steering MITSUBISHI MONTERO 1998 Workshop Manual

temperature gauge reading. If readings are about the same, go to next
step. If readings are not about the same, go to DTC P0115 test.
7) Using a thermometer, check engine compartment ambient
temperature. Using scan tool, read Intake Air Temperature (IAT) sensor\
temperature (item 13). Compare IAT sensor and thermometer readings. If\
readings are not about the same, go to DTC P0110 test. If readings are
about the same, go to next step.
8) Using scan tool, read Power Steering Pressure (PSP) switc\
h
status (item 27). Switch status should read ON when steering wheel is
turned. If switch status is as specified, go to step 24). If switch
status is not as specified, go to DTC P0551 test.
9) Remove fuel cap. Install a fuel tank filler tube adapter
in place of fuel cap. Plug fuel filler tube adapter hose. Disconnect
and plug air filter-to-EVAP vent solenoid hose at air filter.
Disconnect intake manifold plenum-to-EVAP purge solenoid at intake
manifold plenum. Install a "T" fitting between vacuum hose and intake
manifold plenum. Connect hand-held pressure/vacuum pump to "T"
fitting. Go to next step.
CAUTION: DO NOT apply more than 0.57 psi in following step. Applying
more than specified psi can crack fuel tank.
NOTE: Ensure fuel tank is at least 1/4 full. The lower the fuel
level in fuel tank, the longer it takes to pressurize fuel
system.
10) Using scan tool, read Fuel Tank Differential Pressure
(FTDP) sensor (item 73). Using hand-held pressure/vacuum pump, apply\
0.42 psi. If scan tool reading reaches 0.42 psi, replace fuel cap. Go
to step 24). If reading does not reach 0.42 psi, go to next step.
11) Disconnect hand-held pressure/vacuum pump from "T"
fitting. Install an evaporative emission system tester in place of
vacuum held pump and apply 0.49 psi. Wait two minutes. If pressure
drops less than 0.20 psi, go to next step. If pressure drops 0.29 psi
or more, go to step 14).
12) Disconnect EVAP purge solenoid-to-EVAP canister hose at
EVAP canister. Connect hand-held pressure/vacuum pump to hose and
apply 0.9 psi. If pressure is not maintained, check EVAP purge
solenoid for leak. If EVAP purge solenoid is okay, replace hose. Go to
step 24). If pressure is maintained, go to next step.
13) Disconnect EVAP vent solenoid-to-EVAP canister hose at
EVAP canister. Connect hand-held pressure/vacuum pump to hose and
apply 0.9 psi. If pressure is not maintained, check EVAP vent solenoid
for leak. If EVAP vent solenoid is okay, replace hose. Go to step 24).
If pressure is maintained, replace EVAP canister. Go to step 24).
14) Ensure hoses are properly routed and connected. See M -
VACUUM DIAGRAMS article. Install hoses as necessary and go to step
24). If hoses are okay, go to next step.
15) Disconnect OFLV-to-EVAP canister hose at OFLV and EVAP
canister. Plug hose at OFLV end. Connect hand-held pressure/vacuum
pump to hose at EVAP canister end. Apply 0.9 psi. If pressure is not
maintained, replace hose. Go to step 24). If pressure is maintained,
go to next step.
16) Using scan tool, read Fuel Tank Differential Pressure
(FTDP) sensor (item 73). Connect hand-held pressure/vacuum pump to
OFLV. While monitoring scan tool, apply 0.42 psi. If scan tool reading
reaches 0.42 psi, go to next step. If reading does not reach 0.42 psi,
go to step 20).
17) Disconnect OFLV-to-EVAP canister hose at EVAP canister.
Connect hand-held pressure/vacuum pump to hose and apply 0.9 psi. If
pressure is not maintained, go to next step. If pressure is
maintained, go to step 19).
18) Disconnect EVAP purge solenoid-to-EVAP canister hose at

