battery MITSUBISHI MONTERO 1998 Owner's Guide

specified, bleed system and inspect hydraulic and clutch components.
See CLUTCH PEDAL SPECIFICATIONS table.
CLUTCH PEDAL INTERLOCK SWITCH
1) Place transmission in Neutral and apply parking brake.
Turn ignition switch to START position with clutch pedal not
depressed. Engine should not crank. If engine cranks, adjust or
replace interlock switch.
2) Disconnect interlock switch connector. Interlock switch
connector is located at clutch pedal. Depress and release interlock
switch. Using ohmmeter, check continuity between interlock switch
terminals. If continuity exists with interlock switch depressed and
does not exist with switch released, switch is okay. Adjust or replace
as necessary.
REMOVAL & INSTALLATION
CLUTCH ASSEMBLY
Removal (2WD Models)
1) Disconnect negative battery cable. Remove shift knob, dust
cover retaining plate, gaskets, stopper plate and control lever
assembly. Raise and support vehicle.
2) Remove front exhaust pipe. Drain transmission fluid. Index
mark drive shaft flange and remove drive shaft.
3) Disconnect back-up light switch connector, speedometer
cable connection and exhaust pipe mounting bracket. Remove lower
bellhousing cover. Disconnect clutch cable from clutch lever.
4) Support transmission with jack. Remove rear engine mount
nuts and bolts from transmission. Remove crossmember with rear engine
mount. Remove remaining bellhousing bolts, move transmission toward
rear and lower from vehicle.
5) If reusing pressure plate, index mark pressure plate to
flywheel for installation reference. Install a clutch alignment tool
to prevent pressure plate and clutch disc from dropping. Loosen
pressure plate bolts gradually in a crisscross pattern to avoid
warping pressure plate flange during removal. Remove pressure plate
and clutch disc. See Fig. 3.
Inspection
1) Check release bearing and release fork for damage or wear.
DO NOT clean release bearing assembly in solvent.
2) Inspect pressure plate surface for wear, cracks, and/or
discoloration. Measure diaphragm spring ends for wear and uneven
height. Replace assembly if height difference between fingers exceeds
.02" (.5 mm).
3) Check facing of clutch disc for loose rivets, uneven
contact, deterioration, seizure or oil saturation. Measure distance
from clutch disc surface to head of rivet. Replace clutch disc if
distance is less than .012" (.30 mm). Replace worn or defective
components as necessary. See Fig. 4.
CAUTION: Install clutch disc with manufacturer's stamp mark (located
near hub of clutch disc) toward pressure plate.
Installation
1) Using a clutch alignment tool, install pressure plate and
clutch disc. If reusing pressure plate, ensure index marks are
aligned. Tighten bolts evenly in a crisscross pattern to
specification. See TORQUE SPECIFICATIONS . See Fig. 3.
2) Clean release bearing sliding surface. DO NOT clean

COMPUTER RELEARN PROCEDURES
1998 Mitsubishi Montero
GENERAL INFORMATION
Computer Relearn Procedures
All Models
* PLEASE READ THIS FIRST *
The following general procedures are to be used if
driveability problems are encountered after power loss or battery has
been disconnected. These procedures may provide an aid in eliminating
these problems.
To reduce the possibility of complaints, after any service
which requires battery power to be disconnected, vehicle should be
road tested.
COMPUTER RELEARN PROCEDURES
Vehicles equipped with engine or transmission computers may
require a relearn procedure after vehicle battery is disconnected.
Many vehicle computers memorize and store vehicle operation patterns
for optimum driveability and performance. When vehicle battery is
disconnected, this memory is lost. The computer will use default data
until new data from each key start is stored. As computer memorizes
vehicle operation for each new key start, driveability is restored.
Vehicle computers may memorize vehicles operation patterns for 40 of
more key starts.
Customers often complain of driveability problems during
relearn stage because vehicle acts differently then before being
serviced. Depending on type and make of vehicle and how it is
equipped, the following complaints (driveability problems) may exist:
* Harsh Or Poor Shift Quality
* Rough Or Unstable Idle
* Hesitation Or Stumble
* Rich Or Lean Running
* Poor Fuel Mileage
These symptoms and complaints should disappear after a number
of drive cycles have been memorized. To reduce the possibility of
complaints, after any service which requires battery power to be
disconnected, vehicle should be road tested. If a specific relearn
procedure is not available, the following procedure may be used:
Automatic Transmission
* Set parking brake, start engine in "P" or "N" position.
Warm-up vehicle to normal operating temperature or until
cooling fan cycles.
* Allow vehicle to idle for one minute in "N" position. Select
"D" and allow engine to idle for one minute.
* Accelerate at normal throttle position (20-50%) until vehicle
shifts into top gear.
* Cruise at light to medium throttle.
* Decelerate to a stop, allowing vehicle to downshift, and use
brakes normally.
* Process may be repeated as necessary.
Manual Transmission

