ECU MITSUBISHI MONTERO 1998 Repair Manual

1) Start and run engine at 2000 RPM. Ensure battery is fully
charged. Turn defogger switch to ON position. Using a voltmeter, check
voltage at center section of each defogger grid filament.
2) If voltage is about 6 volts, grid filament is okay. If
voltage is about 12 volts, an open is present in negative circuit.
Move probe slowly toward negative terminal to determine location of
open circuit.
3) If voltage is zero volts, an open is present in positive
circuit. Move probe slowly toward positive terminal to determine
location of open circuit. Repair grid as necessary. See
GRID FILAMENT REPAIR under ON-VEHICLE SERVICE.
ON-VEHICLE SERVICE
GRID FILAMENT REPAIR
Clean broken wire tips thoroughly. Place masking tape along
both sides of broken wire. See Fig. 8. Apply Repair Paste (DuPont
4817) to broken section of grid. Remove masking tape after paste has
dried. Wait 24 hours before using defogger.
Fig. 8: Repairing Rear Defogger Grid Element
REMOVAL & INSTALLATION
DEFOGGER SWITCH
Removal & Installation (Diamante)
Defogger switch is integral with A/C system ECU. To remove
A/C ECU, remove center console. Remove audio panel. Remove radio.
Remove A/C ECU. To install, reverse removal procedure.
Removal & Installation (Eclipse)
Remove upper stoppers from glove compartment. Drop down glove
compartment. From glove compartment opening, reach behind center air
outlet assembly and disconnect harness connectors to switches. Release
metal clips from center air outlet assembly. Remove center air outlet.
Remove defogger switch from center air outlet. To install, reverse
removal procedure.
Removal & Installation (Galant)

Fig. 11: Rear Window Defogger System Wiring Diagram (Galant With
ETACS-ECU)

Fig. 12: Rear Window Defogger System Wiring Diagram (Galant Without
ETACS-ECU)

Check ring gear, pinion and side gears for wear or damage. Replace
components as necessary.
Reassembly & Adjustments
1) Place side gear thrust spacers behind side gears, in
original position. Assemble side gears in differential case. Install
pinion gears and washers. Rotate pinion gears to mesh with side gears.
2) Install pinion shaft without lock pin. Check pinion and
side gear backlash. Install wooden wedge to lock side gears. Using
dial indicator, measure gear backlash. See Fig. 5.
3) Backlash must be within specification. See
PINION & SIDE GEAR BACKLASH SPECIFICATIONS table. Adjust backlash by
using different side gear spacers. Ensure both sides are equally
shimmed. If backlash cannot be adjusted within specifications, replace
side and pinion gears as matched set.
4) Install pinion shaft lock pin. Using a punch, securely
stake lock pin in 2 places. Ensure adhesive is removed from ring gear
mounting bolts and gear mounting surface. Clean internal threads with
tap.
5) Install ring gear on differential case. Ensure alignment
marks on differential case and ring gear are aligned. Apply Loctite
271 to bolts and install bolts. Tighten bolts alternately in diagonal
sequence to specification. See TORQUE SPECIFICATIONS.
PINION & SIDE GEAR BACKLASH SPECIFICATIONS









\









\









\









\









\









\









\







Application In. (mm)\
Standard ................................................ .003 (.08)\
Wear Limit .............................................. .008 (.20)\









\









\









\









\









\









\









\







Fig. 5: Checking Pinion & Side Gear Backlash
Courtesy of Mitsubishi Motor Sales of America.
Drive Pinion Depth
1) Install pinion bearing races in carrier housing. Ensure

