reset MITSUBISHI MONTERO 1998 Owner's Manual

Vacuum leaks Repair vacuum leaks
Fuel lines clogged Remove restriction









\









\









\









\









\









\









\







Hesitation Cracked or broken vacuum Replace vacuum hoses
hoses
Vacuum leaks Repair Vacuum leaks
Binding carburetor linkage Eliminate binding
Binding throttle linkage Eliminate binding
Binding choke linkage or Eliminate binding
fast idle cam
Improper float setting Readjust float
setting, see FUEL
Cracked or broken ignition Replace ignition
wires wires









\









\









\









\









\









\









\







Rough idle, Incorrect curb idle or fast Reset idle speed, see
Missing or idle speed see ENGINE PERFORMANCE
Stalling
Incorrect basic timing Reset ignition timing
see ENGINE PERFORMANCE
Improper idle mixture Reset idle mixture,
adjustment see ENGINE PERFORMANCE
Improper feedback system Check feedback system
operation see ENGINE PERFORMANCE
Incorrect spark plug gap Reset spark plug gap,
see ENGINE PERFORMANCE
Moisture in ignition Dry components
components
Loose or broken ignition Replace ignition
wires wires
Damaged distributor cap or Replace distributor
or rotor cap or rotor
Faulty ignition coil Replace ignition coil
Fuel filter clogged or worn Replace fuel filter
Damaged idle mixture screw Replace idle mixture
screw, see FUEL
Improper fast idle cam Reset fast idle cam
adjustment adjustment, see TUNE-
see ENGINE PERFORMANCE
Improper EGR valve operation Replace EGR valve
Faulty PCV valve air flow Replace PCV valve
Choke binding or improper Reset choke or
choke setting eliminate binding

Vacuum leak Repair vacuum leak
Improper float bowl fuel Reset float
level adjustment, see FUEL
Clogged air bleed or idle Clean carburetor
passages passages, see FUEL
Clogged or worn air cleaner Replace air filter
filter
Faulty choke vacuum Replace diaphragm,
diaphragm see ENGINE PERFORMANCE
Exhaust manifold heat valve Replace heat valve
inoperative
Improper distributor spark Check distributor
advance operation
Leaking valves or valve Check and repair
components valvetrain
Improper carburetor Remove and remount
mounting carburetor
Excessive play in Replace distributor
distributor shaft
Loose or corroded wiring Repair or replace as
connections required









\









\









\









\









\









\









\







Engine Surges Improper PCV valve airflow Replace PCV valve
Vacuum leaks Repair vacuum leaks
Clogged air bleeds Remove restriction
EGR valve malfunction Replace EGR valve
Restricted air cleaner Replace air filter
filter
Cracked or broken vacuum Replace vacuum hoses
hoses
Cracked or broken ignition Replace ignition
wires wires
Vacuum advance malfunction Check unit and
replace as necessary
Defective or fouled spark Replace spark plugs
plugs









\









\









\









\









\









\









\







Ping or Spark Incorrect ignition timing Reset ignition timing
Knock see ENGINE PERFORMANCE
Distributor centrifugal or Check operation and
vacuum advance malfunction replace as necessary
Carburetor setting too lean Readjust mixture

times by increasing injector pulse width accordingly.
NOTE: Never apply battery voltage directly across a low resistance
injector. This will cause injector damage from solenoid coil
overheating.
Fig. 1: Injector Driver Types - Current and Voltage
CURRENT CONTROLLED CIRCUIT ("PEAK & HOLD")
The current controlled driver inside the computer is more
complex than a voltage controlled driver because as the name implies,
it has to limit current flow in addition to its ON-OFF switching
function. Recall, this driver typically requires injector circuits
with a total leg resistance of less than 12 ohms.
Once the driver is turned ON, it will not limit current flow
until enough time has passed for the injector pintle to open. This
period is preset by the particular manufacturer/system based on the
amount of current flow needed to open their injector. This is
typically between two and six amps. Some manufacturers refer to this

WHEEL ALIGNMENT PROCEDURES
CAMBER ADJUSTMENT
Except Montero, Montero Sport & 3000GT
Camber is preset and cannot be adjusted. Check camber. See
appropriate table under WHEEL ALIGNMENT SPECIFICATIONS . If camber is
not within specification, replace damaged or bent parts.
Montero & Montero Sport
1) Check camber. See appropriate table under
WHEEL ALIGNMENT SPECIFICATIONS . If camber is not within specification,
remove shock absorber mounting nut and lock nut.
CAUTION: Difference in shim thickness between front and rear must not
exceed 0.16" (4.0 mm). DO NOT use more than 3 shims at
onelocation.
2) Compress shock absorber, and loosen upper arm mounting
bolts and nuts. Adjust camber by increasing or decreasing shims
between upper arm shaft and crossmember. See Fig. 6.
Fig. 6: Adjusting Camber & Caster (Montero Sport Shown; Montero Is
Similar)
Courtesy of Mitsubishi Motor Sales of America.
3000GT
Check camber. See WHEEL ALIGNMENT SPECIFICATIONS (3000GT)
table. If camber is not within specification, loosen eccentric cam
nut. Rotate eccentric cam bolt to obtain correct camber. See Fig. 7.
Each marking represents a change of .12-.25 degree of camber.