ELECTRIC COOLING FAN
COMPONENT TESTING
Radiator Fan Motor (Diamante)
1) Disconnect radiator fan motor connectors A39 and A40.
Ground fan motor connector A39 terminal No. 2 (Black wire). Using a
fused jumper wire, connect battery voltage to fan motor connector A39
terminal No. 1 (Blue/Black wire). See Fig. 7. See WIRING DIAGRAMS. Fan
motor should operate at low speed with no abnormal noises or
interferences. Repair or replace components as necessary.
2) Ground fan motor connector A39 terminal No. 2 (Black wire)\
and connector A40 terminal No. 2 (Black wire). Using a fused jumper
wire, connect battery voltage to fan motor connector A39 terminal No.
1 (Blue/Black wire). See Fig. 7. See WIRING DIAGRAMS. Fan motor should
operate at medium speed with no abnormal noises or interferences.
Repair or replace components as necessary.
3) Ground fan motor connector A39 terminal No. 2 (Black wire)\
and connector A40 terminal No. 2 (Black wire). Using 2 fused jumper
wires, connect battery voltage to fan motor connector A39 terminal No.
1 (Blue/Black wire) and to connector A40 terminal No. 1 (Green wire)\
.
See Fig. 7. See WIRING DIAGRAMS. Fan motor should operate at high
speed with no abnormal noises or interferences. Repair or replace
components as necessary.
Fig. 7: Testing Radiator Fan Motor (Diamante)
Courtesy of Mitsubishi Motor Sales of America.
Radiator Fan Motor (Eclipse)
1) Disconnect radiator fan motor 4-pin connector. Ground fan

motor connector terminal No. 2 (Black wire). Using a fused jumper
wire, connect battery voltage to fan motor connector terminal No. 1
(White/Black wire). See WIRING DIAGRAMS. Fan motor should operate with
no abnormal noises or interferences. Repair or replace components as
necessary.
2) On all models except 1998 2.0L non-turbo, ground fan motor
4-pin connector terminal No. 4 (Black wire). Using a fused jumper
wire, connect battery voltage to fan motor connector terminal No. 3
(White/Blue wire). See WIRING DIAGRAMS. Fan motor should operate with
no abnormal noises or interferences. Repair or replace components as
necessary.
Radiator Fan Motor (Galant)
1) Disconnect radiator fan motor 4-pin connector. Ground fan
motor connector terminal No. 2 (Black wire). Using a fused jumper
wire, connect battery voltage to fan motor connector terminal No. 1
(Blue wire). See WIRING DIAGRAMS. Fan motor should operate with no
abnormal noises or interferences. Repair or replace components as
necessary. If no problems exist, go to next step.
2) Ground fan motor 4-pin connector terminal No. 4 (Black
wire). Using a fused jumper wire, connect battery voltage to fan motor
connector terminal No. 3 (Blue/Black wire). See WIRING DIAGRAMS. Fan
motor should operate with no abnormal noises or interferences. Repair
or replace components as necessary.
Radiator Fan Motor (Mirage)
Disconnect radiator fan motor 2-pin connector. Ground fan
motor 2-pin connector terminal No. 2 (Black wire). Using a fused
jumper wire, connect battery voltage to 2-pin connector terminal No. 1
(Blue/Black wire). See WIRING DIAGRAMS. Fan motor should operate with
no abnormal noises or interferences. Repair or replace components as
necessary.
Radiator Fan Motor (3000GT)
1) Disconnect radiator fan motor 4-pin connector. Ground fan
motor connector terminal No. 4 (Blue/Green wire). Using a fused jumper\
wire, connect battery voltage to fan motor connector terminal No. 2
(Red/Black wire). See WIRING DIAGRAMS. Fan motor should operate with
no abnormal noises or interferences. Repair or replace components as
necessary. If radiator fan motor operates as specified, go to next
step.
2) Disconnect battery voltage and ground from radiator fan
motor 4-pin connector. Using an ohmmeter, measure resistance between
radiator fan motor 4-pin connector terminals No. 1 (Black wire) and
No. 3 (Yellow/Blue wire). See WIRING DIAGRAMS. Resistance should be 0.
29-0.35 ohms. Replace radiator fan motor if resistance is not as
specified.
Condenser Fan Motor (Diamante)
1) Using a fused jumper wire, connect battery voltage to
condenser fan motor 4-pin connector terminal No. 1 (Blue/White wire).
Connect ground to connector terminal No. 2 (Black wire). Fan motor
should operate with no abnormal noises or interferences. Repair or
replace components as necessary. If no problems exist, go to next
step.
2) Using a fused jumper wire, connect battery voltage to
condenser fan motor 4-pin connector terminal No. 3 (Yellow wire). When\
terminal No. 4 (Black wire) is connected to ground, condenser fan
should operate faster. Replace condenser fan if operation is not as
specified. Ensure there are no abnormal noises or interferences during
fan operation.
Condenser Fan Motor (Eclipse)