into left side axle housing. Install left axle shaft assembly into
axle housing, and tighten nuts to specification. See
TORQUE SPECIFICATIONS.
2) Install right axle shaft assembly into axle housing
without shim or "O" ring. Temporarily tighten nuts in diagonal
sequence to 51.6 INCH lbs. (5.8 N.m) in 2 stages. Measure clearance
between bearing case of right axle and rear axle housing end with
feeler gauge.
3) Select shims equal to sum of measured clearance plus .002-
.008" (.05-.20 mm). Remove right axle shaft, and install selected
shim(s) and "O" ring into right axle housing end. Install right axle
shaft assembly into rear axle housing. Tighten nuts in diagonal
sequence to specification. See TORQUE SPECIFICATIONS.
4) Using dial indicator, check end play of axle shaft. End
play should be .002-.008" (.05-.20 mm). If end play is not within
specification, change shim(s) to obtain correct end play. Reverse
removal procedure to install remaining components. Adjust parking
brake, and bleed brake system.
CARRIER ASSEMBLY
Removal
Raise and support vehicle. Drain gear oil. Mark drive shaft
flange-to-pinion flange position. Remove drive shaft. Remove axle
shafts. See AXLE SHAFT R & I . Support differential carrier with jack.
Remove differential carrier retaining nuts. Remove differential
carrier.
Inspection
Check for leaks at vent plug, differential carrier companion
flange and where carrier joins axle housing.
Installation
Apply sealant to axle housing surface. To install, reverse
removal procedure. Align marks on drive shaft and pinion flange.
DRIVE SHAFT
Removal
Make match marks on drive shaft yoke flange and pinion
flange. Remove bolts and drive shaft from vehicle.
Installation
To install, reverse removal procedure. Ensure match marks are
aligned. Tighten bolts to specification. See TORQUE SPECIFICATIONS.
OVERHAUL
AXLE SHAFT OVERHAUL
Removal
1) Secure axle shaft assembly in a vise, and remove one
retainer bolt from backing plate. Push bearing case completely to side
of dust cover. Place adhesive tape around edge of bearing case at
retainer bolt hole to prevent damage.
CAUTION: DO NOT damage bearing case or axle shaft when grinding or
chiseling retainer ring.
2) Secure axle shaft, and grind retainer ring until retainer
ring wall thickness is .04-.06" (1.0-1.5 mm) on axle shaft side and .
08" (2.0 mm) on bearing side. See Fig. 4.

.060 (1.52) .................................................... Red\
.067 (1.70) ................................................. Purple\
.073 (1.85) ................................................... Blue\
.079 (2.01) ................................................. Yellow\
.085 (2.16) ................................................ Neutral\









\









\









\









\









\









\









\







DIFFERENTIAL ASSEMBLY (CONVENTIONAL)
Pre-Disassembly Inspection
1) Secure differential assembly in appropriate holder. Secure
drive pinion from turning. Mount dial indicator on case and check ring
gear backlash at 4 positions. See Fig. 6. Backlash should be .005-.
007" (.13-.18 mm).
2) Remount dial indicator and measure ring gear runout. See
Fig. 7 . On all models, runout should not exceed .002" (.05 mm).
Remount dial indicator and measure pinion gear backlash on models
without limited slip differential. See Fig. 8. Secure side gear from
turning with wedge. Backlash should be 0-.003" (0-.08 mm). Pinion gear\
backlash service limit is .008" (.20 mm).
3) Check gear tooth contact pattern between ring gear and
drive pinion gear. Apply Prussian Blue to both surfaces of ring gear
teeth. Insert brass rod between differential housing and carrier
assembly to provide resistance while turning drive pinion.
4) Turning resistance of drive pinion should be 28-33 INCH
lbs. (2.5-3.0 N.m). Rotate drive pinion until ring gear completes one
revolution. Reverse direction of rotation and return to original
starting point. Check wear pattern. See GEAR TOOTH CONTACT PATTERNS
article in GENERAL INFORMATION.
5) On Montero models with differential lock, connect air
supply hose with pressure gauge and regulator to actuator air pipe.
Apply 4 psi (.28 kg/cm
) of pressure. Using Adapter Shaft (MB990992),
turn side gear on one side of carrier assembly only. Locking mechanism
should engage. To disengage, release air pressure and turn side gear
1/4-1/2 turn.
6) With lock mechanism engaged, measure turning torque of
drive pinion. Turning torque should not be less than 36 ft. lbs. (50
N.m). With lock mechanism disengaged, turning torque should not be
more than 36 ft. lbs. (50 N.m).
Fig. 6: Measuring Ring Gear Backlash
Courtesy of Mitsubishi Motor Sales of America.