system.
3) Using scan tool, read Fuel Tank Differential Pressure
(FTDP) sensor (item 73). Using hand-held pressure/vacuum pump, apply\
0.42 psi. If scan tool reading reaches 0.42 psi, go to next step. If
reading does not reach 0.42 psi, go to step 8).
4) Disconnect EVAP canister purge hose. Connect Purge Flow
Indicator (MB995061) between EVAP canister and disconnected hose. Turn\
engine on and allow it to reach operating temperature. Turn all lights
and accessories off. Place transmission in Park or Neutral. Observe
purge flow indicator while increasing engine RPM several times. If
purge flow indicator reads less than 2.5 SCFH (20 cm(3)/sec), check
EVAP canister purge hose and EVAP canister port for clogging. If hose
and port are okay, check EVAP purge solenoid. See DTC P0443. If
solenoid is okay, replace EVAP canister. Go to step 20).
5) Using scan tool, read Engine Coolant Temperature (ECT)
sensor temperature (item 21). Compare scan tool reading with
temperature gauge reading. If readings are about the same, go to next
step. If readings are not about the same, go to DTC P0115 test.
6) Using a thermometer, check engine compartment ambient
temperature. Using scan tool, read Intake Air Temperature (IAT) sensor\
temperature (item 13). Compare IAT sensor and thermometer readings. If\
readings are not about the same, go to DTC P0110 test. If readings are
about the same, go to next step.
7) Using scan tool, read Power Steering Pressure (PSP) switc\
h
status (item 27). Switch status should read ON when steering wheel is
turned. If switch status is as specified, go to step 20). If switch
status is not as specified, go to DTC P0551 test.
8) Remove fuel cap. Install a fuel tank filler tube adapter
in place of fuel cap. Plug fuel filler tube adapter hose. Disconnect
and plug air filter-to-EVAP vent solenoid hose at air filter.
Disconnect intake manifold plenum-to-EVAP purge solenoid at intake
manifold plenum. Install a "T" fitting between vacuum hose and intake
manifold plenum. Connect hand-held pressure/vacuum pump to "T"
fitting. Go to next step.
CAUTION: DO NOT apply more than 0.57 psi in following step. Applying
more than specified psi can crack fuel tank.
NOTE: Ensure fuel tank is at least 1/4 full. The lower the fuel
level in fuel tank, the longer it takes to pressurize fuel
system.
9) Using scan tool, read Fuel Tank Differential Pressure
(FTDP) sensor (item 73). Using hand-held pressure/vacuum pump, apply\
0.42 psi. If scan tool reading reaches 0.42 psi, replace fuel cap. Go
to step 20). If reading does not reach 0.42 psi, go to next step.
10) Disconnect hand-held pressure/vacuum pump from "T"
fitting. Install an evaporative emission system tester in place of
vacuum held pump and apply 0.49 psi. Wait two minutes. If pressure
drops less than 0.20 psi, go to next step. If pressure drops 0.29 psi
or more, go to step 13).
11) Disconnect EVAP purge solenoid-to-EVAP canister hose at
EVAP canister. Connect hand-held pressure/vacuum pump to hose and
apply 0.9 psi. If pressure is not maintained, check EVAP purge
solenoid for leak. If EVAP purge solenoid is okay, replace hose. Go to
step 24). If pressure is maintained, go to next step.
12) Disconnect EVAP vent solenoid-to-EVAP canister hose at
EVAP canister. Connect hand-held pressure/vacuum pump to hose and
apply 0.9 psi. If pressure is not maintained, check EVAP vent solenoid
for leak. If EVAP vent solenoid is okay, replace hose. Go to step 20).
If pressure is maintained, replace EVAP canister. Go to step 24).
13) Ensure hoses are properly routed and connected. See M -