1) Using a fused jumper wire, connect battery voltage to
condenser fan motor 4-pin connector terminal No. 1 (Blue wire).
Connect ground to connector to terminal No. 4 (Black wire). Fan motor
should operate with no abnormal noises or interferences. Repair or
replace components as necessary. If no problems exist, go to next
step.
2) Using a fused jumper wire, connect battery voltage to
condenser fan motor 4-pin connector terminal No. 3 (Blue/White wire).
When terminal No. 2 (Black wire) is connected to ground, condenser fan\
should operate faster. Replace condenser fan if operation is not as
specified. Ensure there are no abnormal noises or interferences during
fan operation.
Condenser Fan Motor (Galant)
1) Using a fused jumper wire, connect battery voltage to
condenser fan motor 4-pin connector terminal No. 1 (Blue wire).
Connect ground to connector to terminal No. 2 (Black wire). Fan motor
should operate with no abnormal noises or interferences. Repair or
replace components as necessary. If no problems exist, go to next
step.
2) Using a fused jumper wire, connect battery voltage to
condenser fan motor 4-pin connector terminal No. 3 (Blue/White wire).
When terminal No. 4 (Black wire) is connected to ground, condenser fan\
should operate faster. Replace condenser fan if operation is not as
specified. Ensure there are no abnormal noises or interferences during
fan operation.
Condenser Fan Motor (Mirage)
Disconnect radiator fan motor 2-pin connector. Ground fan
motor 2-pin connector terminal No. 2 (Black/Blue wire). Using a fused
jumper wire, connect battery voltage to 2-pin connector terminal No. 1
(Black/Orange wire). See WIRING DIAGRAMS. Fan motor should operate
with no abnormal noises or interferences. Repair or replace components
as necessary.
Condenser Fan Motor (Montero & Montero Sport)
Disconnect radiator fan motor 2-pin connector. Ground fan
motor 2-pin connector terminal No. 1 (Blue/Black wire). Using a fused
jumper wire, connect battery voltage to 2-pin connector terminal No. 2
(Blue/White wire). See WIRING DIAGRAMS. Fan motor should operate with
no abnormal noises or interferences. Repair or replace components as
necessary.
Condenser Fan Motor (1997 3000GT)
1) Disconnect both condenser fan motor 2-pin connectors
located on driver side of radiator. Ground fan motor 2-pin connector
terminal No. 2 (Black wire). Using a fused jumper wire, connect
battery voltage to 2-pin connector terminal No. 1 (Blue wire). See
WIRING DIAGRAMS . Fan motor should operate with no abnormal noises or
interferences. Repair or replace components as necessary. If no
problems exist, go to next step.
2) Ground fan motor 2-pin connector terminal No. 2
(Blue/Black wire). Using a fused jumper wire, connect battery voltage
to 2-pin connector terminal No. 1 (Blue/White wire). See
WIRING DIAGRAMS . Fan motor should operate with no abnormal noises or
interferences. Repair or replace components as necessary.
Condenser Fan Motor (1998 3000GT)
1) Disconnect condenser fan motor 3-pin connector located on
driver-side of radiator. Ground fan motor 2-pin connector terminal No.
3 (Black wire). Using a fused jumper wire, connect battery voltage to
3-pin connector terminal No. 1 (Blue/White wire). See WIRING DIAGRAMS.
Fan motor should operate with no abnormal noises or interferences.