assembly and drive pinion installation.
Carrier Assembly & Drive Pinion Removal
1) Remove differential carrier from axle housing. Remove lock
plates. Mark location of side bearing nuts for reassembly. Remove side
bearing nuts. See Fig. 9. Mark location of bearing caps for
reassembly. Remove bearing caps. Remove differential carrier assembly
from differential housing.
Fig. 9: Exploded View Of Conventional Rear Differential (Typical)
Courtesy of Mitsubishi Motor Sales of America.
2) Secure drive pinion companion flange from turning. Remove
companion flange retaining nut. Scribe alignment marks on drive pinion
and companion flange for reassembly. Using soft-face hammer, drive
pinion out of housing. Remove front adjusting shim and spacer from
pinion.
3) Using bearing splitter and press, remove rear bearing from
pinion. Remove rear adjusting shim from drive pinion. Remove oil seal
and bearing races from differential housing.
Disassembly (Carrier Assembly)
1) Using bearing splitter and press, remove differential case
side bearings. Place alignment marks on ring gear and differential
case for reassembly. Loosen ring gear bolts in diagonal sequence.
Remove ring gear.
2) Remove pinion shaft lock pin from differential carrier.
Remove differential pinion shaft and thrust block (if equipped).
Remove pinion gears and washers. Remove side gears and thrust spacers.
Mark components for reassembly reference.
Inspection
Wash parts in clean solvent and dry with compressed air.
Inspect bearings for discoloration and/or flaking. Check all gears for
irregular wear or damage. Ring gear and drive pinion must be replaced

as matched set. Side gears and pinion gears must be replaced as
matched set.
Reassembly & Adjustment
1) Install thrust spacers, side gears, pinion washers and
pinion gears in differential case. DO NOT install thrust block (if
equipped) at this time.
2) Install pinion shaft without lock pin. Check pinion and
side gear backlash. Install wooden wedge to lock side gears. See
Fig. 8 . Using dial indicator, measure gear backlash. Backlash should
be .0004-.0030" (.010-.080 mm). Service limit is .008" (.20 mm).
3) Adjust backlash by using different side gear spacers.
Ensure both sides are equally shimmed. Install thrust block (if
equipped) once correct backlash is obtained. Install pinion shaft lock
pin from ring gear side of carrier housing. Securely stake pin in 2
places. Ensure adhesive is removed from ring gear mounting bolts and
gear mounting surface. Clean internal threads with tap.
4) Ensure alignment marks on differential case and ring gear
align. Apply Loctite 271 to bolts, and install ring gear on
differential case. Tighten bolts in diagonal sequence to
specification. See TORQUE SPECIFICATIONS . Using appropriate adapter,
press on carrier side bearings.
DIFFERENTIAL ASSEMBLY (LIMITED SLIP)
NOTE: Manufacturer does not provide disassembly or reassembly
procedures for locking type differential. Use illustrations
for exploded views of assembly. See Figs. 11 and 12.
NOTE: See PRE-DISASSEMBLY INSPECTION under
DIFFERENTIAL ASSEMBLY (CONVENTIONAL) before disassembling
carrier assembly. For carrier assembly and drive pinion
removal, see DIFFERENTIAL ASSEMBLY (CONVENTIONAL) .
Disassembly
1) Once ring gear is removed, loosen carrier housing screws
in diagonal pattern. Separate cases and remove components. See Fig. 10
. Maintain parts in order of disassembly. Clean all parts in new
solvent.
2) Inspect condition of friction and spring plates and
friction discs. Replace disc and/or plates if worn or heat damaged.
Distortion of discs will cause incorrect clutch pressure. Scratches,
nicks or burrs on components can be repaired with an oil stone.
3) Discs must be flat and free of distortion. Check discs on
surface plate with dial indicator. Maximum warpage of friction plate
or disc is .003" (.08 mm). Inspect thickness of discs and plates.
Thickness limit between discs and plates is .004" (.10 mm).
Fig. 10: Exploded View Of Limited Slip Differential
Courtesy of Mitsubishi Motor Sales of America.

PINION ROTATING TORQUE SPECIFICATIONS table.
PINION ROTATING TORQUE SPECIFICATIONS









\









\









\









\









\









\









\







Application INCH Lbs. (N.m)\
Oil Seal Not Installed
With Lubrication ................................. 3.5-4.3 (.4-.5)\
Without Lubrication .............................. 5.2-7.8 (.6-.9)\
Oil Seal Installed
With Lubrication ............................... 5.6-6.5 (.65-.75)\
Without Lubrication .......................... 7.4-10.0 (.85-1.15)\