9) Test is complete. Intermittent problem may exist. Road
test vehicle (if necessary) and attempt to duplicate conditions that
caused original complaint. Recheck for DTCs. If no DTCs are displayed,
go to INTERMITTENT DTCS .
10) Road test vehicle and attempt to duplicate conditions
that caused original complaint. Recheck for DTCs. If no DTCs are
displayed, test is complete.
DTC P0510: CLOSED THROTTLE POSITION (TP) SWITCH FAILURE
NOTE: Closed TP switch is built into TP sensor. For DTC P0510
test purposes, TP sensor will be referred to as closed
TP switch. For terminal identification, see TP sensor under
TERMINAL IDENTIFICATION . For circuit and wire color
identification, see L - WIRING DIAGRAMS article.
1) If using scan tool, go to step 3). Disconnect closed TP
switch connector. Check for continuity between closed TP switch
connector terminals No. 1 and 2 on Montero or No. 3 and 4 on 3000GT.
Go to next step.
2) Depress accelerator pedal. Continuity should not exist.
Release accelerator pedal. Continuity should exist. If continuity is
not as specified, replace TP sensor. If continuity is as specified, go
to step 4).
3) Using scan tool, read closed TP switch state (item 26).
With accelerator pedal released, scan tool should read ON. With
accelerator pedal slightly depressed, scan tool should read OFF. If
closed TP switch does not test as specified, replace TP sensor. If
closed TP switch tests as specified, disconnect closed TP switch
connector and go to next step.
4) On 3000GT, go to next step. On Montero, turn ignition
switch to OFF position. Disconnect PCM connector. Ground PCM connector
terminal No. 79. Using DVOM, check continuity between chassis ground
and closed TP switch connector terminal No. 2. If continuity does not
exist, repair wiring harness as necessary. If continuity exists, go to
next step.
5) Check continuity between chassis ground and closed TP
switch connector terminal No. 1 on Montero or No. 4 on 3000GT. If
continuity does not exist, repair wiring harness as necessary. If
continuity exists, go to next step.
6) Turn ignition switch to ON position. Check voltage between
chassis ground and closed TP switch connector terminal No. 2 on
Montero or No. 3 on 3000GT. If voltage is less than 4 volts, replace
PCM. If voltage is more than 4 volts, condition required to set DTC is
not present at this time. Go to next step.
7) Test is complete. Intermittent problem may exist. Road
test vehicle (if necessary) and attempt to duplicate conditions that
caused original complaint. Recheck for DTCs. If no DTCs are displayed,
go to INTERMITTENT DTCS .
DTC P0551: POWER STEERING PRESSURE (PSP) SENSOR CIRCUIT
PERFORMANCE
NOTE: For terminal identification, see TERMINAL IDENTIFICATION. For
circuit and wire color identification, see
L - WIRING DIAGRAMS article.
1) Using scan tool, read Power Steering Pressure (PSP) statu\
s
(item 27). Switch status should read ON when steering wheel is turned.\
If switch status is as specified, fault is intermittent. See
INTERMITTENT DTCS . If switch status is not as specified, go to next
step.

2) Disconnect pressure hose from oil pump. See Fig. 45.
Install Adapter (MB990993) on oil pump. Install Adapter (MB990994) o\
n
disconnected hose. Connect Pressure Gauge (MB990662) and shutoff valve\
between adapters. Open shutoff valve. Bleed steering hydraulic system.
See HYDRAULIC SYSTEM BLEEDING in STEERING SYSTEM article.
Fig. 45: Testing PSP Sensor Circuit
Courtesy of Mitsubishi Motor Sales of America
3) Install a thermometer in fluid reservoir. Start engine and
allow it to idle. Turn steering wheel several times until fluid
temperature reaches 122-140
F (50-60C). Disconnect PSP switch
connector. Install a DVOM between ground and PSP switch terminal. See
Fig. 45 . Note continuity reading on DVOM. Go to next step.
4) With engine idling, gradually close shutoff valve to
increase power steering system pressure. Check pressure when PSP
switch is actuated by watching for a change in continuity. PSP switch