Repair or replace components as necessary. If no problems exist, go to
next step.
2) Ground fan motor 3-pin connector terminal No. 3 (Black
wire). Using a fused jumper wire, connect battery voltage to 3-pin
connector terminal No. 2 (Blue wire). See WIRING DIAGRAMS. Fan motor
should operate with no abnormal noises or interferences. Repair or
replace components as necessary.
Engine Coolant Temperature (ECT) Sensor
Remove ECT sensor from vehicle. Suspend sensor in water so
that sensor does not touch container. Slowly heat water. Using an
ohmmeter, check sensor continuity as temperature increases. Replace
ECT sensor if resistance is not as specified. See
ENGINE COOLANT TEMPERATURE SENSOR RESISTANCE table.
ENGINE COOLANT TEMPERATURE SENSOR RESISTANCE









\









\









\









\









\









\









\







Temperature F (C) Ohms
Diamante, Eclipse 2.0L Turbo & 2.4L
32 (0) ................................................. 5100-6500\
68 (20) ................................................ 2100-2700\
104 (40) ................................................ 900-1300\
176 (80) ................................................. 260-360\
Eclipse Non-Turbo
77 (25) ................................................. 900-1100\
212 (100) ................................................ 600-800\
Galant & Mirage
68 (20) ................................................ 2100-2700\
176 (80) ................................................. 260-360\
Montero
68 (20) ................................................ 2130-2610\
176 (80) ................................................. 258-322\
Montero Sport
68 (20) ................................................ 2100-2700\
176 (80) ................................................. 260-360\
3000GT
32 (0) ...................................................... 5800\
68 (20) ..................................................... 2400\
104 (40) .................................................... 1100\
176 (80) ..................................................... 300\









\









\









\









\









\









\









\







Electric Cooling Fan Relay (Diamante, Eclipse, Galant &
Mirage)
1) Remove radiator fan motor relay from relay box located at
right side of engine compartment. Check for continuity between relay
terminals No. 1 and 3. If continuity exists, go to next step. If
continuity does not exist, replace cooling fan relay. See Fig. 8.
2) Using a fused jumper wire, connect battery voltage to
cooling fan relay terminal No. 1. Using another jumper wire, connect
cooling fan relay terminal No. 3 to battery ground. With cooling fan
relay energized, there should be continuity between cooling fan relay
terminals No. 4 and 5. With cooling fan relay not energized, there
should be no continuity between terminals No. 4 and 5. If continuity
does not exist as specified, replace cooling fan relay. See Fig. 8.
Electric Cooling Fan Relay (Montero, Montero Sport & 3000GT)
1)Remove relay from relay box in engine compartment relay
box. Check for continuity between relay terminals No. 2 and 4. If
continuity exists, go to next step. If continuity does not exist,
replace cooling fan relay. See Fig. 9.
2) Using a fused jumper wire, connect battery voltage to

cooling fan relay terminal No. 2. Using another jumper wire, connect
cooling fan relay terminal No. 4 to battery ground. With cooling fan
relay energized, there should be continuity between cooling fan relay
terminals No. 1 and 3. With cooling fan relay not energized, there
should be no continuity between terminals No. 1 and 3. If continuity
does not exist as specified, replace cooling fan relay. See Fig. 9.
Fig. 8: Testing Electric Cooling Fan Relay (Diamante, Eclipse,
Galant & Mirage)
Courtesy of Mitsubishi Motor Sales of America.

Fig. 25: Identifying Cruise Control Circuit Connector Terminals:
Closed Throttle Switch & Throttle Position Sensor Connector
Courtesy of Mitsubishi Motor Sales of America
INSPECTION PROCEDURES FOR TROUBLE SHOOTING SYMPTOMS
Test No. 1
Defect in power supply system (including ground) for
diagnostic line may be possible. Probable causes are:
* Malfunction of connector.
* Malfunction of harness.
1) Check voltage between data link connector pin No. 16 and
ground. See Fig. 35. If battery voltage is present, go to next step.
If battery voltage is not present, check junction block connectors C-
81 and C-94. See Figs. 19, 21, 26 and 27. If connectors are defective,
repair as necessary. If connectors are okay and malfunction remains,
check harness between power supply and data link connector. Repair as
necessary.
2) At data link connector, measure continuity between pin No.
4 and ground and pin No. 5 and ground. If continuity is present,
replace scan tool. If continuity is not present, check data link
connector for damage or loose connections. Repair as necessary. If
connector is okay and malfunction remains, check harness between data
link connector and ground. Repair as necessary.