\









\









\









\









\









\









\







3) Install cylinder gauge in side bearing seats. Ensure flat
areas align, and gauge contacts side bearing seat firmly. Select
adjusting shim with same thickness as gap between cylinder gauge and
pinion height gauge.
4) Use minimum amount of adjusting shims. Install selected
adjusting shims between drive pinion gear and rear pinion bearing.
Using bearing installer and press, install rear pinion bearing.
5) Install drive pinion in differential housing. Install
spacer, pinion front shim(s) and front pinion bearing. DO NOT install
oil seal. Install pinion companion flange, washer and retaining nut.
Tighten nut to specification. See TORQUE SPECIFICATIONS.
6) Check pinion rotating torque. See
PINION ROTATING TORQUE SPECIFICATIONS table. Adjust rotating torque by
replacing drive pinion front shims or spacer. Once correct rotating
torque is obtained, install oil seal. Coat seal lip with grease.
Install pinion companion flange so alignment marks are correct. Apply
light coat of grease to contact area of pinion flange washer.
7) Install NEW retaining nut. Recheck pinion rotating torque.
Ensure rotating torque is within specification. Press side bearings
onto differential case. Install outer races. Install differential
carrier into differential housing. Align bearing cap index marks, and
snug carrier cap bolts. Ensure outer races and bearing caps are
installed in original location.
8) Install side bearing nuts. Tighten bearing cap bolts to
specification. See TORQUE SPECIFICATIONS . Tighten bearing nuts until
bearing outer races are seated against bearings. Adjust ring gear
backlash.
Ring Gear Backlash
1) Secure drive pinion in place. Using dial indicator, check
ring gear backlash at heel of ring gear tooth. See Fig. 6. Measure at
4 locations of ring gear. Gear backlash must be within specification.
Backlash should be .005-.007" (.13-.18 mm).
2) If backlash is less than specification, loosen side
bearing nut at back of ring gear, and tighten side bearing nut on
tooth side of ring gear by same amount. If backlash exceeds
specification, loosen side bearing nut at tooth side of ring gear, and
tighten side bearing nut at back of ring gear by same amount.
3) After adjusting backlash, tighten both side bearing nuts
half the distance between 2 adjacent holes on side bearing nut.
Recheck backlash. Ensure bearing cap bolts are tightened to
specification. See TORQUE SPECIFICATIONS .
4) Lock plates are of 2 designs for hole location of side
bearing nuts. Install proper type lock plate. Tighten lock plate bolt
to specification. See TORQUE SPECIFICATIONS. Check gear tooth contact
pattern. See GEAR TOOTH CONTACT PATTERNS article in GENERAL
INFORMATION.
Ring Gear Runout

DOOR LOCKS - POWER & KEYLESS ENTRY
1998 Mitsubishi Montero
1998 ACCESSORIES & EQUIPMENT
Mitsubishi - Keyless Entry & Power Door Locks
Montero & 3000GT
DESCRIPTION & OPERATION
On 3000GT, power door locks are controlled by driver or
passenger switches which send signals to Electronic Timer Alarm
Control System (ETACS) ECU. ETACS-ECU sends appropriate signals to
individual door lock actuators through individual relays.
The following features are incorporated in power door lock
systems that have an ETACS-ECU:
* Once locked door is closed, system will unlock door if key
remains in ignition switch.
* Continuous switching between lock and unlock of door will
disable system for about one minute.
On Montero, power door lock actuator receives signal from
individual control relay that is operated by a switch incorporated in
actuator. On all models, all door locks are actuated with operation of
one lock.
Montero and 3000GT offer optional keyless entry system. Use
of a 2-button portable remote control operates door locks within a
range of 13 ft. (4 m). Dome light flashes twice when doors are locked
and illuminates for 3 seconds when doors are unlocked. If, after 30
seconds, door(s) have not been opened when unlocked with keyless entry\
system, doors will relock.
COMPONENT LOCATIONS
COMPONENT LOCATIONS TABLE








\









\









\









\









\









\






Component Location
ETACS-ECU
3000GT ........................ Behind Left Side Of Dash
Data Link Connector (DLC) ....... Under Left Side Of Dash,
Below Steering Column
Door Lock Actuator ...................... Inside Each Door
Door Lock Relay
Montero ....................... Behind Left Side Of Dash
3000GT
No. 1 ........................ Under Left Side Of Dash
No. 2 ................. Behind Left Rear Quarter Panel
Power Door Lock Control Unit
Montero
W/O RKE .................... Behind Left Side Of Dash,
Behind Speaker
Receiver
3000GT ................. Behind Right Rear Quarter Panel
Remote Keyless Entry (RKE)
Control Unit
Montero ............... Behind Right Rear Quarter Panel
3000GT ................. Behind Left Rear Quarter Panel









\









\









\









\









\









\