GENERATOR & REGULATOR
1998 Mitsubishi Montero
1998 STARTING & CHARGING SYSTEMS
Mitsubishi - Generators & Regulators
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
DESCRIPTION & OPERATION
NOTE: The terms generator and alternator are interchangeable.
Mitsubishi generators are conventional 3-phase, self-
rectifying type units containing 6 diodes (3 positive and 3 negative)
which are used to rectify current. All models use a case-mounted
Integrated Circuit (IC) voltage regulator.
Generator relay or resistor with diode is used to ensure
charging of battery even if charging indicator light is defective.
ADJUSTMENTS
BELT TENSION
For belt tension, see DRIVE BELT ADJUSTMENT table.
DRIVE BELT ADJUSTMENT TABLE









\









\









\









\









\









\









\







( 1) Deflection ( 1) Deflection
Application New Belt In. (mm) Used Belt In. (mm\
)
Diamante ( 2) ........... .24-.28 (6.0-7.2) ..... .32-.37 (8.2-9.3)
Eclipse
2.0L Non-Turbo ( 3) ... .30-.41 (7.5-10.5) ... .35-.47 (9.0-12.0)
2.0L Turbo ( 4) ....... .30-.35 (7.5-9.0) ............ .39 (10.0)
2.4L ( 4) ............. .30-.35 (7.5-9.0) ............ .39 (10.0)
Galant ( 4) ............. .30-.35 (7.5-9.0) ............ .39 (10.0)
Mirage ( 3)
1.5L ................. .36-.42 (9.2-10.6) .... .26-.33 (6.6-8.3\
)
1.8L ................. .33-.39 (8.5-10.0) .... .28-.31 (7.0-8.0\
)
Montero ( 4) ............ .22-.29 (5.5-7.5) ..... .31-.35 (8.0-9.0)
Montero Sport
2.4L ( 4) ............. .22-.29 (5.5-7.5) ..... .30-.33 (7.5-8.3)
3.0L ( 4) ............. .22-.29 (5.5-7.5) ..... .31-.35 (8.0-9.0)
3000GT
DOHC ( 5) ............. .14-.16 (3.5-4.0) ..... .16-.20 (4.0-5.0)
SOHC ( 6) ............. .16-.20 (4.0-5.0) ..... .24-.32 (6.0-8.0)
( 1) - With 22 lbs. (10 kg) pressure applied midway on belt run.
( 2) - Measure between A/C compressor pulley and crankshaft pulley.
( 3) - Measure between crankshaft pulley and generator pulley.
( 4) - Measure between water pump pulley and generator pulley.
( 5) - Measure between crankshaft pulley and idler pulley.
( 6) - Measure between power steering pulley and idler pulley.









\









\









\









\









\









\









\







TROUBLE SHOOTING
NOTE: See TROUBLE SHOOTING article in the GENERAL INFORMATION
section.