Fig. 30: Identifying Junction Block Connectors & Joint Connectors:
Joint Connector C-132
Courtesy of Mitsubishi Motor Sales of America
Test No. 2
Malfunction of cruise control main switch or cruise control
ECU ground circuit may be present. Probable causes are:
* Malfunction of cruise control main switch.
* Malfunction of connector.
* Malfunction of harness.
* Malfunction of cruise control ECU.
1) Check cruise control main switch. See
CRUISE CONTROL SWITCH TESTS under COMPONENT TESTS. If switch is okay,
go to next step. If switch is defective, repair or replace as
necessary.
2) Disconnect main switch connector C-01. See Fig. 8. At
harness side of connector, measure voltage between connector terminal
No. 1 and ground. If battery voltage is present, go to next step. If
battery voltage is not present, check condition of junction block
connectors C-94 and C-101. If connector(s) are defective, repair as
necessary. If connectors are okay and malfunction remains, check
harness between cruise control main switch and power supply. Repair as
necessary.
3) Check condition of cruise control main switch connector C-
01, joint connector C-132 and cruise control ECU connector C-50.
Repair as necessary. If connectors are okay and malfunction remains,
check harness between cruise control main switch and ground, and
between main switch and cruise control ECU. Repair as necessary.
4) Disconnect cruise control ECU connector C-50. See Fig. 13.
Check for continuity between ground and connector terminals No. 6, 8,
and 14. If continuity is present, go to next step. If continuity is
not present, check condition of connectors between front wiring

harness, dash wiring harness and joint connector C-132. Repair as
necessary. If malfunction remains, check harness between cruise
control main switch and power supply. Repair as necessary.
5) Check condition of cruise control ECU connector C-50.
Repair as necessary. If connector is okay and malfunction persists,
replace cruise control ECU.
Test No. 3
Malfunction of cruise control main switch or cruise control
ECU ground circuit may be present. Probable causes are:
* Malfunction of cruise control main switch.
* Malfunction of clockspring.
* Malfunction of connector.
* Malfunction of harness.
1) Check cruise control switches. See
CRUISE CONTROL SWITCH TESTS under COMPONENT TESTS. Replace any failed
switch. If switches are okay, check clockspring. See CLOCKSPRING TEST
under COMPONENT TESTS. If clockspring is okay, go to next step.
Replace clockspring if not okay.
2) Disconnect clockspring connector C-128 and measure voltage
between terminal No. 2 and ground. See Fig. 15. If battery voltage is
present, go to next step. If battery voltage is not present, check
condition of IOD connector A-09X, joint connector C-131, junction
block connector C-81, junction block connector C-94 and junction block
connector C-101. Repair as necessary. See Figs. 4, 16, 19, 21, 22, 26,
27 and 29. If connectors are okay and malfunction remains, check
harness between clockspring and power supply. Repair as necessary.
3) Check condition of cruise control ECU connector C-50 and
clockspring connector C-128. Repair as necessary. See Figs. 13 and 15.
If connectors are okay and malfunction remains, check harness between
clockspring and cruise control ECU. Repair as necessary.
Test No. 4
Malfunction of stoplight switch or stoplight circuit may be
present. Probable causes are:
* Malfunction of stoplight switch.
* Malfunction of connector.
* Malfunction of harness.
* Malfunction of cruise control ECU.
1) If stoplight does not illuminate with brake pedal
depressed, go to next step. If stoplight illuminates with pedal
depressed, replace cruise control ECU.
2) Check stoplight switch. See
BRAKELIGHT/STOPLIGHT SWITCH TEST under COMPONENT TESTS. Replace
stoplight switch as necessary. If stoplight switch is okay, go to next
step.
3) Disconnect stoplight switch connector C-55. See Fig. 14.
At harness side of connector, measure voltage between terminal No. 2
and ground. If battery voltage is present, go to next step. If battery
voltage is not present, check condition of joint connector C-131 and
junction block connector C-94. Repair as necessary. See Fig. 26. If
connectors are okay and malfunction remains, check harness between
stoplight switch and power supply. Repair as necessary.
4) Check condition of cruise control ECU connector C-50 and
stoplight switch connector C-55. Repair as necessary. If connectors
are okay and malfunction remains, check harness between stoplight
switch and cruise control ECU. Repair as necessary.
Test No. 5