nut by hand until it contacts piston. Using torque
wrench, tighten lock nut to 18-23 ft. lbs. (25-32 N.m).
7) Remove adapter and kickdown servo wrench. Install new "O"
ring in groove around switch. Install switch and snap ring.
SHIFT LINKAGE
Except Montero
1) Ensure shift and transaxle/transmission levers are both in
Neutral position. Loosen adjusting nut on control cable. See Fig. 2.
Loosen park/neutral position switch body bolts. Rotate park/neutral
position switch until hole in end of transmission manual control lever
is aligned with hole (cross section A-A) in flange of park/neutral
position switch body. Tighten park/neutral position switch body bolts.
Ensure holes in park/neutral position switch flange and transmission
manual control lever stay aligned.
2) Gently pull control cable from dust cover. Make sure shift
lever is still in Neutral. Tighten adjusting nut. Check
transaxle/transmission operation through all ranges. Readjust control
cable if necessary.
Fig. 2: Adjusting Shift Cable (Except Montero)
Courtesy of Mitsubishi Motor Sales of America.
Montero
Ensure shift and transmission levers are both in Neutral
Page 1362 of 1501
Fig. 4: Adjusting Shift Lever Sleeve (Eclipse & Galant)
Courtesy of Mitsubishi Motor Sales of America.
NEUTRAL SAFETY SWITCH
All Models
Neutral safety switch is adjusted along with shift linkage.
See SHIFT LINKAGE .
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS \
\
\
\
\
\
\
Application Ft. Lbs. (N.m)\
Drain Plug
Transaxle/Transmission
Except Montero ................................... 22-25 (30-35)\
Montero .......................................... 13-17 (18-24)\
Transfer Case ............................................ 24 (32)\
Rear Cover ................................................. 17 (23)\
INCH Lbs. (N.m)
Kickdown Servo Lock Nut ................................... 121 (29)\
Oil Filter/Screen Bolt
Except Montero ................................... 48-60 (5.4-6.8)\
Montero ................................................. 61 (6.9)\
Oil Pan Bolt
Except Montero ................................. 84-108 (9.5-12.2)\
Montero ................................................. 69 (7.8)\
Park/Neutral Switch Mounting Bolt (Except Montero) ......... 97 (11\
)
Park/Neutral Switch Mounting Bolt (Montero) ............... 115 (13\
)
Transmission Control Cable Adjusting Nut ................... 115 (13)\
Valve Body Cover ........................................... 97 (11)\