* Check power supply to PCM.
* Check fuel pressure.
* Check ignition timing.
* Check for disconnected or damaged vacuum hoses.
* Check for control relay malfunction.
* Check for SFI system malfunction.
* Check for fuel pump drive control system malfunction.
* Check for ignition coil malfunction.
* Check for power transistor malfunction (if applicable).
* Check for fuel injector malfunction.
* Check for PCM malfunction.
* Ensure electrical harness, connectors and wires are not
broken, bent or loose.
ROUGH OR UNSTABLE IDLE
* Check intake air temperature sensor.
* Check EVAP purge control solenoid valve (if applicable).
* Check vehicle speed sensor.
* Check engine coolant temperature sensor.
* Check barometric pressure sensor (if applicable).
* Check manifold absolute pressure sensor (if applicable).
* Check ignition switch.
* Check throttle position sensor.
* Check camshaft position sensor.
* Check crankshaft position sensor.
* Check power steering oil pressure switch (if applicable).
* Check A/C switch and power relay (if applicable).
* Check park/neutral position switch (A/T).
* Check heated oxygen sensor.
* Check volume airflow sensor.
* Check fuel pressure.
* Check for disconnected or damaged vacuum hoses.
* Check for SFI system malfunction.
* Check idle air control (DC) motor (if applicable).
* Check idle air control (stepper) motor (if applicable).
* Check for fuel injector malfunction.
* Check for power transistor malfunction (if applicable).
* Check for vehicle speed sensor malfunction.
* Check for PCM malfunction.
* Ensure electrical harness, connectors and wires are not
broken, bent or loose.
ENGINE HESITATES OR POOR ACCELERATION
* Check intake air temperature sensor.
* Check engine coolant temperature sensor.
* Check barometric pressure sensor (if applicable).
* Check manifold absolute pressure sensor (if applicable).
* Check ignition switch.
* Check ignition coil.
* Check EGR control solenoid valve (if applicable).
* Check throttle position sensor.
* Check camshaft position sensor.
* Check crankshaft position sensor.
* Check power steering oil pressure switch (if applicable).
* Check A/C switch and power relay (if applicable).
* Check park/neutral position switch (A/T).
* Check heated oxygen sensor.
* Check volume airflow sensor.
* Check fuel pressure.
* Check for disconnected or damaged vacuum hoses.
* Check for SFI system malfunction.

* Check idle air control (DC) motor (if applicable).
* Check idle air control (stepper) motor (if applicable).
* Check for fuel injector malfunction.
* Check for power transistor malfunction (if applicable).
* Check A/C switch and power relay (if applicable).
* Check for PCM malfunction.
* Ensure electrical harness, connectors and wires are not
broken, bent or loose.
ENGINE SURGES
* Check engine coolant temperature sensor.
* Check EGR control solenoid valve (if applicable).
* Check fuel pressure.
* Check for fuel injector malfunction.
DETONATION OR KNOCKING
* Check for knock sensor malfunction (if applicable).
* Check volume airflow sensor.
* Check for engine cooling system problems.
* Check fuel quality.
* Check intake air temperature sensor.
* Check barometric pressure sensor (if applicable).
* Check manifold absolute pressure sensor (if applicable).
* Check ignition coil.
* Check power transistor (if applicable).
* Check for EGR system malfunction.
POOR FUEL MILEAGE
* Check intake air temperature sensor.
* Check engine coolant temperature sensor.
* Check barometric pressure sensor (if applicable).
* Check manifold absolute pressure sensor (if applicable).
* Check ignition switch.
* Check throttle position sensor.
* Check camshaft position sensor.
* Check crankshaft position sensor.
* Check power steering oil pressure switch (if applicable).
* Check A/C switch and power relay (if applicable).
* Check park/neutral position switch (A/T).
* Check heated oxygen sensor.
* Check volume airflow sensor.
* Check fuel pressure.
* Check for SFI system malfunction.
* Check idle air control (DC) motor (if applicable).
* Check idle air control (stepper) motor (if applicable).
* Check for fuel injector malfunction.
* Check for power transistor malfunction (if applicable).
INTERMITTENTS
INTERMITTENT PROBLEM DIAGNOSIS
Intermittent fault testing requires duplicating circuit or
component failure to identify problem. These procedures may lead to
computer setting a Diagnostic Trouble Code (DTC) which may help in
diagnosis.
If problem vehicle does not produce DTCs, monitor voltage or
resistance values using a DVOM while attempting to reproduce
conditions causing intermittent fault. A status change on DVOM

* PLEASE READ THIS FIRST *
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG RESTRAINT
SYSTEM article.
CAUTION: When removing or installing floor console, DO NOT allow any
impact or shock to Supplemental Restraint System Electronic
Control Unit (SRS-ECU).
FRONT HEATER UNIT & HEATER CORE
Removal
1) Deactivate air bag system. See AIR BAG RESTRAINT SYSTEM
article. Remove front and rear floor consoles. Remove hood release
handle. Remove fuel door release handle. Remove knee protector and
support brackets. Remove speaker covers.
NOTE: On A/T models, when removing front floor console, set A/T
selector lever in "L" position.
2) Remove glove box door stop, glove box and glove box frame.
Remove passenger-side air bag module. Remove heater control panel
cover. Remove heater control panel and radio. Remove plug from
instrument cluster cover. Remove instrument cluster cover and
instrument cluster.
3) Remove steering column cover. Remove clock or plug. Remove
side defroster covers. Remove side mirror control switch. Remove front
speakers.
4) Remove rheostat, rear wiper/washer switch, and door lock
switch. Disconnect ventilation control cable and harness connector.
See Fig. 9. Remove instrument panel. See INSTRUMENT PANEL. Drain
coolant and disconnect heater hoses from heater unit.
5) Remove shower ducts, lap duct, joint duct and center duct.
See Fig. 1 . Remove center reinforcement. Remove heater unit. Remove
distribution duct. Remove heater core.
Installation
Install heater core, distribution duct, heater unit and
center reinforcement. Install remaining ducts in reverse order of
removal. Install instrument panel. Tighten steering column bolts to 16
ft. lbs. (22 N.m). Install and adjust ventilation control cable. See
ADJUSTMENTS . To complete installation, reverse removal procedure. Add
coolant and check for leaks.
INSTRUMENT PANEL
Removal & Installation
Remove instrument panel components and then instrument panel,
in order listed on appropriate illustration. See Fig. 9. To install,
reverse removal procedures.

Brake On/Off (BOO) Switch ................... Cruise Control Systems\
Engine Performance
Shift Interlock Systems
Buzzer Module ...................................... Warning Systems
Camshaft Position (CMP) Sensor .................. Engine Performance\
Central Control Module ........................... Anti-Theft System
Clockspring ............................... Air Bag Restraint System
Cruise Control Systems
Steering Column Switches
Clutch Pedal Position Switch .............................. Starters
Clutch Start Switch ....................................... Starters
Combination Meter ......................... Analog Instrument Panels
Constant Control Relay Module (CCRM) ............ Engine Performance\
Electric Cooling Fans
Convenience Center .............................. Power Distribution
Illumination/Interior Lights
Convertible Top Motor ........................ Power Convertible Top
Convertible Top Switch ....................... Power Convertible Top
Crankshaft Position (CKP) Sensor ................ Engine Performance\
Cruise Control Module ....................... Cruise Control Systems
Cruise Control Switch ....................... Cruise Control Systems
Condenser Fan Relay(s) ....................... Electric Cooling Fans\
Data Link Connector (DLC) ....................... Engine Performance\
Daytime Running Lights Module ............... Daytime Running Lights
Exterior Lights
Defogger Relay ................................ Rear Window Defogger
Diagnostic Energy Reserve Module (DERM) ... Air Bag Restraint System\
Discriminating Sensor (Air Bag) ........... Air Bag Restraint System\
Distributor ..................................... Engine Performance
Door Lock Actuators ............................... Power Door Locks
Remote Keyless Entry
Door Lock Relay(s) ................................ Power Door Locks\
Electrochromic Mirror ................................ Power Mirrors
Electronic Level Control (ELC)
Height Sensor .............................. Electronic Suspension
Electronic Level Control (ELC) Module ........ Electronic Suspension\
Engine Coolant Temperature (ECT)
Sending Unit ............................ Analog Instrument Panels
Engine Coolant Temperature (ECT) Sensor ......... Engine Performance\
Engine Control Module ........................... Engine Performance
Generators & Regulators
Starters
ETACS ECU .......................................... Warning Systems
Power Windows
Remote Keyless Entry
Evaporative (EVAP) Emissions Canister ........... Engine Performance\
EVAP Canister Purge Solenoid .................... Engine Performance
EVAP Canister Vent Solenoid ..................... Engine Performance
Exhaust Gas Recirculation (EGR) Valve ........... Engine Performance\
Fuel Tank Vacuum Sensor ......................... Engine Performance
Fog Lights ....................................... Headlight Systems
Daytime Running Lights
Fog Light Relay .................................. Headlight Systems
Daytime Running Lights
Fuel Door Release Solenoid ................. Power Fuel Door Release
Fuel Gauge Sending Unit ................... Analog Instrument Panels
Fuel Injectors .................................. Engine Performance
Fuel Pump ....................................... Engine Performance
Fuel Pump Relay ................................. Engine Performance
Power Distribution
Fuse/Relay Block ................................ Power Distribution
Fusible Links ................................... Power Distribution
Generators & Regulators

Starters
Generator .................................. Generators & Regulators
Engine Performance
Power Distribution
Generic Electronic Module (GEM) ............... Body Control Modules\
Electronic Suspension
Glow Plug Relay ................................. Engine Performance
Glow Plugs ...................................... Engine Performance
Grounds ........................................ Ground Distribution
Headlight Door Module .............................. Headlight Doors
Headlight Relay .................................. Headlight Systems
Daytime Running Lights
Headlights ....................................... Headlight Systems
Daytime Running Lights
Heated Oxygen Sensor(s) (HO2S) .................. Engine Performan\
ce
Heated Windshield Control Module ................ Heated Windshields
Height Sensor ................................ Electronic Suspension
Horns ..................................... Steering Column Switches
Horn Relay ................................ Steering Column Switches
Idle Air Control (IAC) Motor/Valve .............. Engine Performance\
Ignition Coil(s) ................................ Engine Performance\
Ignition Key Lock Cylinder ....................... Anti-Theft System
Ignition Module ................................. Engine Performance
Ignition Switch ................................. Power Distribution
Engine Performance
Generators & Regulators
Starters
Illuminated Entry Module .............. Illumination/Interior Lights
Illumination Lights ................... Illumination/Interior Lights
Impact Sensor ............................. Air Bag Restraint System
Inertia Fuel Shutoff Switch ..................... Engine Performance
Inhibit Relay ............................................. Starters
Instrument Cluster ........................ Analog Instrument Panels
Intake Air Temperature (IAT) Sensor ............. Engine Performance\
Interior Lights ....................... Illumination/Interior Lights
Interlock Switch .......................................... Starters
Junction Block .................................. Power Distribution
Keyless Entry Receiver ........................ Remote Keyless Entry
Key Reminder Switch ....................................... Starters
Knock Sensor .................................... Engine Performance
Lamp Control Module ................................ Exterior Lights
License Plate Lamp ................................. Exterior Lights
Lighting Control Module ................... Lighting Control Modules
Anti-Theft System
Daytime Running Lights
Headlight Systems
Lower Relay .................................. Power Convertible Top
Malfunction Indicator Light (MIL) ............... Engine Performance\
Instrument Panels
Manifold Absolute Pressure (MAP) Sensor ......... Engine Performance\
Mass Airflow (MAF) Sensor ....................... Engine Performance\
Mega Fuse .................................. Generators & Regulators
Memory Seat/Mirror Module ........................... Memory Systems
Mirror Defogger ............................... Rear Window Defogger
Moon Roof Motor .................................... Power Moon Roof
Moon Roof Relay .................................... Power Moon Roof
Multi-Function Control Module ...................... Warning Systems
Neutral Safety Switch ..................................... Starters
Oil Level Switch ................................ Engine Performance
Oil Pressure Switch/Sending Unit .......... Analog Instrument Panels
Engine Performance
Overhead Console .................................. Overhead Console
Oxygen Sensor(s) (O2S) .......................... Engine Performan\
ce